diff --git a/Marlin/Conditionals.h b/Marlin/Conditionals.h
index 1b4accd90a30..27ba3c86de41 100644
--- a/Marlin/Conditionals.h
+++ b/Marlin/Conditionals.h
@@ -197,6 +197,9 @@
   #endif
 
   #if ENABLED(ULTIPANEL)
+    #if DISABLED(DISABLE_SDSUPPORT)
+      #define SDSUPPORT
+    #endif
     #define NEWPANEL  //enable this if you have a click-encoder panel
     #define ULTRA_LCD
     #ifndef LCD_WIDTH
diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h
index d0a49aade3c4..b2080201cbbb 100644
--- a/Marlin/Configuration.h
+++ b/Marlin/Configuration.h
@@ -761,8 +761,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 
 //#define ULTRA_LCD  //general LCD support, also 16x2
 //#define DOGLCD  // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family)
-//#define SDSUPPORT // Enable SD Card Support in Hardware Console
-                    // Changed behaviour! If you need SDSUPPORT uncomment it!
+//#define DISABLE_SDSUPPORT // Disable SD Card Support for controllers that have it
 //#define SPI_SPEED SPI_HALF_SPEED // (also SPI_QUARTER_SPEED, SPI_EIGHTH_SPEED) Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error)
 //#define SD_CHECK_AND_RETRY // Use CRC checks and retries on the SD communication
 //#define ENCODER_PULSES_PER_STEP 1 // Increase if you have a high resolution encoder
diff --git a/Marlin/example_configurations/Felix/Configuration.h b/Marlin/example_configurations/Felix/Configuration.h
index 2da7f04f6d83..1f9b5d0eadba 100644
--- a/Marlin/example_configurations/Felix/Configuration.h
+++ b/Marlin/example_configurations/Felix/Configuration.h
@@ -744,8 +744,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 
 //#define ULTRA_LCD  //general LCD support, also 16x2
 //#define DOGLCD  // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family)
-//#define SDSUPPORT // Enable SD Card Support in Hardware Console
-                    // Changed behaviour! If you need SDSUPPORT uncomment it!
+//#define DISABLE_SDSUPPORT // Disable SD Card Support for controllers that have it
 //#define SPI_SPEED SPI_HALF_SPEED // (also SPI_QUARTER_SPEED, SPI_EIGHTH_SPEED) Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error)
 //#define SD_CHECK_AND_RETRY // Use CRC checks and retries on the SD communication
 //#define ENCODER_PULSES_PER_STEP 1 // Increase if you have a high resolution encoder
diff --git a/Marlin/example_configurations/Felix/Configuration_DUAL.h b/Marlin/example_configurations/Felix/Configuration_DUAL.h
index 60697ed0e8cd..07d0a065d22c 100644
--- a/Marlin/example_configurations/Felix/Configuration_DUAL.h
+++ b/Marlin/example_configurations/Felix/Configuration_DUAL.h
@@ -741,8 +741,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 
 //#define ULTRA_LCD  //general LCD support, also 16x2
 //#define DOGLCD  // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family)
-//#define SDSUPPORT // Enable SD Card Support in Hardware Console
-                    // Changed behaviour! If you need SDSUPPORT uncomment it!
+//#define DISABLE_SDSUPPORT // Disable SD Card Support for controllers that have it
 //#define SPI_SPEED SPI_HALF_SPEED // (also SPI_QUARTER_SPEED, SPI_EIGHTH_SPEED) Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error)
 //#define SD_CHECK_AND_RETRY // Use CRC checks and retries on the SD communication
 //#define ENCODER_PULSES_PER_STEP 1 // Increase if you have a high resolution encoder
diff --git a/Marlin/example_configurations/Hephestos/Configuration.h b/Marlin/example_configurations/Hephestos/Configuration.h
index 9e0af0a32903..c5f1b386a566 100644
--- a/Marlin/example_configurations/Hephestos/Configuration.h
+++ b/Marlin/example_configurations/Hephestos/Configuration.h
@@ -753,8 +753,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
 
 #define ULTRA_LCD  //general LCD support, also 16x2
 //#define DOGLCD  // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family)
-#define SDSUPPORT // Enable SD Card Support in Hardware Console
-                  // Changed behaviour! If you need SDSUPPORT uncomment it!
