=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2016.07.17 23:02:15 =~=~=~=~=~=~=~=~=~=~=~=
start
echo:Marlin 1.1.0-RCBugFix
echo: Last Updated: 2016-04-27 12:00 | Author: (none, default config)
Compiled: Jul 17 2016
echo: Free Memory: 2841  PlannerBufferBytes: 1232
echo:V24 stored settings retrieved (398 bytes)
echo:Steps per unit:
echo:  M92 X71.14 Y71.37 Z400.30 E94.29
echo:Maximum feedrates (mm/s):
echo:  M203 X500.00 Y500.00 Z5.00 E35.00
echo:Maximum Acceleration (mm/s2):
echo:  M201 X3000 Y3000 Z100 E10000
echo:Accelerations: P=printing, R=retract and T=travel
echo:  M204 P3000.00 R3000.00 T3000.00
echo:Advanced variables: S=Min feedrate (mm/s), T=Min travel feedrate (mm/s), B=minimum segment time (ms), X=maximum XY jerk (mm/s),  Z=maximum Z jerk (mm/s),  E=maximum E jerk (mm/s)
echo:  M205 S0.00 T0.00 B20000 X20.00 Z0.40 E5.00
echo:Home offset (mm)
echo:  M206 X0.00 Y0.00 Z0.00
echo:Material heatup parameters:
echo:  M145 S0 H180 B30 F0
echo:  M145 S1 H240 B85 F0
echo:PID settings:
echo:  M301 P22.20 I1.08 D114.00 C100.00 L20
echo:Filament settings: Disabled
echo:  M200 D3.00
echo:  M200 T1 D3.00
echo:  M200 D0
echo:Z-Probe Offset (mm):
echo:  M851 Z-1.82
echo:SD card ok
echo:SD card ok
echo:enqueueing "M23 shift~1.gco"
echo:enqueueing "M24"
echo:Now fresh file: shift~1.gco
File opened: 1605 Size: 15437
File selected
echo:enqueueing "M600"
echo:DEBUG:LEVELING
 T:105.9 /0.0 B:50.8 /80.0 T0:105.9 /0.0 T1:34.7 /0.0 B@:0 @:0 @0:0 @1:0 W:?
 T:105.3 /0.0 B:50.3 /80.0 T0:105.3 /0.0 T1:34.1 /0.0 B@:0 @:0 @0:0 @1:0 W:?
 T:104.9 /0.0 B:50.4 /80.0 T0:104.9 /0.0 T1:34.2 /0.0 B@:0 @:0 @0:0 @1:0 W:?
 T:104.5 /0.0 B:50.3 /80.0 T0:104.5 /0.0 T1:34.1 /0.0 B@:0 @:0 @0:0 @1:0 W:?
 T:104.0 /0.0 B:50.2 /80.0 T0:104.0 /0.0 T1:33.9 /0.0 B@:127 @:0 @0:0 @1:0 W:?
 T:103.7 /0.0 B:50.2 /80.0 T0:103.7 /0.0 T1:34.1 /0.0 B@:127 @:0 @0:0 @1:0 W:?
 T:103.3 /0.0 B:50.3 /80.0 T0:103.3 /0.0 T1:34.1 /0.0 B@:127 @:0 @0:0 @1:0 W:?
 T:102.9 /0.0 B:50.5 /80.0 T0:102.9 /0.0 T1:34.2 /0.0 B@:127 @:0 @0:0 @1:0 W:?
>>> gcode_G28
current_position=(0.00, 0.00, 0.00) : setup_for_endstop_or_probe_move
> endstops.enable(true)
Raise Z (before homing) to 5.00
do_blocking_move_to(0.00, 0.00, 5.00)
>>> homeaxis(0)
current_position=(0.00, 0.00, 5.00) : sync_plan_position
echo:busy: processing
current_position=(0.00, 0.00, 5.00) : sync_plan_position
current_position=(0.00, 0.00, 5.00) : > TRIGGER ENDSTOP
>>> set_axis_is_at_home(0)
For 88 axis:
 home_offset = 0.00
 position_shift = 0.00
 sw_endstop_min = 0.00
 sw_endstop_max = 190.00
> home_offset[88] = 0.00
current_position=(0.00, 0.00, 5.00) : 
<<< set_axis_is_at_home(0)
current_position=(0.00, 0.00, 5.00) : sync_plan_position
current_position=(0.00, 0.00, 5.00) : > AFTER set_axis_is_at_home
<<< homeaxis(0)
current_position=(0.00, 0.00, 5.00) : > homeX
>>> homeaxis(1)
current_position=(0.00, 0.00, 5.00) : sync_plan_position
echo:busy: processing
echo:busy: processing
current_position=(0.00, 0.00, 5.00) : sync_plan_position
current_position=(0.00, 0.00, 5.00) : > TRIGGER ENDSTOP
>>> set_axis_is_at_home(1)
For 89 axis:
 home_offset = 0.00
 position_shift = 0.00
 sw_endstop_min = 0.00
 sw_endstop_max = 190.00
> home_offset[89] = 0.00
current_position=(0.00, 0.00, 5.00) : 
<<< set_axis_is_at_home(1)
current_position=(0.00, 0.00, 5.00) : sync_plan_position
current_position=(0.00, 0.00, 5.00) : > AFTER set_axis_is_at_home
<<< homeaxis(1)
current_position=(0.00, 0.00, 5.00) : > homeY
>>> homeaxis(2)
> current_position=(0.00, 0.00, 5.00) : set_probe_deployed
deploy: 1do_probe_raise(15.00)
do_blocking_move_to(0.00, 0.00, 16.82)
echo:busy: processing
echo:busy: processing
do_blocking_move_to(0.00, 0.00, 16.82)
current_position=(0.00, 0.00, 0.00) : sync_plan_position
echo:busy: processing
current_position=(0.00, 0.00, 0.00) : sync_plan_position
echo:busy: processing
echo:busy: processing
current_position=(0.00, 0.00, 0.00) : > TRIGGER ENDSTOP
>>> set_axis_is_at_home(2)
For 90 axis:
 home_offset = 0.00
 position_shift = 0.00
 sw_endstop_min = 0.00
 sw_endstop_max = 180.00
> zprobe_zoffset = -1.82
> home_offset[90] = 0.00
current_position=(0.00, 0.00, 1.82) : 
<<< set_axis_is_at_home(2)
current_position=(0.00, 0.00, 1.82) : sync_plan_position
current_position=(0.00, 0.00, 1.82) : > AFTER set_axis_is_at_home
> current_position=(0.00, 0.00, 1.82) : set_probe_deployed
deploy: 0do_probe_raise(15.00)
