radvd.conf.5.man

.\"
.\"
.\"   Authors:
.\"    Lars Fenneberg		<lf@elemental.net>
.\"    Marko Myllynen           <myllynen@lut.fi>	 
.\"
.\"   This software is Copyright 1996-2000 by the above mentioned author(s), 
.\"   All Rights Reserved.
.\"
.\"   The license which is distributed with this software in the file COPYRIGHT
.\"   applies to this software. If your distribution is missing this file, you
.\"   may request it from <reubenhwk@gmail.com>.
.\"
.\"
.\"
.TH RADVD.CONF 5 "4 Jan 2011" "radvd @VERSION@" ""
.SH NAME
radvd.conf \- configuration file of the router advertisement daemon
.B radvd
.SH DESCRIPTION
This file describes the information which is included in the router
advertisement (RA) of a specific interface.
.P
The file contains one or more interface definitions of the form:

.nf
.BR "interface " "name " {
	list of interface specific options
	list of prefix definitions
	list of clients (IPv6 addresses) to advertise to
	list of route definitions
	list of RDNSS definitions
	list of DNSSL definitions
	list of ABRO definitions
	list of NAT64 pref64 definitions
	list of acceptable RA source addresses
.B };
.fi

All the possible interface specific options are detailed below.  Each
option has to be terminated by a semicolon. Options are not case sensitive.

Prefix definitions are of the form:

.nf
.BR "prefix " prefix / "length " {
	list of prefix specific options
.B };
.fi

Prefix can be network prefix or the address of the interface.
The address of interface should be used when using Mobile IPv6
extensions.

Special prefix "::/64" is also supported on systems that implement getifaddrs()
(on other systems, configuration activation fails and radvd exits).
When configured, radvd
picks all non-link-local prefix assigned to the interface and starts advertising
it.  This may be applicable in non-6to4 scenarios where the upstream prefix might
change.  This option is incompatible with Base6to4Interface option.
AdvRouterAddr option is always enabled when this configuration is used.

All the possible prefix specific options are described below.  Each
option has to be terminated by a semicolon.

Decimal values are allowed only for MinDelayBetweenRAs,
MaxRtrAdvInterval and MinRtrAdvInterval.  Decimal values should
be used only when using Mobile IPv6 extensions.

Route definitions are of the form:

.nf
.BR "route " prefix / "length " {
	list of route specific options
.B };
.fi

The prefix of a route definition should be network prefix; it can be used to
advertise more specific routes to the hosts.

RDNSS (Recursive DNS server) definitions are of the form:

.nf
.BR "RDNSS " "ip [ip] [ip] " {
	list of rdnss specific options
.B };
.fi

DNSSL (DNS Search List) definitions are of the form:

.nf
.BR "DNSSL " "suffix [suffix] [suffix] [...] " {
	list of dnssl specific options
.B };
.fi

By default radvd will send multicast route advertisements so that every node on the link can use them.
The list of clients (IPv6 address) to advertise to, and accept route solicitations from can be configured.
If done, radvd does not send messages to the multicast addresses but
to the configured unicast addresses only.  Solicitations from other addresses are refused unless
UnrestrictedUnicast is enabled.
This is similar to UnicastOnly but includes periodic messages and incoming client access
configuration.  See examples section for a use case of this.

The definitions are of the form:

.nf
.BR clients " " {
        list of IPv6 addresses
.B };
.fi

Clients can be prefixed with "!" to ignore them completely and never send advertisements to them.

By default radvd will use the first link-local address for the interface as the
source address for route advertisements. This can be overwritten by manually
setting the list of acceptable source addresses. If done, radvd will use the
first address from the interface that is present in the configured source
addresses only. This functionality will NOT spoof the source address, but may be useful in combination with VRRP or other functionality that 

.nf
.BR AdvRASrcAddress " " {
        list of IPv6 addresses
.B };
.fi

ABRO (Authoritative Border Router Option) definitions are of the form:

.nf
.BR "abro " "IPv6-address " {
        list of abro specific options
.B };
.fi

NAT64 pref64 (the NAT64 prefix included in the router advertisements):

.nf
.BR "nat64prefix " prefix / "length " {
	list of NAT64 prefix specific options
.B };
.fi

The value of
.B length
can only be one of /32, /40, /48, /56, /64, or /96.

.SH INTERFACE SPECIFIC OPTIONS

.TP
.BR IgnoreIfMissing " " on | off

A flag indicating whether or not the interface is ignored
if it does not exist at start-up. 