+//#define DISABLE_SDSUPPORT // Disable SD Card Support for controllers that have it
 //#define SPI_SPEED SPI_HALF_SPEED // (also SPI_QUARTER_SPEED, SPI_EIGHTH_SPEED) Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error)
 //#define SD_CHECK_AND_RETRY // Use CRC checks and retries on the SD communication
 //#define ENCODER_PULSES_PER_STEP 1 // Increase if you have a high resolution encoder
diff --git a/Marlin/example_configurations/Hephestos_2/Configuration.h b/Marlin/example_configurations/Hephestos_2/Configuration.h
index a1a89e37150c..98f7f7367e9d 100644
--- a/Marlin/example_configurations/Hephestos_2/Configuration.h
+++ b/Marlin/example_configurations/Hephestos_2/Configuration.h
@@ -755,8 +755,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 
 //#define ULTRA_LCD  //general LCD support, also 16x2
 //#define DOGLCD  // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family)
-#define SDSUPPORT // Enable SD Card Support in Hardware Console
-                  // Changed behaviour! If you need SDSUPPORT uncomment it!
+//#define DISABLE_SDSUPPORT // Disable SD Card Support for controllers that have it
 //#define SPI_SPEED SPI_HALF_SPEED // (also SPI_QUARTER_SPEED, SPI_EIGHTH_SPEED) Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error)
 //#define SD_CHECK_AND_RETRY // Use CRC checks and retries on the SD communication
 //#define ENCODER_PULSES_PER_STEP 1 // Increase if you have a high resolution encoder
diff --git a/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h b/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h
index 553c07afa5a5..68781eb4e036 100644
--- a/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h
+++ b/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h
@@ -761,8 +761,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 
 #define ULTRA_LCD  //general LCD support, also 16x2
 //#define DOGLCD  // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family)
-#define SDSUPPORT // Enable SD Card Support in Hardware Console
-                  // Changed behaviour! If you need SDSUPPORT uncomment it!
+//#define DISABLE_SDSUPPORT // Disable SD Card Support for controllers that have it
 //#define SPI_SPEED SPI_HALF_SPEED // (also SPI_QUARTER_SPEED, SPI_EIGHTH_SPEED) Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error)
 #define SD_CHECK_AND_RETRY // Use CRC checks and retries on the SD communication
 //#define ENCODER_PULSES_PER_STEP 1 // Increase if you have a high resolution encoder
diff --git a/Marlin/example_configurations/RigidBot/Configuration.h b/Marlin/example_configurations/RigidBot/Configuration.h
index 733b377cd43e..640839679e26 100644
--- a/Marlin/example_configurations/RigidBot/Configuration.h
+++ b/Marlin/example_configurations/RigidBot/Configuration.h
@@ -756,8 +756,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 
 //#define ULTRA_LCD  //general LCD support, also 16x2
 //#define DOGLCD  // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family)
-#define SDSUPPORT // Enable SD Card Support in Hardware Console
-                  // Changed behaviour! If you need SDSUPPORT uncomment it!
+//#define DISABLE_SDSUPPORT // Disable SD Card Support for controllers that have it
 #define SPI_SPEED SPI_EIGHTH_SPEED // Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error)
 //#define SD_CHECK_AND_RETRY // Use CRC checks and retries on the SD communication
 //#define ENCODER_PULSES_PER_STEP 1 // Increase if you have a high resolution encoder
diff --git a/Marlin/example_configurations/SCARA/Configuration.h b/Marlin/example_configurations/SCARA/Configuration.h
index 40e20cfd780b..28b464dec756 100644
--- a/Marlin/example_configurations/SCARA/Configuration.h
+++ b/Marlin/example_configurations/SCARA/Configuration.h
@@ -769,8 +769,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 
 //#define ULTRA_LCD  //general LCD support, also 16x2
 //#define DOGLCD  // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family)
-//#define SDSUPPORT // Enable SD Card Support in Hardware Console
-                    // Changed behaviour! If you need SDSUPPORT uncomment it!