do_blocking_move_to(0.00, 0.00, 16.82)
echo:busy: processing
echo:busy: processing
do_blocking_move_to(0.00, 0.00, 16.82)
<<< homeaxis(2)
current_position=(0.00, 0.00, 16.82) : > (home_all_axis || homeZ) > final
current_position=(0.00, 0.00, 16.82) : sync_plan_position
> endstops.not_homing()
current_position=(0.00, 0.00, 16.82) : clean_up_after_endstop_or_probe_move
<<< gcode_G28
X:0.00 Y:0.00 Z:16.82 E:0.00 Count X: 0 Y:0 Z:6733
>>> gcode_G29
current_position=(0.00, 0.00, 16.82) : 
G29 Auto Bed Leveling
corrected_position=(0.00, 0.00, 16.82) : BEFORE matrix.set_to_identity
current_position=(0.00, 0.00, 16.82) : BEFORE matrix.set_to_identity
uncorrected_position=(0.00, 0.00, 16.82) : AFTER matrix.set_to_identity
current_position=(0.00, 0.00, 16.82) : sync_plan_position
current_position=(0.00, 0.00, 16.82) : setup_for_endstop_or_probe_move
current_position=(0.00, 0.00, 16.82) : set_probe_deployed
deploy: 1do_probe_raise(15.00)
do_blocking_move_to(0.00, 0.00, 16.82)
do_blocking_move_to(0.00, 0.00, 16.82)
>>> probe_pt(30.00, 30.00, 1)
current_position=(0.00, 0.00, 16.82) : 
do_probe_raise(5.00)
> do_blocking_move_to_xy(0.00, 30.00)
do_blocking_move_to(0.00, 30.00, 16.82)
> current_position=(0.00, 30.00, 16.82) : set_probe_deployed
deploy: 1echo:busy: processing
echo:busy: processing
echo:busy: processing
current_position=(0.00, 30.00, 1.84) : run_z_probe
current_position=(0.00, 30.00, 1.84) : sync_plan_position
> do_probe_raise
do_probe_raise(5.00)
do_blocking_move_to(0.00, 30.00, 6.82)
<<< probe_pt
>>> probe_pt(95.00, 30.00, 1)
current_position=(0.00, 30.00, 6.82) : 
do_probe_raise(5.00)
> do_blocking_move_to_xy(65.00, 30.00)
do_blocking_move_to(65.00, 30.00, 6.82)
echo:busy: processing
> current_position=(65.00, 30.00, 6.82) : set_probe_deployed
deploy: 1echo:busy: processing
echo:busy: processing
current_position=(65.00, 30.00, 1.77) : run_z_probe
current_position=(65.00, 30.00, 1.77) : sync_plan_position
> do_probe_raise
do_probe_raise(5.00)
do_blocking_move_to(65.00, 30.00, 6.82)
<<< probe_pt
>>> probe_pt(160.00, 30.00, 1)
current_position=(65.00, 30.00, 6.82) : 
do_probe_raise(5.00)
> do_blocking_move_to_xy(130.00, 30.00)
do_blocking_move_to(130.00, 30.00, 6.82)
> current_position=(130.00, 30.00, 6.82) : set_probe_deployed
deploy: 1echo:busy: processing
echo:busy: processing
current_position=(130.00, 30.00, 1.96) : run_z_probe
current_position=(130.00, 30.00, 1.96) : sync_plan_position
> do_probe_raise
do_probe_raise(5.00)
do_blocking_move_to(130.00, 30.00, 6.82)
echo:busy: processing
<<< probe_pt
>>> probe_pt(160.00, 95.00, 1)
current_position=(130.00, 30.00, 6.82) : 
do_probe_raise(5.00)
> do_blocking_move_to_xy(130.00, 95.00)
do_blocking_move_to(130.00, 95.00, 6.82)
> current_position=(130.00, 95.00, 6.82) : set_probe_deployed
deploy: 1echo:busy: processing
echo:busy: processing
current_position=(130.00, 95.00, 1.91) : run_z_probe
current_position=(130.00, 95.00, 1.91) : sync_plan_position
> do_probe_raise
do_probe_raise(5.00)
do_blocking_move_to(130.00, 95.00, 6.82)
echo:busy: processing
<<< probe_pt
>>> probe_pt(95.00, 95.00, 1)
current_position=(130.00, 95.00, 6.82) : 
do_probe_raise(5.00)
> do_blocking_move_to_xy(65.00, 95.00)
do_blocking_move_to(65.00, 95.00, 6.82)
> current_position=(65.00, 95.00, 6.82) : set_probe_deployed
deploy: 1echo:busy: processing
echo:busy: processing
current_position=(65.00, 95.00, 1.75) : run_z_probe
current_position=(65.00, 95.00, 1.75) : sync_plan_position
> do_probe_raise
do_probe_raise(5.00)
do_blocking_move_to(65.00, 95.00, 6.82)
<<< probe_pt
>>> probe_pt(30.00, 95.00, 1)
current_position=(65.00, 95.00, 6.82) : 
do_probe_raise(5.00)
> do_blocking_move_to_xy(0.00, 95.00)
do_blocking_move_to(0.00, 95.00, 6.82)
echo:busy: processing
> current_position=(0.00, 95.00, 6.82) : set_probe_deployed
deploy: 1echo:busy: processing
echo:busy: processing
current_position=(0.00, 95.00, 2.00) : run_z_probe
current_position=(0.00, 95.00, 2.00) : sync_plan_position
> do_probe_raise
do_probe_raise(5.00)
do_blocking_move_to(0.00, 95.00, 6.82)
<<< probe_pt
>>> probe_pt(30.00, 160.00, 1)
current_position=(0.00, 95.00, 6.82) : 
do_probe_raise(5.00)
> do_blocking_move_to_xy(0.00, 160.00)
do_blocking_move_to(0.00, 160.00, 6.82)
> current_position=(0.00, 160.00, 6.82) : set_probe_deployed
deploy: 1echo:busy: processing
echo:busy: processing
current_position=(0.00, 160.00, 2.02) : run_z_probe
