-
-
Notifications
You must be signed in to change notification settings - Fork 5.5k
/
Copy pathkit-voron2-250mm.cfg
302 lines (271 loc) · 7.1 KB
/
kit-voron2-250mm.cfg
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
# VORON2 250mm config
# This is a base printer.cfg file for the VORON2 printer and matches the manual/build guide exactly
# for controllers used (dual RAMPS) and pin layout for all connected components.
# Created by "Boff" with help from the VORON community.
# For other build sizes, controllers, or non-standard pin connections, please see
# https://github.com/mzbotreprap/VORON/tree/master/Firmware/Klipper/Voron_2.1/Klipper/Configurations
# for other example Klipper configs created by the VORON community.
# This file is only an example - be sure to review and update it
# according to the specifics of your printer.
# See docs/Config_Reference.md for a description of parameters.
# *** THINGS TO CHANGE/CHECK: ***
# Arduino paths [mcu] section
# Thermistor types [extruder] and [heater_bed] sections - See 'sensor types' list at end of file
# FSR switch (z endstop) location [homing_override] section
# FSR switch (z endstop) offset for Z0 [stepper_z] section
# Probe points [quad_gantry_level] section
# Min & Max gantry corner postions [quad_gantry_level] section
# PID tune [extruder] and [heater_bed] sections
# Fine tune E steps [extruder] section
[mcu]
# Mcu for X/Y/E steppers
serial: /dev/serial/by-id/**INSERT_YOUR_ARDUINO_DEFINITION_HERE**
# Obtain definition by "ls -l /dev/serial/by-id/"
restart_method: arduino
[mcu z]
# Mcu for Z steppers
serial: /dev/serial/by-id/**INSERT_YOUR_ARDUINO_DEFINITION_HERE**
# Obtain definition by "ls -l /dev/serial/by-id/"
restart_method: arduino
[printer]
kinematics: corexy
max_velocity: 350
max_accel: 3000
max_z_velocity: 50
max_z_accel: 350
[stepper_x]
# B Stepper
step_pin: PF0
dir_pin: !PF1
enable_pin: !PD7
# X on mcu_xye
microsteps: 16
rotation_distance: 40
# 80 steps per mm - 1.8 deg - 1/16 microstepping
endstop_pin: ^PE4
# X_MAX on mcu_xye
position_min: 0
position_endstop: 250
position_max: 250
homing_speed: 100
homing_retract_dist: 5
[stepper_y]
# A Stepper
step_pin: PF6
dir_pin: !PF7
enable_pin: !PF2
# Y on mcu_xye
microsteps: 16
rotation_distance: 40
# 80 steps per mm - 1.8 deg - 1/16 microstepping
endstop_pin: ^PJ0
# Y_MAX on mcu_xye
position_min: 0
position_endstop: 250
position_max: 250
homing_speed: 100
homing_retract_dist: 5
[stepper_z]
# Z0 Stepper - Front Left
step_pin: z:PF0
dir_pin: !z:PF1
enable_pin: !z:PD7
# X on mcu_z
microsteps: 16
rotation_distance: 8
# 400 steps per mm - 1.8 deg - 1/16 microstepping
endstop_pin: ^!z:PD3
# Z_MIN on mcu_z
position_endstop: -0.2
# Offset (in mm) for nozzle to bed off z switch
position_max: 250
position_min: -2
# Set to -2 to allow room for squaring gantry with quad_gantry_level
homing_speed: 15.0
second_homing_speed: 3.0
homing_retract_dist: 3.0
[stepper_z1]
# Z1 Stepper - Rear Left
step_pin: z:PF6
dir_pin: z:PF7
enable_pin: !z:PF2
# Y on mcu_z
microsteps: 16
rotation_distance: 8
# 400 steps per mm - 1.8 deg - 1/16 microstepping
[stepper_z2]
# Z2 Stepper - Rear Right
step_pin: z:PL3
dir_pin: !z:PL1
enable_pin: !z:PK0
# Z on mcu_z
microsteps: 16
rotation_distance: 8
# 400 steps per mm - 1.8 deg - 1/16 microstepping
[stepper_z3]
# Z3 Stepper - Front Right
step_pin: z:PA4
dir_pin: z:PA6
enable_pin: !z:PA2