+//#define DISABLE_SDSUPPORT // Disable SD Card Support for controllers that have it
 //#define SPI_SPEED SPI_HALF_SPEED // (also SPI_QUARTER_SPEED, SPI_EIGHTH_SPEED) Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error)
 //#define SD_CHECK_AND_RETRY // Use CRC checks and retries on the SD communication
 //#define ENCODER_PULSES_PER_STEP 1 // Increase if you have a high resolution encoder
diff --git a/Marlin/example_configurations/TAZ4/Configuration.h b/Marlin/example_configurations/TAZ4/Configuration.h
index 38e7e20cf2c8..0ceb2d477146 100644
--- a/Marlin/example_configurations/TAZ4/Configuration.h
+++ b/Marlin/example_configurations/TAZ4/Configuration.h
@@ -782,8 +782,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 
 //#define ULTRA_LCD  //general LCD support, also 16x2
 //#define DOGLCD  // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family)
-//#define SDSUPPORT // Enable SD Card Support in Hardware Console
-                    // Changed behaviour! If you need SDSUPPORT uncomment it!
+//#define DISABLE_SDSUPPORT // Disable SD Card Support for controllers that have it
 //#define SPI_SPEED SPI_HALF_SPEED // (also SPI_QUARTER_SPEED, SPI_EIGHTH_SPEED) Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error)
 //#define SD_CHECK_AND_RETRY // Use CRC checks and retries on the SD communication
 #define ENCODER_PULSES_PER_STEP 2 // Increase if you have a high resolution encoder
diff --git a/Marlin/example_configurations/WITBOX/Configuration.h b/Marlin/example_configurations/WITBOX/Configuration.h
index fd3fa38d0972..37af5743ce4b 100644
--- a/Marlin/example_configurations/WITBOX/Configuration.h
+++ b/Marlin/example_configurations/WITBOX/Configuration.h
@@ -753,8 +753,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
 
 #define ULTRA_LCD  //general LCD support, also 16x2
 //#define DOGLCD  // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family)
-#define SDSUPPORT // Enable SD Card Support in Hardware Console
-                  // Changed behaviour! If you need SDSUPPORT uncomment it!
+//#define DISABLE_SDSUPPORT // Disable SD Card Support for controllers that have it
 //#define SPI_SPEED SPI_HALF_SPEED // (also SPI_QUARTER_SPEED, SPI_EIGHTH_SPEED) Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error)
 //#define SD_CHECK_AND_RETRY // Use CRC checks and retries on the SD communication
 //#define ENCODER_PULSES_PER_STEP 1 // Increase if you have a high resolution encoder
diff --git a/Marlin/example_configurations/adafruit/ST7565/Configuration.h b/Marlin/example_configurations/adafruit/ST7565/Configuration.h
index 052008aa58ba..a9576dd1fd03 100644
--- a/Marlin/example_configurations/adafruit/ST7565/Configuration.h
+++ b/Marlin/example_configurations/adafruit/ST7565/Configuration.h
@@ -761,8 +761,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 
 //#define ULTRA_LCD  //general LCD support, also 16x2
 //#define DOGLCD  // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family)
-#define SDSUPPORT // Enable SD Card Support in Hardware Console
-                  // Changed behaviour! If you need SDSUPPORT uncomment it!