current_position=(0.00, 160.00, 2.02) : sync_plan_position
> do_probe_raise
do_probe_raise(5.00)
do_blocking_move_to(0.00, 160.00, 6.82)
echo:busy: processing
<<< probe_pt
>>> probe_pt(95.00, 160.00, 1)
current_position=(0.00, 160.00, 6.82) : 
do_probe_raise(5.00)
> do_blocking_move_to_xy(65.00, 160.00)
do_blocking_move_to(65.00, 160.00, 6.82)
> current_position=(65.00, 160.00, 6.82) : set_probe_deployed
deploy: 1echo:busy: processing
echo:busy: processing
current_position=(65.00, 160.00, 1.64) : run_z_probe
current_position=(65.00, 160.00, 1.64) : sync_plan_position
> do_probe_raise
do_probe_raise(5.00)
do_blocking_move_to(65.00, 160.00, 6.82)
echo:busy: processing
<<< probe_pt
>>> probe_pt(160.00, 160.00, 1)
current_position=(65.00, 160.00, 6.82) : 
do_probe_raise(5.00)
> do_blocking_move_to_xy(130.00, 160.00)
do_blocking_move_to(130.00, 160.00, 6.82)
> current_position=(130.00, 160.00, 6.82) : set_probe_deployed
deploy: 1echo:busy: processing
echo:busy: processing
current_position=(130.00, 160.00, 1.82) : run_z_probe
current_position=(130.00, 160.00, 1.82) : sync_plan_position
> do_probe_raise
do_probe_raise(5.00)
do_blocking_move_to(130.00, 160.00, 6.82)
echo:busy: processing
<<< probe_pt
current_position=(130.00, 160.00, 6.82) : set_probe_deployed
deploy: 0do_probe_raise(15.00)
do_blocking_move_to(130.00, 160.00, 16.82)
echo:busy: processing
do_blocking_move_to(130.00, 160.00, 16.82)
current_position=(130.00, 160.00, 16.82) : clean_up_after_endstop_or_probe_move
current_position=(130.00, 160.00, 16.82) : > probing complete
Eqn coefficients: a: -0.00046119 b: -0.00023700 d: 1.92299127
uncorrected_position=(130.00, 160.00, 16.82) : >>> set_bed_level_equation_lsq
current_position=(130.00, 160.00, 16.82) : >>> set_bed_level_equation_lsq
corrected_position=(129.99, 159.99, 16.92) : <<< set_bed_level_equation_lsq
current_position=(129.99, 159.99, 16.92) : sync_plan_position


Bed Level Correction Matrix:
+1.000000 +0.000000 -0.000461 
-0.000000 +1.000000 -0.000237 
+0.000461 +0.000237 +1.000000 
> BEFORE apply_rotation_xyz > stepper_z = 16.82 ... z_tmp  = 16.92
> AFTER apply_rotation_xyz > z_tmp  = 16.81
current_position=(129.99, 159.99, 16.90) : sync_plan_position
current_position=(129.99, 159.99, 16.90) : > corrected Z in G29
<<< gcode_G29
X:129.99 Y:159.99 Z:16.90 E:0.00 Count X: 9248 Y:11419 Z:6727
 T:166.0 /238.0 B:58.7 /80.0 T0:80.3 /0.0 T1:166.0 /238.0 B@:127 @:127 @0:0 @1:127 W:?
 T:167.4 /238.0 B:58.7 /80.0 T0:80.1 /0.0 T1:167.4 /238.0 B@:127 @:127 @0:0 @1:127 W:?
 T:168.6 /238.0 B:58.9 /80.0 T0:80.0 /0.0 T1:168.6 /238.0 B@:127 @:127 @0:0 @1:127 W:?
 T:169.9 /238.0 B:59.0 /80.0 T0:79.7 /0.0 T1:169.9 /238.0 B@:127 @:127 @0:0 @1:127 W:?
 T:171.7 /238.0 B:59.0 /80.0 T0:79.5 /0.0 T1:171.7 /238.0 B@:127 @:127 @0:0 @1:127 W:?
 T:173.2 /238.0 B:59.2 /80.0 T0:79.2 /0.0 T1:173.2 /238.0 B@:127 @:127 @0:0 @1:127 W:?
 T:174.6 /238.0 B:59.3 /80.0 T0:79.0 /0.0 T1:174.6 /238.0 B@:127 @:127 @0:0 @1:127 W:?
 T:175.9 /238.0 B:59.4 /80.0 T0:78.8 /0.0 T1:175.9 /238.0 B@:127 @:127 @0:0 @1:127 W:?
 T:177.3 /238.0 B:59.5 /80.0 T0:78.6 /0.0 T1:177.3 /238.0 B@:127 @:127 @0:0 @1:127 W:?
 T:178.6 /238.0 B:59.6 /80.0 T0:78.3 /0.0 T1:178.6 /238.0 B@:127 @:127 @0:0 @1:127 W:?
 T:179.9 /238.0 B:59.7 /80.0 T0:78.2 /0.0 T1:179.9 /238.0 B@:127 @:127 @0:0 @1:127 W:?
 T:181.3 /238.0 B:59.7 /80.0 T0:77.9 /0.0 T1:181.3 /238.0 B@:127 @:127 @0:0 @1:127 W:?
 T:182.6 /238.0 B:59.8 /80.0 T0:77.7 /0.0 T1:182.6 /238.0 B@:127 @:127 @0:0 @1:127 W:?
 T:184.0 /238.0 B:60.0 /80.0 T0:77.5 /0.0 T1:184.0 /238.0 B@:127 @:127 @0:0 @1:127 W:?
 T:185.4 /238.0 B:60.0 /80.0 T0:77.3 /0.0 T1:185.4 /238.0 B@:127 @:127 @0:0 @1:127 W:?
 T:186.8 /238.0 B:60.2 /80.0 T0:77.1 /0.0 T1:186.8 /238.0 B@:127 @:127 @0:0 @1:127 W:?
 T:188.2 /238.0 B:60.2 /80.0 T0:76.9 /0.0 T1:188.2 /238.0 B@:127 @:127 @0:0 @1:127 W:?
 T:189.4 /238.0 B:60.3 /80.0 T0:76.7 /0.0 T1:189.4 /238.0 B@:127 @:127 @0:0 @1:127 W:?
 T:190.6 /238.0 B:60.4 /80.0 T0:76.5 /0.0 T1:190.6 /238.0 B@:127 @:127 @0:0 @1:127 W:?
 T:191.8 /238.0 B:60.5 /80.0 T0:76.4 /0.0 T1:191.8 /238.0 B@:127 @:127 @0:0 @1:127 W:?
 T:193.1 /238.0 B:60.6 /80.0 T0:76.1 /0.0 T1:193.1 /238.0 B@:127 @:127 @0:0 @1:127 W:?
 T:194.4 /238.0 B:60.7 /80.0 T0:75.9 /0.0 T1:194.4 /238.0 B@:127 @:127 @0:0 @1:127 W:?
 T:195.5 /238.0 B:60.8 /80.0 T0:75.7 /0.0 T1:195.5 /238.0 B@:127 @:127 @0:0 @1:127 W:?