This is useful for dynamic interfaces which are not active when radvd
starts or which are dynamically disabled and re-enabled during the time
radvd runs.

Current versions of radvd automatically try to re-enable interfaces.

Enabling IgnoreIfMissing also quenches certain warnings in log messages
relating to missing interfaces.

Default: on

.TP
.BR AdvSendAdvert " " on | off

A flag indicating whether or not the router sends
periodic router advertisements and responds to
router solicitations. 

This option no longer has to be specified first, but it
needs to be
.B on
to enable advertisement on this interface.

Default: off

.TP
.BR UnicastOnly " " on | off

Indicates that the interface link type only supports unicast.
This will prevent unsolicited advertisements from being sent, and
will cause solicited advertisements to be unicast to the
soliciting node.  This option is necessary for non-broadcast,
multiple-access links, such as ISATAP.

Default: off

.TP
.BR UnrestrictedUnicast " " on | off

A flag indicating whether or not to respond to router
solicitations when there is a list of clients configured.

This allows regular unsolicited advertisements to be sent
to some clients without ignoring router solicitations from
unknown clients.

Default: off

.TP
.BR AdvRASolicitedUnicast " " on | off

Indicates that router solicitations will be responded to with unicast
router advertisements, as recommended by RFC7772. Large networks with a
high concentration of mobile devices might experience like battery
depletion, when solicited Router Advertisement messages are multicast.

This corresponds to the Cisco IOS option
.B ipv6 nd ra solicited unicast

Default: on

.TP
.BR "MaxRtrAdvInterval " seconds

The maximum time allowed between sending unsolicited multicast
router advertisements from the interface, in seconds.

Must be no less than 4 seconds and no greater than 1800 seconds.

Minimum when using Mobile IPv6 extensions: 0.07.

For values less than 0.2 seconds, 0.02 seconds is added to account for
scheduling granularities as specified in RFC3775.

Default: 600 seconds	

.TP
.BR "MinRtrAdvInterval " seconds

The minimum time allowed between sending unsolicited multicast
router advertisements from the interface, in seconds.

Must be no less than 3 seconds and no greater than 0.75 *
MaxRtrAdvInterval.

Minimum when using Mobile IPv6 extensions: 0.03.

Default: 0.33 * MaxRtrAdvInterval

.TP
.BR "MinDelayBetweenRAs " seconds

The minimum time allowed between sending multicast
router advertisements from the interface, in seconds.

This applies to solicited multicast RAs.
This is defined as the protocol constant MIN_DELAY_BETWEEN_RAS in RFC4861.
MIPv6 redefines this parameter to have a minimum of 0.03 seconds.

Minimum when using Mobile IPv6 extensions: 0.03.

Default: 3 

.TP
.BR AdvManagedFlag " " on | off

When set, hosts use the administered (stateful) protocol for address
autoconfiguration in addition to any addresses autoconfigured using
stateless address autoconfiguration.  The use of this flag is
described in RFC 4862.

Default: off

.TP
.BR AdvOtherConfigFlag " " on | off

When set, hosts use the administered (stateful) protocol for
autoconfiguration of other (non-address) information.  The use of
this flag is described in RFC 4862.

Default: off

.TP
.BR "AdvLinkMTU " integer

The MTU option is used in  router advertisement messages to ensure
that all nodes on a link use the same MTU value in those cases where
the link MTU is not well known.

If specified, i.e. not 0, must not be smaller than 1280 and not greater
than the maximum MTU allowed for this link (e.g. ethernet has
a maximum MTU of 1500. See RFC 4864).

Default: 0

.TP
.BR "AdvReachableTime " milliseconds

The time, in milliseconds, that a node assumes a neighbor is
reachable after having received a reachability confirmation.  Used
by the Neighbor Unreachability Detection algorithm (see Section
7.3 of RFC 4861).  A value of zero means unspecified (by this router).

Must be no greater than 3,600,000 milliseconds (1 hour).

Default: 0

.TP
.BR "AdvRetransTimer " milliseconds

The time, in milliseconds, between retransmitted Neighbor
Solicitation messages.  Used by address resolution and the Neighbor
Unreachability Detection algorithm (see Sections 7.2 and 7.3 of RFC 4861).
A value of zero means unspecified (by this router).