+//#define DISABLE_SDSUPPORT // Disable SD Card Support for controllers that have it
 #define SPI_SPEED SPI_HALF_SPEED // (also SPI_QUARTER_SPEED, SPI_EIGHTH_SPEED) Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error)
 //#define SD_CHECK_AND_RETRY // Use CRC checks and retries on the SD communication
 //#define ENCODER_PULSES_PER_STEP 1 // Increase if you have a high resolution encoder
diff --git a/Marlin/example_configurations/delta/biv2.5/Configuration.h b/Marlin/example_configurations/delta/biv2.5/Configuration.h
index ce1bbf5cc3bd..d5eb2ad3bc3c 100644
--- a/Marlin/example_configurations/delta/biv2.5/Configuration.h
+++ b/Marlin/example_configurations/delta/biv2.5/Configuration.h
@@ -883,8 +883,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
 
 //#define ULTRA_LCD  //general LCD support, also 16x2
 //#define DOGLCD  // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family)
-//#define SDSUPPORT // Enable SD Card Support in Hardware Console
-                    // Changed behaviour! If you need SDSUPPORT uncomment it!
+//#define DISABLE_SDSUPPORT // Disable SD Card Support for controllers that have it
 //#define SPI_SPEED SPI_HALF_SPEED // (also SPI_QUARTER_SPEED, SPI_EIGHTH_SPEED) Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error)
 //#define SD_CHECK_AND_RETRY // Use CRC checks and retries on the SD communication
 //#define ENCODER_PULSES_PER_STEP 1 // Increase if you have a high resolution encoder
diff --git a/Marlin/example_configurations/delta/generic/Configuration.h b/Marlin/example_configurations/delta/generic/Configuration.h
index bc323fd5a56c..7b0efa039ade 100644
--- a/Marlin/example_configurations/delta/generic/Configuration.h
+++ b/Marlin/example_configurations/delta/generic/Configuration.h
@@ -883,8 +883,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
 
 //#define ULTRA_LCD  //general LCD support, also 16x2
 //#define DOGLCD  // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family)
-//#define SDSUPPORT // Enable SD Card Support in Hardware Console
-                    // Changed behaviour! If you need SDSUPPORT uncomment it!
+//#define DISABLE_SDSUPPORT // Disable SD Card Support for controllers that have it
 //#define SPI_SPEED SPI_HALF_SPEED // (also SPI_QUARTER_SPEED, SPI_EIGHTH_SPEED) Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error)
 //#define SD_CHECK_AND_RETRY // Use CRC checks and retries on the SD communication
 //#define ENCODER_PULSES_PER_STEP 1 // Increase if you have a high resolution encoder
diff --git a/Marlin/example_configurations/delta/kossel_mini/Configuration.h b/Marlin/example_configurations/delta/kossel_mini/Configuration.h
index fbaa538e9665..8bda85600706 100644
--- a/Marlin/example_configurations/delta/kossel_mini/Configuration.h
+++ b/Marlin/example_configurations/delta/kossel_mini/Configuration.h
@@ -887,8 +887,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 
 //#define ULTRA_LCD  //general LCD support, also 16x2
 //#define DOGLCD  // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family)
-//#define SDSUPPORT // Enable SD Card Support in Hardware Console
-                    // Changed behaviour! If you need SDSUPPORT uncomment it!
+//#define DISABLE_SDSUPPORT // Disable SD Card Support for controllers that have it
 //#define SPI_SPEED SPI_HALF_SPEED // (also SPI_QUARTER_SPEED, SPI_EIGHTH_SPEED) Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error)
 //#define SD_CHECK_AND_RETRY // Use CRC checks and retries on the SD communication
 //#define ENCODER_PULSES_PER_STEP 1 // Increase if you have a high resolution encoder
diff --git a/Marlin/example_configurations/delta/kossel_pro/Configuration.h b/Marlin/example_configurations/delta/kossel_pro/Configuration.h
index aedcf72af2e3..6865b39355c7 100644
--- a/Marlin/example_configurations/delta/kossel_pro/Configuration.h
+++ b/Marlin/example_configurations/delta/kossel_pro/Configuration.h
@@ -880,8 +880,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 
 //#define ULTRA_LCD  //general LCD support, also 16x2
 //#define DOGLCD  // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family)
-#define SDSUPPORT // Enable SD Card Support in Hardware Console
-                  // Changed behaviour! If you need SDSUPPORT uncomment it!