 T:196.7 /238.0 B:60.9 /80.0 T0:75.6 /0.0 T1:196.7 /238.0 B@:127 @:127 @0:0 @1:127 W:?
 T:197.8 /238.0 B:61.0 /80.0 T0:75.4 /0.0 T1:197.8 /238.0 B@:127 @:127 @0:0 @1:127 W:?
 T:198.9 /238.0 B:61.1 /80.0 T0:75.2 /0.0 T1:198.9 /238.0 B@:127 @:127 @0:0 @1:127 W:?
 T:199.8 /238.0 B:61.2 /80.0 T0:75.0 /0.0 T1:199.8 /238.0 B@:127 @:127 @0:0 @1:127 W:?
 T:201.4 /238.0 B:61.3 /80.0 T0:74.8 /0.0 T1:201.4 /238.0 B@:127 @:127 @0:0 @1:127 W:?
 T:202.7 /238.0 B:61.4 /80.0 T0:74.7 /0.0 T1:202.7 /238.0 B@:127 @:127 @0:0 @1:127 W:?
 T:204.0 /238.0 B:61.5 /80.0 T0:74.5 /0.0 T1:204.0 /238.0 B@:127 @:127 @0:0 @1:127 W:?
 T:205.1 /238.0 B:61.6 /80.0 T0:74.3 /0.0 T1:205.1 /238.0 B@:127 @:127 @0:0 @1:127 W:?
 T:206.1 /238.0 B:61.6 /80.0 T0:74.1 /0.0 T1:206.1 /238.0 B@:127 @:127 @0:0 @1:127 W:?
 T:207.6 /238.0 B:61.7 /80.0 T0:74.0 /0.0 T1:207.6 /238.0 B@:127 @:127 @0:0 @1:127 W:?
 T:208.6 /238.0 B:61.8 /80.0 T0:73.8 /0.0 T1:208.6 /238.0 B@:127 @:127 @0:0 @1:127 W:?
 T:209.6 /238.0 B:61.9 /80.0 T0:73.7 /0.0 T1:209.6 /238.0 B@:127 @:127 @0:0 @1:127 W:?
 T:210.7 /238.0 B:62.0 /80.0 T0:73.5 /0.0 T1:210.7 /238.0 B@:127 @:127 @0:0 @1:127 W:?
 T:211.9 /238.0 B:62.1 /80.0 T0:73.3 /0.0 T1:211.9 /238.0 B@:127 @:127 @0:0 @1:127 W:?
 T:213.4 /238.0 B:62.2 /80.0 T0:73.2 /0.0 T1:213.4 /238.0 B@:127 @:127 @0:0 @1:127 W:?
 T:214.2 /238.0 B:62.3 /80.0 T0:73.0 /0.0 T1:214.2 /238.0 B@:127 @:127 @0:0 @1:127 W:?
 T:215.7 /238.0 B:62.4 /80.0 T0:72.8 /0.0 T1:215.7 /238.0 B@:127 @:127 @0:0 @1:127 W:?
 T:216.7 /238.0 B:62.5 /80.0 T0:72.7 /0.0 T1:216.7 /238.0 B@:127 @:127 @0:0 @1:127 W:?
 T:217.5 /238.0 B:62.5 /80.0 T0:72.5 /0.0 T1:217.5 /238.0 B@:127 @:127 @0:0 @1:127 W:?
 T:218.5 /238.0 B:62.7 /80.0 T0:72.4 /0.0 T1:218.5 /238.0 B@:127 @:127 @0:0 @1:127 W:?
 T:219.7 /238.0 B:62.7 /80.0 T0:72.3 /0.0 T1:219.7 /238.0 B@:127 @:127 @0:0 @1:127 W:?
 T:220.6 /238.0 B:62.8 /80.0 T0:72.1 /0.0 T1:220.6 /238.0 B@:127 @:127 @0:0 @1:127 W:?
 T:221.5 /238.0 B:62.9 /80.0 T0:72.0 /0.0 T1:221.5 /238.0 B@:127 @:127 @0:0 @1:127 W:?
 T:222.8 /238.0 B:63.0 /80.0 T0:71.8 /0.0 T1:222.8 /238.0 B@:127 @:127 @0:0 @1:127 W:?
 T:223.6 /238.0 B:63.2 /80.0 T0:71.7 /0.0 T1:223.6 /238.0 B@:127 @:127 @0:0 @1:127 W:?
 T:224.7 /238.0 B:63.2 /80.0 T0:71.5 /0.0 T1:224.7 /238.0 B@:127 @:127 @0:0 @1:127 W:?
 T:225.8 /238.0 B:63.3 /80.0 T0:71.4 /0.0 T1:225.8 /238.0 B@:127 @:127 @0:0 @1:127 W:?
 T:226.9 /238.0 B:63.4 /80.0 T0:71.2 /0.0 T1:226.9 /238.0 B@:127 @:127 @0:0 @1:127 W:?
 T:227.6 /238.0 B:63.5 /80.0 T0:71.1 /0.0 T1:227.6 /238.0 B@:127 @:127 @0:0 @1:127 W:?
 T:228.7 /238.0 B:63.6 /80.0 T0:70.9 /0.0 T1:228.7 /238.0 B@:127 @:51 @0:0 @1:51 W:?
 T:229.3 /238.0 B:63.7 /80.0 T0:70.8 /0.0 T1:229.3 /238.0 B@:127 @:54 @0:0 @1:54 W:?
 T:230.2 /238.0 B:63.8 /80.0 T0:70.6 /0.0 T1:230.2 /238.0 B@:127 @:48 @0:0 @1:48 W:?
 T:231.1 /238.0 B:63.9 /80.0 T0:70.5 /0.0 T1:231.1 /238.0 B@:127 @:43 @0:0 @1:43 W:?
 T:231.7 /238.0 B:64.0 /80.0 T0:70.4 /0.0 T1:231.7 /238.0 B@:127 @:43 @0:0 @1:43 W:?
 T:232.0 /238.0 B:64.1 /80.0 T0:70.3 /0.0 T1:232.0 /238.0 B@:127 @:49 @0:0 @1:49 W:?
 T:232.3 /238.0 B:64.1 /80.0 T0:70.1 /0.0 T1:232.3 /238.0 B@:127 @:55 @0:0 @1:55 W:?
 T:232.3 /238.0 B:64.3 /80.0 T0:70.0 /0.0 T1:232.3 /238.0 B@:127 @:64 @0:0 @1:64 W:?
 T:232.3 /238.0 B:64.4 /80.0 T0:69.9 /0.0 T1:232.3 /238.0 B@:127 @:75 @0:0 @1:75 W:?