Default: 0

.TP
.BR "AdvCurHopLimit " integer

The default value that should be placed in the Hop Count field of
the IP header for outgoing (unicast) IP packets.  The value should
be set to the current diameter of the Internet.  The value zero
means unspecified (by this router).

Default: 64

.TP
.BR "AdvDefaultLifetime " seconds

The lifetime associated with the default router in units of seconds. 
The maximum value corresponds to 18.2 hours.  A lifetime of 0
indicates that the router is not a default router and should not
appear on the default router list.  The router lifetime applies only
to the router's usefulness as a default router; it does not apply to
information contained in other message fields or options.  Options
that need time limits for their information include their own
lifetime fields.

Must be either zero or between MaxRtrAdvInterval and 9000 seconds.

Default: 3 * MaxRtrAdvInterval (Minimum 1 second).

.TP
.BR AdvDefaultPreference " " low | medium | high

The preference associated with the default router, as either "low",
"medium", or "high".

Default: medium

.TP
.BR AdvSourceLLAddress " " on | off

When set, the link-layer address of the outgoing interface is
included in the RA.

Default: on

.TP
.BR RemoveAdvOnExit " " on | off

Upon shutdown, send a final advertisement with zero Router Lifetime. This should cause the router and routes to be immediately removed from the receiving end-nodes' route table. This may need to be disabled ("off") in an vrrp or carp setup.

Default: on

.TP
.BR AdvHomeAgentFlag " " on | off

When set, indicates that sending router is able to serve as Mobile
IPv6 Home Agent.  When set, minimum limits specified by Mobile IPv6
are used for MinRtrAdvInterval and MaxRtrAdvInterval.

Default: off

.TP
.BR AdvHomeAgentInfo " " on | off

When set, Home Agent Information Option (specified by Mobile IPv6)
is included in Router Advertisements.  AdvHomeAgentFlag must also
be set when using this option.

Default: off

.TP
.BR "HomeAgentLifetime " seconds

The length of time in seconds (relative to the time the packet is
sent) that the router is offering Mobile IPv6 Home Agent services.  
A value 0 must not be used.  The maximum lifetime is 65520 seconds 
(18.2 hours).  This option is ignored, if AdvHomeAgentInfo is not
set.

If both HomeAgentLifetime and HomeAgentPreference are set to their
default values, Home Agent Information Option will not be sent.

Default: AdvDefaultLifetime

.TP
.BR "HomeAgentPreference " integer

The preference for the Home Agent sending this Router Advertisement.  
Values greater than 0 indicate more preferable Home Agent, values
less than 0 indicate less preferable Home Agent.  This option is
ignored, if AdvHomeAgentInfo is not set.

If both HomeAgentLifetime and HomeAgentPreference are set to their
default values, Home Agent Information Option will not be sent.

Default: 0

.TP
.BR AdvMobRtrSupportFlag " " on | off

When set, the Home Agent signals it supports Mobile Router
registrations (specified by NEMO Basic).  AdvHomeAgentInfo must also
be set when using this option.

Default: off

.TP
.BR AdvIntervalOpt " " on | off

When set, Advertisement Interval Option (specified by Mobile IPv6)
is included in Router Advertisements.  When set, minimum limits
specified by Mobile IPv6 are used for MinRtrAdvInterval and
MaxRtrAdvInterval.

The advertisement interval is based on the configured MaxRtrAdvInterval
parameter except where this is less than 200ms.  In this case,
the advertised interval is ( MaxRtrAdvInterval + 20ms ).

Default: off

.TP
.BR AdvCaptivePortalAPI " " \[dq] URL \[dq]

When set, advertise RFC8908 Captive-Portal API URL.

See RFC8952 Captive Portal Architecture, RFC8910 Captive-Portal
Identification in DHCP and Router Advertisements (RAs) and
RFC8908 Captive Portal API for more information.

Most likely you do not need this.

Default: not included

.SH PREFIX SPECIFIC OPTIONS

.TP
.BR AdvOnLink " " on | off

When set, indicates that this prefix can be used for on-link
determination.  When not set the advertisement makes no statement
about on-link or off-link properties of the prefix.  For instance,
the prefix might be used for address configuration with some of the
addresses belonging to the prefix being on-link and others being
off-link.

Default: on

.TP
.BR AdvAutonomous " " on | off

When set, indicates that this prefix can be used for autonomous
address configuration as specified in RFC 4862.