# E0 on mcu_z
microsteps: 16
rotation_distance: 8
# 400 steps per mm - 1.8 deg - 1/16 microstepping
[extruder]
step_pin: PA4
dir_pin: PA6
enable_pin: !PA2
# E0 on mcu_xye
microsteps: 16
rotation_distance: 5.76576
# 555 steps per mm - 1.8 deg - 1/16 microstepping (Mobius2)
nozzle_diameter: 0.400
filament_diameter: 1.750
max_extrude_only_distance: 780.0
# This is set high to allow the load/unload filament macros to run
heater_pin: PB4
# D10 on mcu_xye
max_power: 1.0
sensor_type: Generic 3950
sensor_pin: PK5
# T0 on mcu_xye
smooth_time: 3.0
control: pid
pid_Kp: 16.430
pid_Ki: 0.755
pid_Kd: 89.337
min_extrude_temp: 170
min_temp: 0
max_temp: 270
[probe]
# Inductive Probe
pin: ^z:PD2
# Z_MAX on mcu_z
x_offset: 0.0
y_offset: 25.0
z_offset: 0.00
speed: 2.0
samples: 4
# Number of times to probe a point
sample_retract_dist: 6.0
# How far to retract (in mm) from the probe point for multi-probe samples
[fan]
# Print cooling fan
pin: PH6
# D9 on mcu_xye
kick_start_time: 0.500
[heater_fan hotend_fan]
# Hotend fan
pin: z:PH6
# D9 on mcu_z
kick_start_time: 0.500
heater: extruder
heater_temp: 50.0
[heater_fan controller_fan]
# Controller fan
pin: z:PB4
# D10 on mcu_z
kick_start_time: 0.500
heater: heater_bed
heater_temp: 45.0
[heater_fan exhaust_fan]
# Exhaust fan
pin: z:PH5
# D8 on mcu_z
kick_start_time: 0.500
heater: heater_bed
heater_temp: 60.0
[heater_bed]
heater_pin: z:PB5
# D11 (servo) on mcu_z
sensor_type: NTC 100K MGB18-104F39050L32
sensor_pin: z:PK7
# T2 on mcu_z
smooth_time: 3.0
max_power: 0.75
control: pid
pid_Kp: 47.690
pid_Ki: 1.556
pid_Kd: 365.338
min_temp: 0
max_temp: 110
[homing_override]
axes: z
set_position_z: 0
gcode:
G90
G0 Z5 F600
G28 X Y
G0 X179 Y249.5 F3600
# XY Location of the FSR Switch
G28 Z
G0 Z10 F1800
G0 X125 Y125 Z20 F3600
[quad_gantry_level]
# Use QUAD_GANTRY_LEVEL to level a gantry.
gantry_corners:
-55, -7
305, 320
# Min & Max gantry corners - measure from nozzle at MIN (0,0) and MAX (250,250) to respective belt positions
points:
25, 0
25, 200
225, 200
225, 0
# Probe points
speed: 200
horizontal_move_z: 6
[display]
# RepRapDiscount 128x64 Full Graphic Smart Controller
lcd_type: st7920
cs_pin: z:PH1
sclk_pin: z:PA1
sid_pin: z:PH0
# LCD connector on mcu_z
menu_timeout: 40
encoder_pins: ^z:PC4, ^z:PC6
click_pin: ^!z:PC2
kill_pin: ^!z:PG0
### Macros ###
[gcode_macro G32]
gcode:
G28
QUAD_GANTRY_LEVEL
QUAD_GANTRY_LEVEL
G0 X125 Y125 Z20 F6000
[gcode_macro PRINT_START]
# Use PRINT_START for the slicer starting script - PLEASE CUSTOMISE THE SCRIPT FOR YOUR SLICER OF CHOICE
gcode:
M117 Homing... ; display message
G28 ; home all axes
G1 Z20 F3000 ; move nozzle away from bed
M117 Preheat (Print) ; display message
M104 S0 ; turn off hotend while waiting for bed to get to temp
[gcode_macro PRINT_END]
# Use PRINT_END for the slicer ending script - PLEASE CUSTOMISE THE SCRIPT FOR YOUR SLICER OF CHOICE
gcode:
M400 ; wait for buffer to clear
G92 E0 ; zero the extruder
G1 E-4.0 F3600 ; retract
G91 ; relative positioning
G0 Z1.00 X20.0 Y20.0 F20000 ; move nozzle to remove stringing
M104 S0 ; turn off hotend
M140 S0 ; turn off bed
M106 S0 ; turn off fan
G1 Z20 F3000 ; move nozzle up 20mm
G90 ; absolute positioning
G0 X125 Y245 F3600 ; park nozzle at rear
M117 Finished! ; display message
[gcode_macro UNLOAD_FILAMENT]
gcode:
M83
G1 E10 F300
G1 E-780 F1800
M82
[gcode_macro LOAD_FILAMENT]
gcode:
M83
G1 E750 F1800
G1 E30 F300
G1 E15 F150
M82