No ACCESS option on internal module

[NealM722]

Hello
I've just updated to EDGE TX on my FrSky Taranis QX7 Access TX.. When I scroll down to the internal RF option, I am only given the option to select "XJT".. There is no "ACCESS" option, which there used to be when I was using OpenTX..??

Can anyone advise where I've gone wrong ??? OR a possible solution ??

Here's what I've tried so far :

1. Flash firmware back to Open TX . . when I do this I get the ability to select ACCESS on the internal RF module. !! ??
2. When I go back to Edge TX again, I again loose the "ACCESS" option on the internal RF
3. I've downloaded and installed the latest version of the internal module firmware from the FRSky website, without success.

Thanks in advance..

[pfeerick]

Go to SYS -> HARDWARE, and down the bottom, change the internal RF type from XJT to ISRM. You should then be able to switch between OFF and ISRM for the internal RF.

…

On Sat, 28 Oct 2023, 12:54 am NealM722, ***@***.***> wrote: Hello I've just updated to EDGE TX on my FrSky Taranis QX7 Access TX.. When I scroll down to the internal RF option, I am only given the option to select "XJT".. There is no "ACCESS" option, which there used to be when I was using OpenTX..?? Can anyone advise where I've gone wrong ??? OR a possible solution ?? Here's what I've tried so far : 1. Flash firmware back to Open TX . . when I do this I get the ability to select ACCESS on the internal RF module. !! ?? 2. When I go back to Edge TX again, I again loose the "ACCESS" option on the internal RF 3. I've downloaded and installed the latest version of the internal module firmware from the FRSky website, without success. Thanks in advance.. — Reply to this email directly, view it on GitHub <#4255>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/ABJ66KLCSZ4YXGNZ2TAI4CDYBPDIRAVCNFSM6AAAAAA6S6N35KVHI2DSMVQWIX3LMV43ERDJONRXK43TNFXW4OZVG44DINRTGU> . You are receiving this because you are subscribed to this thread.Message ID: ***@***.***>

[NealM722]

Hello Many thanks for your reply . . . I'm pleased to report that this worked .. AGAIN , THANK YOU...

[pfeerick]

No problem, glad it's working for you now! 🥳

[NealM722]

Would you believe I spent most of yesterday trying to resolve that !!!! I'm very familiar with computer software, so was fairly sure it was going to be something that I'd missed, and also (probably); something fairly easy. But I just couldn't see it . . . Thanks again..

…

________________________________ From: Peter Feerick ***@***.***> Sent: 28 October 2023 9:27 AM To: EdgeTX/edgetx ***@***.***> Cc: NealM722 ***@***.***>; Author ***@***.***> Subject: Re: [EdgeTX/edgetx] No ACCESS option on internal module (Discussion #4255) No problem, glad it's working for you now! 🥳 — Reply to this email directly, view it on GitHub<#4255 (reply in thread)>, or unsubscribe<https://github.com/notifications/unsubscribe-auth/BDSE7U2PW4SCPVSGFAWAX73YBS6V7AVCNFSM6AAAAAA6S6N35KVHI2DSMVQWIX3LMV43SRDJONRXK43TNFXW4Q3PNVWWK3TUHM3TIMJQGEYTQ>. You are receiving this because you authored the thread.Message ID: ***@***.***>