Default: on

.TP
.BR AdvRouterAddr " " on | off

When set, indicates that the address of interface is sent instead of
network prefix, as is required by Mobile IPv6.  When set, minimum
limits specified by Mobile IPv6 are used for MinRtrAdvInterval and
MaxRtrAdvInterval.

Default: off

.TP
.BR "AdvValidLifetime " seconds "" | infinity

The length of time in seconds (relative to the time the packet is
sent) that the prefix is valid for the purpose of on-link
determination.  The symbolic value
.B infinity
represents infinity (i.e. a value of all one bits (0xffffffff)).
The valid lifetime is also used by RFC 4862.

Note that clients will ignore AdvValidLifetime of an existing prefix
if the lifetime is below two hours, as required in RFC 4862 Section 5.5.3
point e).

Note: RFC4861's suggested default value is significantly longer: 30 days.

Default: 86400 seconds (1 day)

.TP
.BR "AdvPreferredLifetime " seconds "" | infinity

The length of time in seconds (relative to the time the packet is
sent) that addresses generated from the prefix via stateless address
autoconfiguration remain preferred. 
The symbolic value
.B infinity
represents infinity (i.e. a value of all one bits (0xffffffff)).
See RFC 4862.

Note: RFC4861's suggested default value is significantly longer: 7 days.

Default: 14400 seconds (4 hours)

.TP
.BR DeprecatePrefix " " on | off

Upon shutdown, this option will cause radvd to deprecate the prefix by announcing it in the radvd shutdown RA with a zero preferred lifetime and a valid lifetime slightly greater than 2 hours. This will encourage end-nodes using this prefix to deprecate any associated addresses immediately. Note that this option should only be used when only one router is announcing the prefix onto the link, otherwise end-nodes will deprecate associated addresses despite the prefix still being valid for preferred use.

See RFC4862, section 5.5.3., "Router Advertisement Processing", part (e).

Default: off

.TP
.BR DecrementLifetimes " " on | off

This option causes radvd to decrement the values of the preferred and valid lifetimes for the prefix over time. The lifetimes are decremented by the number of seconds since the last RA. If radvd receives a SIGUSR1 signal, it will reset the values of the preferred and valid lifetimes back to the initial values used by radvd when it started. If radvd never receives a SIGUSR1 signal, it will continue to decrement the lifetimes until the preferred lifetime reaches zero. After a final RA with a zero value preferred lifetime, radvd will cease to announce the prefix. If a SIGUSR1 signal then causes the lifetimes to be reset, the prefix will then re-appear in the RAs.

This option is intended to be used in conjunction with a DHCPv6 client that is using the Identity Association for Prefix Delegation (IA_PD) option to acquire a prefix from a Delegating Router for use by a Requesting Router. In this scenario, the prefix(es) from within the delegated prefix that are announced by radvd would age in parallel with and at the same rate as the delegated prefix, and expire at approximately the same time, if the delegated prefix's life isn't extended.

See RFC3633, "IPv6 Prefix Options for Dynamic Host Configuration Protocol (DHCP) version 6".

Default: off

.TP
.BR "Base6Interface " name 

If this options is specified, this prefix will be combined with the
IPv6 address of the interface specified by
.B name.  
The resulting prefix length will be 64.

.TP
.BR "Base6to4Interface " name 

If this option is specified, this prefix will be combined with the
IPv4 address of interface
.B name
to produce a valid 6to4 prefix. The first 16 bits of this prefix
will be replaced by
.B 2002
and the next 32 bits of this prefix will be replaced by the IPv4
address assigned to interface
.B name
at configuration time. The remaining 80 bits of the prefix (including
the SLA ID) will be advertised as specified in the configuration file.
See the next section for an example.

If interface
.B name
is not available at configuration time, a warning will be written to
the log and this prefix will be disabled until radvd is reconfigured.

This option enables systems with dynamic IPv4 addresses to update their
advertised 6to4 prefixes simply by restarting radvd or sending a SIGHUP
signal to cause radvd to reconfigure itself.

Note that 6to4 prefixes derived from dynamically-assigned IPv4 addresses
should be advertised with a significantly shorter lifetime (see the
.B AdvValidLifetime
and
.B AdvPreferredLifetime
options).

For more information on 6to4, see RFC 3056.

Default: 6to4 is not used

.SH ROUTE SPECIFIC OPTIONS

.TP
.BR "AdvRouteLifetime " seconds "" | infinity

The lifetime associated with the route in units of seconds.
The symbolic value
.B infinity
represents infinity (i.e. a value of all one bits (0xffffffff)).