 T:232.1 /238.0 B:64.5 /80.0 T0:69.8 /0.0 T1:232.1 /238.0 B@:127 @:86 @0:0 @1:86 W:?
 T:232.0 /238.0 B:64.5 /80.0 T0:69.6 /0.0 T1:232.0 /238.0 B@:127 @:95 @0:0 @1:95 W:?
 T:231.5 /238.0 B:64.6 /80.0 T0:69.4 /0.0 T1:231.5 /238.0 B@:127 @:114 @0:0 @1:114 W:?
 T:231.2 /238.0 B:64.7 /80.0 T0:69.3 /0.0 T1:231.2 /238.0 B@:127 @:126 @0:0 @1:126 W:?
 T:231.6 /238.0 B:64.8 /80.0 T0:69.1 /0.0 T1:231.6 /238.0 B@:127 @:116 @0:0 @1:116 W:?
 T:231.8 /238.0 B:64.9 /80.0 T0:69.0 /0.0 T1:231.8 /238.0 B@:127 @:116 @0:0 @1:116 W:?
 T:232.0 /238.0 B:65.0 /80.0 T0:68.9 /0.0 T1:232.0 /238.0 B@:127 @:115 @0:0 @1:115 W:?
 T:232.3 /238.0 B:65.1 /80.0 T0:68.7 /0.0 T1:232.3 /238.0 B@:127 @:112 @0:0 @1:112 W:?
 T:233.0 /238.0 B:65.1 /80.0 T0:68.6 /0.0 T1:233.0 /238.0 B@:127 @:99 @0:0 @1:99 W:?
 T:233.6 /238.0 B:65.3 /80.0 T0:68.5 /0.0 T1:233.6 /238.0 B@:127 @:92 @0:0 @1:92 W:?
 T:233.7 /238.0 B:65.3 /80.0 T0:68.4 /0.0 T1:233.7 /238.0 B@:127 @:97 @0:0 @1:97 W:?
 T:234.3 /238.0 B:65.4 /80.0 T0:68.3 /0.0 T1:234.3 /238.0 B@:127 @:87 @0:0 @1:87 W:?
 T:234.8 /238.0 B:65.5 /80.0 T0:68.1 /0.0 T1:234.8 /238.0 B@:127 @:85 @0:0 @1:85 W:?
 T:234.9 /238.0 B:65.6 /80.0 T0:68.0 /0.0 T1:234.9 /238.0 B@:127 @:88 @0:0 @1:88 W:?
 T:235.6 /238.0 B:65.8 /80.0 T0:67.9 /0.0 T1:235.6 /238.0 B@:127 @:77 @0:0 @1:77 W:?
 T:236.3 /238.0 B:65.8 /80.0 T0:67.7 /0.0 T1:236.3 /238.0 B@:127 @:69 @0:0 @1:69 W:?
 T:236.5 /238.0 B:65.9 /80.0 T0:67.7 /0.0 T1:236.5 /238.0 B@:127 @:69 @0:0 @1:69 W:?
 T:236.6 /238.0 B:66.0 /80.0 T0:67.5 /0.0 T1:236.6 /238.0 B@:127 @:73 @0:0 @1:73 W:?
 T:236.9 /238.0 B:66.1 /80.0 T0:67.4 /0.0 T1:236.9 /238.0 B@:127 @:71 @0:0 @1:71 W:9
 T:237.2 /238.0 B:66.2 /80.0 T0:67.2 /0.0 T1:237.2 /238.0 B@:127 @:68 @0:0 @1:68 W:8
 T:236.8 /238.0 B:66.3 /80.0 T0:67.2 /0.0 T1:236.8 /238.0 B@:127 @:82 @0:0 @1:82 W:7
 T:237.1 /238.0 B:66.4 /80.0 T0:67.0 /0.0 T1:237.1 /238.0 B@:127 @:78 @0:0 @1:78 W:6
 T:237.1 /238.0 B:66.5 /80.0 T0:67.0 /0.0 T1:237.1 /238.0 B@:127 @:81 @0:0 @1:81 W:5
 T:237.0 /238.0 B:66.5 /80.0 T0:66.8 /0.0 T1:237.0 /238.0 B@:127 @:87 @0:0 @1:87 W:4
 T:237.0 /238.0 B:66.6 /80.0 T0:66.6 /0.0 T1:237.0 /238.0 B@:127 @:89 @0:0 @1:89 W:3
 T:237.0 /238.0 B:66.7 /80.0 T0:66.5 /0.0 T1:237.0 /238.0 B@:127 @:88 @0:0 @1:88 W:2
 T:237.3 /238.0 B:66.9 /80.0 T0:66.4 /0.0 T1:237.3 /238.0 B@:127 @:82 @0:0 @1:82 W:1
 T:237.2 /238.0 B:67.0 /80.0 T0:66.3 /0.0 T1:237.2 /238.0 B@:127 @:87 @0:0 @1:87 W:0
>>> gcode_T
current_position=(129.99, 159.99, 5.00) : BEFORE
tmp_offset_vec x: -30.399999 y: 0.600000 z: 0.000000
act_offset_vec x: 0.000000 y: 0.000000 z: 0.000000
offset_vec (BEFORE) x: -30.399999 y: 0.600000 z: 0.000000
offset_vec (AFTER) x: -30.399995 y: 0.600003 z: -0.013878
Offset Tool XY by { -30.40, -30.40 }
For 88 axis:
 home_offset = 0.00
 position_shift = -30.40
 sw_endstop_min = -30.40
 sw_endstop_max = 159.60
For 89 axis:
 home_offset = 0.00
 position_shift = 0.60
 sw_endstop_min = 0.60
 sw_endstop_max = 190.60
current_position=(99.59, 160.59, 4.99) : Sync After Toolchange
current_position=(99.59, 160.59, 4.99) : sync_plan_position
destination=(129.99, 159.99, 5.00) : Move back
current_position=(129.99, 159.99, 5.00) : AFTER
<<< gcode_T
echo:Active Extruder: 1
Setting Print and Travel Acceleration: 800.00
Setting Print and Travel Acceleration: 2200.00
Setting Print and Travel Acceleration: 800.00
Setting Print and Travel Acceleration: 2200.00
Setting Print and Travel Acceleration: 800.00
Setting Print and Travel Acceleration: 2200.00
Setting Print and Travel Acceleration: 800.00
Setting Print and Travel Acceleration: 2200.00
Setting Print and Travel Acceleration: 800.00
Setting Print and Travel Acceleration: 2200.00
Setting Print and Travel Acceleration: 800.00
Setting Print and Travel Acceleration: 2200.00
Setting Print and Travel Acceleration: 3000.00
Setting Print and Travel Acceleration: 2200.00
Setting Print and Travel Acceleration: 3000.00
Setting Print and Travel Acceleration: 2200.00
Setting Print and Travel Acceleration: 3000.00
Setting Print and Travel Acceleration: 2200.00
Setting Print and Travel Acceleration: 800.00
Setting Print and Travel Acceleration: 2200.00
Setting Print and Travel Acceleration: 3000.00
Setting Print and Travel Acceleration: 2200.00
Setting Print and Travel Acceleration: 3000.00
Setting Print and Travel Acceleration: 2200.00
Setting Print and Travel Acceleration: 3000.00
Setting Print and Travel Acceleration: 2200.00
Setting Print and Travel Acceleration: 800.00
Setting Print and Travel Acceleration: 2200.00
Done printing file
echo:enqueueing "M84 X Y Z E"
