Skip to content

Latest commit

 

History

History
202 lines (130 loc) · 3.96 KB

PRODUCTS.md

File metadata and controls

202 lines (130 loc) · 3.96 KB

List of IKEA TRÅDFRI products

Introduction

This list is a collection of the IKEA TRÅDFRI products, and their relevant technical properties. Please help me to update this list.

Lighting products

LED1545G12

Details:

  • Socket: E27
  • Potted: likely

LED1546G12

Details:

  • Socket: E27
  • Potted: likely

LED1622G12

Details:

  • Socket: E27
  • Potted: likely

LED1623G12

Details:

  • Socket: E27
  • Potted: likely

LED1624G9

Details:

  • Socket: E27
  • Potted: likely

LED1536G5

Details:

  • Socket: E14
  • Potted: likely

LED1537R6

Details:

  • Socket: GU10
  • Potted: yes (#3)

LED1650R5

Details:

  • Socket: GU10
  • Potted: no

TRÅDFRI Module pinout:

  • PA1 -> unused (but soldered)
  • PB13 -> LED driver

Power usage:

Brightness Power (W) Cos φ
100% 6.0 0.80
50% 1.6 0.62
10% 0.7 0.40
Off 0.0 1.00

Measured using a Voltcraft 3000 energy monitor.

Accessories

E1524 (Remote controller)

TRÅDFRI Module pinout:

  • PB15 -> Color temperature
  • PB14 -> Dim -
  • PC10 -> On/Off
  • PB13 -> TX
  • PA1 -> Dim +
  • PA0 -> TouchLink button

Source

E1525 (Motion sensor)

Details:

  • Battery: 2x CR2032

Pinout (unverified):

  • Time selection dial (R13): PA1 (Looks like a potentiometer between R12 high side and a FET to GND enabled directly by PB14.)

  • Day/night selection dial (R15): PB15 (Dito, with resistor R14 and same transistor.)

  • Pairing button (S1): Silicone rubber button puling PA0 directly to GND

  • The motion detection dome is connected (one pin directly, one indirectly) to an "E93196C 5090C 9A" labelled 8-pin chip to which also PC10 and PB14 are connected (needs further investigation).

  • Various test points:

    • VCC: TP8_1, TP8_2
    • GND: TP2_1, TP3_2
    • PB13: TP2_2
    • PA0: TP4_1, TP4_2
    • PA1: TP5_2

The module is easy to take apart, and debug wires can be soldered on without separating the radio / MCU PCB from the carrier PCB. The carrier board is labelled "D-Sensor-A1-01-A-V2.0".

E1526 (Gateway)

Details:

  • Power supply: USB 5V 1A

ICTC-G-1 (Wireless dimmer)

Pinout:

  • A0 - LED ON - TP7
  • A1 - BTN - TP6
  • B11 - FLASH CS
  • B12 - GYRO INT
  • B13 - FLASH VCC
  • B14 - ACC INT - TP8
  • B15 - GYRO ON - TP9
  • C10 - I2C SDA
  • C11 - I2C SCL
  • D13 - FLASH MCLK
  • D14 - FLASH MISO
  • D15 - FLASH MOSI
  • F0 - SWCLK - TP1
  • F1 - SWDIO - TP2
  • F2 - SWO - TP3
  • F3 - DBG - TP4
  •   RESET      - TP5

ICPSLC24-10NA (LED output controller/dimmer)

Details:

  • Potted: no

The output appears to be measured by the module somehow. Detailed PCB investigation required.

TRÅDFRI Module pinout (incomplete/unverified):

  • PA0: K1 (Reset key)
  • PA1: Goes to ZD1, through R9 and then to OUT+, possibly output measuring?
  • PB13: Pulls down the FET Gate
  • PF0: Pin 2 on header
  • PF1: Pin 3 on header

ICPSHC24-10EU-IL-1 (10W LED driver/dimmer)

10 Watt Power supply with the 24 V output being controlled by ICPSLC24-10NA

ICPSHC24-30EU-IL-1 (30W LED driver/dimmer)

30 Watt Power supply with the 24 V output being controlled by ICPSLC24-10NA

L1529 (FLOALT 60x60)

Details:

  • Potted: no

TRÅDFRI Module pinout (incomplete):

  • PA0: Pulse (not very readable)
  • PA1: PWM3 (not very readable)
  • PB1: PWM2
  • PB13: PWM1

L1527 (FLOALT 30x30)

Details:

  • Potted: no
  • 12.5W power supply/controller: PWIC012V24P

TRÅDFRI module pinout:

  • PA1: PWM for red (2200K) channel, from TIM1 CH0
  • PB12: PWM for blue (4000K) channel, from TIM1 CH1
  • other GPIO pads may be brought out from the module, but they're unused

Source Source