Default: 3 * MaxRtrAdvInterval

.TP
.BR AdvRoutePreference " " low | medium | high

The preference associated with the default router, as either "low",
"medium", or "high".

Default: medium

.TP
.BR RemoveRoute " " on | off 

Upon shutdown, announce this route with a zero second lifetime. This should cause the route to be immediately removed from the receiving end-nodes' route table.

Default: on

.SH RDNSS SPECIFIC OPTIONS

.TP
.BR "AdvRDNSSLifetime " seconds | infinity
The maximum duration how long the RDNSS entries are used for name resolution.
A value of 0 means the nameserver must no longer be used.
As described in RFC8106, the use of default value or a larger value ensures the reliability of an entry even under the loss of RAs on links with a relatively high rate of packet loss.

Default: 3*MaxRtrAdvInterval

.TP
.BR FlushRDNSS " " on | off

Upon shutdown, announce the RDNSS entries with a zero second lifetime. This should cause the RDNSS addresses to be immediately removed from the end-nodes' list of Recursive DNS Servers.

Default: on

.SH DNSSL SPECIFIC OPTIONS

.TP
.BR "AdvDNSSLLifetime " seconds | infinity;
The maximum duration how long the DNSSL entries are used for name resolution.
A value of 0 means the suffix should no longer be used.
As described in RFC8106, the use of default value or a larger value ensures the reliability of an entry even under the loss of RAs on links with a relatively high rate of packet loss.

Default: 3*MaxRtrAdvInterval

.TP
.BR FlushDNSSL " " on | off

Upon shutdown, announce the DNSSL entries with a zero second lifetime. This should cause the DNSSL entries to be immediately removed from the end-nodes' DNS search list.

Default: on

.SH ABRO SPECIFIC OPTIONS

.TP
.BR "AdvValidLifetime " seconds
The time in units of that the set of border router information is valid.
A value of all zero bits assumes a default value of 10,000(~one week).

.TP
.BR "AdvVersionLow, AdvVersionHigh " unsigned integer
Both forms 32-bit unsigned version number corresponding to the set of information contained in RA message.

.SH NAT64 PREF64 SPECIFIC OPTIONS

.TP
.BR "AdvValidLifetime " seconds ""

The length of time in seconds (relative to the time the packet is
sent) that the prefix is valid for the purpose of NAT64 existence
determination. In case the value is not a multiple of 8, the validity
is rounded up to the next multiple of 8. The maximum is 65528 seconds.

Default: the lesser value of 3 * MaxRtrAdvInterval, or 65528

.SH EXAMPLES

.nf
interface eth0
{
        AdvSendAdvert on;
        prefix 2001:db8:0:1::/64
        {
                AdvOnLink on;
                AdvAutonomous on;
        };
};
.fi

It says that router advertisement daemon should advertise
(AdvSendAdvert on;) the prefix 2001:db8:0:1:: which has a length of 64
on the interface eth0.  Also the prefix should be marked as autonomous
(AdvAutonomous on;) and as on-link (AdvOnLink on;).  All the other
options are left on their default values.

To support movement detection of Mobile IPv6 Mobile Nodes, the
address of interface should be used instead of network prefix:

.nf
interface eth0
{
        AdvSendAdvert on;
        prefix 2001:db8:0:1::4/64
        {
                AdvOnLink on;
                AdvAutonomous on;
                AdvRouterAddr on;
        };
};
.fi

For 6to4 support, include the
.B Base6to4Interface
option in each prefix section. When using a dynamic IPv4 address, set
small prefix lifetimes to prevent hosts from retaining unreachable
prefixes after a new IPv4 address has been assigned.  When advertising to on
a dynamic interface (e.g., Bluetooth), skip the interface if it is not
active yet.

.nf
interface bnep0
{
        IgnoreIfMissing on;
        AdvSendAdvert on;

        # Advertise at least every 30 seconds
        MaxRtrAdvInterval 30;

        prefix 0:0:0:5678::/64
        {
                AdvOnLink on;
                AdvAutonomous on;
                Base6to4Interface ppp0;

                # Very short lifetimes for dynamic addresses
                AdvValidLifetime 300;
                AdvPreferredLifetime 120;
        };
};
.fi

Since 6to4 is enabled, the prefix will be advertised as
2002:WWXX:YYZZ:5678::/64, where WW.XX.YY.ZZ is the IPv4 address of
ppp0 at configuration time. (IPv6 addresses are written in hexadecimal
whereas IPv4 addresses are written in decimal, so the IPv4 address
WW.XX.YY.ZZ in the 6to4 prefix will be represented in hex.)