echo:enqueueing "M31"
>>> gcode_G28
current_position=(86.70, 102.99, 0.70) : setup_for_endstop_or_probe_move
> endstops.enable(true)
Raise Z (before homing) to 5.00
do_blocking_move_to(86.70, 102.99, 5.00)
>>> homeaxis(0)
current_position=(0.00, 102.99, 5.00) : sync_plan_position
echo:busy: processing
current_position=(0.00, 102.99, 5.00) : sync_plan_position
current_position=(0.00, 102.99, 5.00) : > TRIGGER ENDSTOP
>>> set_axis_is_at_home(0)
For 88 axis:
 home_offset = 0.00
 position_shift = 0.00
 sw_endstop_min = 0.00
 sw_endstop_max = 190.00
> home_offset[88] = 0.00
current_position=(0.00, 102.99, 5.00) : 
<<< set_axis_is_at_home(0)
current_position=(0.00, 102.99, 5.00) : sync_plan_position
current_position=(0.00, 102.99, 5.00) : > AFTER set_axis_is_at_home
<<< homeaxis(0)
current_position=(0.00, 102.99, 5.00) : > homeX
current_position=(0.00, 102.99, 5.00) : sync_plan_position
> endstops.not_homing()
current_position=(0.00, 102.99, 5.00) : clean_up_after_endstop_or_probe_move
<<< gcode_G28
X:0.00 Y:102.99 Z:5.00 E:0.00 Count X: 0 Y:7351 Z:2002
echo:Print time 0h 4m 11s
echo:enqueueing "M23 shift~1.gco"
echo:enqueueing "M24"
echo:Now fresh file: shift~1.gco
File opened: 1797 Size: 15437
File selected
echo:DEBUG:LEVELING
 T:217.7 /0.0 B:68.8 /80.0 T0:57.5 /0.0 T1:217.7 /0.0 B@:0 @:0 @0:0 @1:0 W:?
 T:216.9 /0.0 B:69.0 /80.0 T0:57.7 /0.0 T1:216.9 /0.0 B@:0 @:0 @0:0 @1:0 W:?
 T:215.4 /0.0 B:68.9 /80.0 T0:57.7 /0.0 T1:215.4 /0.0 B@:0 @:0 @0:0 @1:0 W:?
 T:214.3 /0.0 B:68.8 /80.0 T0:57.6 /0.0 T1:214.3 /0.0 B@:0 @:0 @0:0 @1:0 W:?
 T:213.3 /0.0 B:68.7 /80.0 T0:57.6 /0.0 T1:213.3 /0.0 B@:0 @:0 @0:0 @1:0 W:?
 T:211.9 /0.0 B:68.6 /80.0 T0:57.5 /0.0 T1:211.9 /0.0 B@:127 @:0 @0:0 @1:0 W:?
 T:210.5 /0.0 B:68.6 /80.0 T0:57.5 /0.0 T1:210.5 /0.0 B@:127 @:0 @0:0 @1:0 W:?
 T:209.6 /0.0 B:68.4 /80.0 T0:57.2 /0.0 T1:209.6 /0.0 B@:127 @:0 @0:0 @1:0 W:?
 T:208.3 /0.0 B:68.6 /80.0 T0:57.3 /0.0 T1:208.3 /0.0 B@:127 @:0 @0:0 @1:0 W:?
 T:207.2 /0.0 B:68.7 /80.0 T0:57.2 /0.0 T1:207.2 /0.0 B@:127 @:0 @0:0 @1:0 W:?
>>> gcode_G28
current_position=(0.00, 102.99, 5.00) : setup_for_endstop_or_probe_move
> endstops.enable(true)
>>> homeaxis(0)
current_position=(0.00, 102.99, 5.00) : sync_plan_position
current_position=(0.00, 102.99, 5.00) : sync_plan_position
current_position=(0.00, 102.99, 5.00) : > TRIGGER ENDSTOP
>>> set_axis_is_at_home(0)
For 88 axis:
 home_offset = 0.00
 position_shift = 0.00
 sw_endstop_min = 0.00
 sw_endstop_max = 190.00
> home_offset[88] = 0.00
current_position=(0.00, 102.99, 5.00) : 
<<< set_axis_is_at_home(0)
current_position=(0.00, 102.99, 5.00) : sync_plan_position
current_position=(0.00, 102.99, 5.00) : > AFTER set_axis_is_at_home
<<< homeaxis(0)
current_position=(0.00, 102.99, 5.00) : > homeX
>>> homeaxis(1)
current_position=(0.00, 0.00, 5.00) : sync_plan_position
echo:busy: processing
current_position=(0.00, 0.00, 5.00) : sync_plan_position
current_position=(0.00, 0.00, 5.00) : > TRIGGER ENDSTOP
>>> set_axis_is_at_home(1)
For 89 axis:
 home_offset = 0.00
 position_shift = 0.00
 sw_endstop_min = 0.00
 sw_endstop_max = 190.00
> home_offset[89] = 0.00
current_position=(0.00, 0.00, 5.00) : 
<<< set_axis_is_at_home(1)
current_position=(0.00, 0.00, 5.00) : sync_plan_position
current_position=(0.00, 0.00, 5.00) : > AFTER set_axis_is_at_home
<<< homeaxis(1)
current_position=(0.00, 0.00, 5.00) : > homeY
>>> homeaxis(2)
> current_position=(0.00, 0.00, 5.00) : set_probe_deployed
deploy: 1do_probe_raise(15.00)
do_blocking_move_to(0.00, 0.00, 16.82)
echo:busy: processing
do_blocking_move_to(0.00, 0.00, 16.82)
current_position=(0.00, 0.00, 0.00) : sync_plan_position
echo:busy: processing
echo:busy: processing
current_position=(0.00, 0.00, 0.00) : sync_plan_position
echo:busy: processing
current_position=(0.00, 0.00, 0.00) : > TRIGGER ENDSTOP
>>> set_axis_is_at_home(2)
For 90 axis:
 home_offset = 0.00
 position_shift = 0.00
 sw_endstop_min = 0.00
 sw_endstop_max = 180.00
> zprobe_zoffset = -1.82
> home_offset[90] = 0.00
current_position=(0.00, 0.00, 1.82) : 
<<< set_axis_is_at_home(2)
current_position=(0.00, 0.00, 1.82) : sync_plan_position
current_position=(0.00, 0.00, 1.82) : > AFTER set_axis_is_at_home
> current_position=(0.00, 0.00, 1.82) : set_probe_deployed
deploy: 0do_probe_raise(15.00)
do_blocking_move_to(0.00, 0.00, 16.82)
echo:busy: processing
echo:busy: processing
do_blocking_move_to(0.00, 0.00, 16.82)
<<< homeaxis(2)
current_position=(0.00, 0.00, 16.82) : > (home_all_axis || homeZ) > final
current_position=(0.00, 0.00, 16.82) : sync_plan_position