+//#define DISABLE_SDSUPPORT // Disable SD Card Support for controllers that have it
 //#define SPI_SPEED SPI_HALF_SPEED // (also SPI_QUARTER_SPEED, SPI_EIGHTH_SPEED) Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error)
 //#define SD_CHECK_AND_RETRY // Use CRC checks and retries on the SD communication
 //#define ENCODER_PULSES_PER_STEP 1 // Increase if you have a high resolution encoder
diff --git a/Marlin/example_configurations/delta/kossel_xl/Configuration.h b/Marlin/example_configurations/delta/kossel_xl/Configuration.h
index cba52bf4afda..b3be3e4afa99 100644
--- a/Marlin/example_configurations/delta/kossel_xl/Configuration.h
+++ b/Marlin/example_configurations/delta/kossel_xl/Configuration.h
@@ -797,8 +797,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 
 //#define ULTRA_LCD  //general LCD support, also 16x2
 //#define DOGLCD  // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family)
-//#define SDSUPPORT // Enable SD Card Support in Hardware Console
-                    // Changed behaviour! If you need SDSUPPORT uncomment it!
+//#define DISABLE_SDSUPPORT // Disable SD Card Support for controllers that have it
 //#define SPI_SPEED SPI_HALF_SPEED // (also SPI_QUARTER_SPEED, SPI_EIGHTH_SPEED) Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error)
 //#define SD_CHECK_AND_RETRY // Use CRC checks and retries on the SD communication
 //#define ENCODER_PULSES_PER_STEP 1 // Increase if you have a high resolution encoder
diff --git a/Marlin/example_configurations/makibox/Configuration.h b/Marlin/example_configurations/makibox/Configuration.h
index 301c7d9b6fe9..4cad962e8373 100644
--- a/Marlin/example_configurations/makibox/Configuration.h
+++ b/Marlin/example_configurations/makibox/Configuration.h
@@ -764,8 +764,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 
 //#define ULTRA_LCD  //general LCD support, also 16x2
 //#define DOGLCD  // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family)
-#define SDSUPPORT // Enable SD Card Support in Hardware Console
-                  // Changed behaviour! If you need SDSUPPORT uncomment it!
+//#define DISABLE_SDSUPPORT // Disable SD Card Support for controllers that have it
 #define SPI_SPEED SPI_HALF_SPEED // (also SPI_QUARTER_SPEED, SPI_EIGHTH_SPEED) Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error)
 //#define SD_CHECK_AND_RETRY // Use CRC checks and retries on the SD communication
 //#define ENCODER_PULSES_PER_STEP 1 // Increase if you have a high resolution encoder
diff --git a/Marlin/example_configurations/tvrrug/Round2/Configuration.h b/Marlin/example_configurations/tvrrug/Round2/Configuration.h
index f162ff7b600b..ada36700342d 100644
--- a/Marlin/example_configurations/tvrrug/Round2/Configuration.h
+++ b/Marlin/example_configurations/tvrrug/Round2/Configuration.h
@@ -755,8 +755,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
 
 //#define ULTRA_LCD  //general LCD support, also 16x2
 //#define DOGLCD  // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family)
-//#define SDSUPPORT // Enable SD Card Support in Hardware Console
-                    // Changed behaviour! If you need SDSUPPORT uncomment it!
+//#define DISABLE_SDSUPPORT // Disable SD Card Support for controllers that have it
 //#define SPI_SPEED SPI_HALF_SPEED // (also SPI_QUARTER_SPEED, SPI_EIGHTH_SPEED) Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error)
 //#define SD_CHECK_AND_RETRY // Use CRC checks and retries on the SD communication
 //#define ENCODER_PULSES_PER_STEP 1 // Increase if you have a high resolution encoder