In this specific case, the configuration scripts may send HUP signal to
radvd when taking bnep0 up or down to notify about the status; in the
current radvd releases, sending HUP is no longer mandatory when the link
comes back up.

.nf
interface eth0
{
        AdvSendAdvert on;
        prefix 2001:db8:0:1::/64
        {
                AdvOnLink on;
                AdvAutonomous on;
        };
        clients
        {
                fe80::21f:16ff:fe06:3aab;
                fe80::21d:72ff:fe96:aaff;
        };
};
.fi

This configuration would only announce the prefix to fe80::21f:16ff:fe06:3aab and fe80::21d:72ff:fe96:aaff.
Furthermore, all RA requests of other clients are denied.

This may come in handy if you want to roll out IPv6 only partially because
some clients are broken or untested.

For ABRO support
.nf
interface lowpan0
{
	AdvSendAdvert on;
	UnicastOnly on;
	AdvCurHopLimit 255;
	prefix 2001:0db8:0100:f101::/64 {
		AdvOnLink on;
		AdvAutonomous on;
		AdvRouterAddr on;
	};
	abro fe80::a200:0:0:1/64 {
		AdvVersionLow 10;
		AdvVersionHigh 2;
		AdvValidLifetime 2;
	};
};

The NAT64 pref64 support
.nf
interface eth0
{
	prefix 2001:db8:100::/64 {
		AdvOnLink on;
		AdvAutonomous on;
		AdvRouterAddr on;
	};
	nat64prefix 64:ff9b::/96 {
		AdvValidLifetime 1800;
	};
	RDNSS 2001:db8:100::64 {
		AdvRDNSSLifetime 1800;
	};
};

.SH FILES

.nf
@sbindir@/radvd
@PATH_RADVD_CONF@
@PATH_RADVD_PID@
@PATH_RADVD_LOG@
.fi

.SH CREDIT
The description of the different flags and variables is in large
parts taken from RFC 4861.

.SH RFCS
Narten, T., Nordmark, E., Simpson, W., and H. Soliman, "Neighbor Discovery for IP
Version 6 (IPv6)", RFC 4861, September 2007.
.PP
Thomson, S., Narten, T., T. Jinmei, "IPv6 Stateless Address Autoconfiguration", 
RFC 4862, September 2007.
.PP
Deering, S., and R. Hinden, "IP Version 6 Addressing
Architecture", RFC 4291, February 2006.
.PP	
Conta, A., Deering, S., and M. Gupta "Internet Control Message Protocol (ICMPv6)
for the Internet Protocol Version 6 (IPv6)", RFC 4443, March 2006.
.PP
Crawford, M., "Transmission of IPv6 Packets over Ethernet Networks",
RFC 2464, December 1998.	
.PP
Carpenter B., K. Moore, "Connection of IPv6 Domains via IPv4 Clouds",
RFC 3056, February 2001. (6to4 specification)
.PP
Draves, R., D. Thaler, "Default Router Preferences and More-Specific Routes",
RFC 4191, November 2005.
.PP
Johnson, D., Perkins, C., and J. Arkko, "Mobility Support in IPv6",
RFC 3775, June 2004.
.PP
Devarapalli, V., Wakikawa, R., Petrescu, A., and P. Thubert "Network Mobility (NEMO) Basic Support Protocol",
RFC 3963, January 2005.
.PP
Z. Shelby, S. Chakrabarti, E. Nordmark and  C. Bormann " Neighbor Discovery Optimization for IPv6 over Low-Power 
Wireless Personal Area Networks (6LoWPANs)", RFC 6775, November 2012.
.PP
Gont, F. "Security Implications of IPv6 Fragmentation with IPv6 Neighbor Discovery",
RFC 6980, August 2013.
.PP
Yourtchenko, A. and Colitti, L. "Reducing Energy Consumption of Router Advertisements",
RFC 7772, February 2016.
.PP
J. Jeong, S. Park, L. Beloeil, and S. Madanapalli, "IPv6 Router Advertisement Options for DNS Configuration",
RFC 8106, March 2017.
L. Colitti, and J. Linkova, "Discovering PREF64 in Router Advertisements",
RFC 8781, April 2020.

.SH "SEE ALSO"

.BR radvd (8),
.BR radvdump (8)