> endstops.not_homing()
current_position=(0.00, 0.00, 16.82) : clean_up_after_endstop_or_probe_move
<<< gcode_G28
X:0.00 Y:0.00 Z:16.82 E:0.00 Count X: 0 Y:0 Z:6733
>>> gcode_G29
current_position=(0.00, 0.00, 16.82) : 
G29 Auto Bed Leveling
corrected_position=(0.00, 0.00, 16.82) : BEFORE matrix.set_to_identity
current_position=(0.00, 0.00, 16.82) : BEFORE matrix.set_to_identity
uncorrected_position=(0.00, 0.00, 16.82) : AFTER matrix.set_to_identity
current_position=(0.00, 0.00, 16.82) : sync_plan_position
current_position=(0.00, 0.00, 16.82) : setup_for_endstop_or_probe_move
current_position=(0.00, 0.00, 16.82) : set_probe_deployed
deploy: 1do_probe_raise(15.00)
do_blocking_move_to(0.00, 0.00, 16.82)
do_blocking_move_to(0.00, 0.00, 16.82)
>>> probe_pt(30.00, 30.00, 1)
current_position=(0.00, 0.00, 16.82) : 
do_probe_raise(5.00)
> do_blocking_move_to_xy(0.00, 30.00)
do_blocking_move_to(0.00, 30.00, 16.82)
> current_position=(0.00, 30.00, 16.82) : set_probe_deployed
deploy: 1echo:busy: processing
echo:busy: processing
echo:busy: processing
current_position=(0.00, 30.00, 1.83) : run_z_probe
current_position=(0.00, 30.00, 1.83) : sync_plan_position
> do_probe_raise
do_probe_raise(5.00)
do_blocking_move_to(0.00, 30.00, 6.82)
<<< probe_pt
>>> probe_pt(95.00, 30.00, 1)
current_position=(0.00, 30.00, 6.82) : 
do_probe_raise(5.00)
> do_blocking_move_to_xy(65.00, 30.00)
do_blocking_move_to(65.00, 30.00, 6.82)
echo:busy: processing
> current_position=(65.00, 30.00, 6.82) : set_probe_deployed
deploy: 1echo:busy: processing
echo:busy: processing
current_position=(65.00, 30.00, 1.78) : run_z_probe
current_position=(65.00, 30.00, 1.78) : sync_plan_position
> do_probe_raise
do_probe_raise(5.00)
do_blocking_move_to(65.00, 30.00, 6.82)
<<< probe_pt
>>> probe_pt(160.00, 30.00, 1)
current_position=(65.00, 30.00, 6.82) : 
do_probe_raise(5.00)
> do_blocking_move_to_xy(130.00, 30.00)
do_blocking_move_to(130.00, 30.00, 6.82)
> current_position=(130.00, 30.00, 6.82) : set_probe_deployed
deploy: 1echo:busy: processing
echo:busy: processing
current_position=(130.00, 30.00, 1.97) : run_z_probe
current_position=(130.00, 30.00, 1.97) : sync_plan_position
> do_probe_raise
do_probe_raise(5.00)
do_blocking_move_to(130.00, 30.00, 6.82)
echo:busy: processing
<<< probe_pt
>>> probe_pt(160.00, 95.00, 1)
current_position=(130.00, 30.00, 6.82) : 
do_probe_raise(5.00)
> do_blocking_move_to_xy(130.00, 95.00)
do_blocking_move_to(130.00, 95.00, 6.82)
> current_position=(130.00, 95.00, 6.82) : set_probe_deployed
deploy: 1echo:busy: processing
echo:busy: processing
current_position=(130.00, 95.00, 1.92) : run_z_probe
current_position=(130.00, 95.00, 1.92) : sync_plan_position
> do_probe_raise
do_probe_raise(5.00)
do_blocking_move_to(130.00, 95.00, 6.82)
echo:busy: processing
<<< probe_pt
>>> probe_pt(95.00, 95.00, 1)
current_position=(130.00, 95.00, 6.82) : 
do_probe_raise(5.00)
> do_blocking_move_to_xy(65.00, 95.00)
do_blocking_move_to(65.00, 95.00, 6.82)
> current_position=(65.00, 95.00, 6.82) : set_probe_deployed
deploy: 1echo:busy: processing
echo:busy: processing
current_position=(65.00, 95.00, 1.76) : run_z_probe
current_position=(65.00, 95.00, 1.76) : sync_plan_position
> do_probe_raise
do_probe_raise(5.00)
do_blocking_move_to(65.00, 95.00, 6.82)
echo:busy: processing
<<< probe_pt
>>> probe_pt(30.00, 95.00, 1)
current_position=(65.00, 95.00, 6.82) : 
do_probe_raise(5.00)
> do_blocking_move_to_xy(0.00, 95.00)
do_blocking_move_to(0.00, 95.00, 6.82)
> current_position=(0.00, 95.00, 6.82) : set_probe_deployed
deploy: 1echo:busy: processing
echo:busy: processing
current_position=(0.00, 95.00, 1.99) : run_z_probe
current_position=(0.00, 95.00, 1.99) : sync_plan_position
> do_probe_raise
do_probe_raise(5.00)
do_blocking_move_to(0.00, 95.00, 6.82)
<<< probe_pt
>>> probe_pt(30.00, 160.00, 1)
current_position=(0.00, 95.00, 6.82) : 
do_probe_raise(5.00)
> do_blocking_move_to_xy(0.00, 160.00)
do_blocking_move_to(0.00, 160.00, 6.82)
echo:busy: processing
> current_position=(0.00, 160.00, 6.82) : set_probe_deployed
deploy: 1echo:busy: processing
current_position=(0.00, 160.00, 2.03) : run_z_probe
current_position=(0.00, 160.00, 2.03) : sync_plan_position
> do_probe_raise
do_probe_raise(5.00)
do_blocking_move_to(0.00, 160.00, 6.82)
echo:busy: processing
<<< probe_pt
>>> probe_pt(95.00, 160.00, 1)
current_position=(0.00, 160.00, 6.82) : 
do_probe_raise(5.00)
> do_blocking_move_to_xy(65.00, 160.00)
do_blocking_move_to(65.00, 160.00, 6.82)
> current_position=(65.00, 160.00, 6.82) : set_probe_deployed
deploy: 1echo:busy: processing
echo:busy: processing
current_position=(65.00, 160.00, 1.67) : run_z_probe
current_position=(65.00, 160.00, 1.67) : sync_plan_position
> do_probe_raise
do_probe_raise(5.00)
do_blocking_move_to(65.00, 160.00, 6.82)
echo:busy: processing
<<< probe_pt
>>> probe_pt(160.00, 160.00, 1)
current_position=(65.00, 160.00, 6.82) : 
do_probe_raise(5.00)
> do_blocking_move_to_xy(130.00, 160.00)
do_blocking_move_to(130.00, 160.00, 6.82)
> current_position=(130.00, 160.00, 6.82) : set_probe_deployed
deploy: 1echo:busy: processing
echo:busy: processing
current_position=(130.00, 160.00, 1.83) : run_z_probe
current_position=(130.00, 160.00, 1.83) : sync_plan_position
> do_probe_raise
do_probe_raise(5.00)
do_blocking_move_to(130.00, 160.00, 6.82)
echo:busy: processing
<<< probe_pt
current_position=(130.00, 160.00, 6.82) : set_probe_deployed
deploy: 0do_probe_raise(15.00)
do_blocking_move_to(130.00, 160.00, 16.82)
echo:busy: processing
do_blocking_move_to(130.00, 160.00, 16.82)
current_position=(130.00, 160.00, 16.82) : clean_up_after_endstop_or_probe_move
current_position=(130.00, 160.00, 16.82) : > probing complete
Eqn coefficients: a: -0.00034590 b: -0.00016013 d: 1.91139736
uncorrected_position=(130.00, 160.00, 16.82) : >>> set_bed_level_equation_lsq
current_position=(130.00, 160.00, 16.82) : >>> set_bed_level_equation_lsq
corrected_position=(129.99, 159.99, 16.89) : <<< set_bed_level_equation_lsq
current_position=(129.99, 159.99, 16.89) : sync_plan_position


Bed Level Correction Matrix:
+1.000000 +0.000000 -0.000346 
-0.000000 +1.000000 -0.000160 
+0.000346 +0.000160 +1.000000 
> BEFORE apply_rotation_xyz > stepper_z = 16.82 ... z_tmp  = 16.89
> AFTER apply_rotation_xyz > z_tmp  = 16.81
current_position=(129.99, 159.99, 16.88) : sync_plan_position
current_position=(129.99, 159.99, 16.88) : > corrected Z in G29
<<< gcode_G29
X:129.99 Y:159.99 Z:16.88 E:0.00 Count X: 9248 Y:11419 Z:6729
>>> gcode_T
current_position=(129.99, 159.99, 5.00) : BEFORE
echo:busy: processing
current_position=(129.99, 159.99, 5.00) : AFTER
<<< gcode_T
echo:Active Extruder: 1
Setting Print and Travel Acceleration: 800.00
Setting Print and Travel Acceleration: 2200.00
Setting Print and Travel Acceleration: 800.00
Setting Print and Travel Acceleration: 2200.00
Setting Print and Travel Acceleration: 800.00
Setting Print and Travel Acceleration: 2200.00
Setting Print and Travel Acceleration: 800.00
Setting Print and Travel Acceleration: 2200.00
Setting Print and Travel Acceleration: 800.00
Setting Print and Travel Acceleration: 2200.00
Setting Print and Travel Acceleration: 800.00
Setting Print and Travel Acceleration: 2200.00
Setting Print and Travel Acceleration: 3000.00
Setting Print and Travel Acceleration: 2200.00
Setting Print and Travel Acceleration: 3000.00
Setting Print and Travel Acceleration: 2200.00
Setting Print and Travel Acceleration: 3000.00
Setting Print and Travel Acceleration: 2200.00
Setting Print and Travel Acceleration: 800.00
Setting Print and Travel Acceleration: 2200.00
Setting Print and Travel Acceleration: 3000.00
Setting Print and Travel Acceleration: 2200.00
Setting Print and Travel Acceleration: 3000.00
Setting Print and Travel Acceleration: 2200.00
Setting Print and Travel Acceleration: 3000.00
Setting Print and Travel Acceleration: 2200.00
Setting Print and Travel Acceleration: 800.00
Setting Print and Travel Acceleration: 2200.00
Done printing file
echo:enqueueing "M84 X Y Z E"
echo:enqueueing "M31"
>>> gcode_G28
current_position=(86.70, 102.99, 0.70) : setup_for_endstop_or_probe_move
> endstops.enable(true)
Raise Z (before homing) to 5.00
do_blocking_move_to(86.70, 102.99, 5.00)
>>> homeaxis(0)
current_position=(0.00, 102.99, 5.00) : sync_plan_position
echo:busy: processing
current_position=(0.00, 102.99, 5.00) : sync_plan_position
current_position=(0.00, 102.99, 5.00) : > TRIGGER ENDSTOP
>>> set_axis_is_at_home(0)
For 88 axis:
 home_offset = 0.00
 position_shift = 0.00
 sw_endstop_min = 0.00
 sw_endstop_max = 190.00
> home_offset[88] = 0.00
current_position=(0.00, 102.99, 5.00) : 
<<< set_axis_is_at_home(0)
current_position=(0.00, 102.99, 5.00) : sync_plan_position
current_position=(0.00, 102.99, 5.00) : > AFTER set_axis_is_at_home
<<< homeaxis(0)
current_position=(0.00, 102.99, 5.00) : > homeX
current_position=(0.00, 102.99, 5.00) : sync_plan_position
> endstops.not_homing()
current_position=(0.00, 102.99, 5.00) : clean_up_after_endstop_or_probe_move
<<< gcode_G28
X:0.00 Y:102.99 Z:5.00 E:0.00 Count X: 0 Y:7351 Z:2002
echo:Print time 0h 2m 43s