Adjust FAST_PWM_FAN

MarlinFirmware/Marlin#23331
MarlinFirmware · Dec 23, 2021 · a24a1d7 · a24a1d7
1 parent 1805bb3
commit a24a1d7
Show file tree

Hide file tree

Showing 565 changed files with 5,380 additions and 3,309 deletions.
diff --git a/config/default/Configuration.h b/config/default/Configuration.h
@@ -2852,9 +2852,6 @@
 // :[1,2,3,4,5,6,7,8]
 //#define NUM_M106_FANS 1
 
-// Increase the FAN PWM frequency. Removes the PWM noise but increases heating in the FET/Arduino
-//#define FAST_PWM_FAN
-
 // Use software PWM to drive the fan, as for the heaters. This uses a very low frequency
 // which is not as annoying as with the hardware PWM. On the other hand, if this frequency
 // is too low, you should also increment SOFT_PWM_SCALE.

diff --git a/config/default/Configuration_adv.h b/config/default/Configuration_adv.h
@@ -549,18 +549,21 @@
 //#define FAN_MAX_PWM 128
 
 /**
- * FAST PWM FAN Settings
+ * Fan Fast PWM
  *
- * Use to change the FAST FAN PWM frequency (if enabled in Configuration.h)
- * Combinations of PWM Modes, prescale values and TOP resolutions are used internally to produce a
- * frequency as close as possible to the desired frequency.
+ * Combinations of PWM Modes, prescale values and TOP resolutions are used internally
+ * to produce a frequency as close as possible to the desired frequency.
  *
- * FAST_PWM_FAN_FREQUENCY [undefined by default]
+ * FAST_PWM_FAN_FREQUENCY
  *   Set this to your desired frequency.
- *   If left undefined this defaults to F = F_CPU/(2*255*1)
- *   i.e., F = 31.4kHz on 16MHz microcontrollers or F = 39.2kHz on 20MHz microcontrollers.
- *   These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
+ *   For AVR, if left undefined this defaults to F = F_CPU/(2*255*1)
+ *            i.e., F = 31.4kHz on 16MHz microcontrollers or F = 39.2kHz on 20MHz microcontrollers.
+ *   For non AVR, if left undefined this defaults to F = 1Khz.
+ *   This F value is only to protect the hardware from an absence of configuration
+ *   and not to complete it when users are not aware that the frequency must be specifically set to support the target board.
+ *
  *   NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
+ *         Setting very high frequencies can damage your hardware.
  *
  * USE_OCR2A_AS_TOP [undefined by default]
  *   Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
@@ -570,9 +573,17 @@
  *   PWM on pin OC2A. Only use this option if you don't need PWM on 0C2A. (Check your schematic.)
  *   USE_OCR2A_AS_TOP sacrifices duty cycle control resolution to achieve this broader range of frequencies.
  */
+//#define FAST_PWM_FAN    // Increase the fan PWM frequency. Removes the PWM noise but increases heating in the FET/Arduino
 #if ENABLED(FAST_PWM_FAN)
-  //#define FAST_PWM_FAN_FREQUENCY 31400
+  //#define FAST_PWM_FAN_FREQUENCY 31400  // Define here to override the defaults below
   //#define USE_OCR2A_AS_TOP
+  #ifndef FAST_PWM_FAN_FREQUENCY
+    #ifdef __AVR__
+      #define FAST_PWM_FAN_FREQUENCY ((F_CPU) / (2 * 255 * 1))
+    #else
+      #define FAST_PWM_FAN_FREQUENCY 1000U
+    #endif
+  #endif
 #endif
 
 /**

diff --git a/config/examples/3DFabXYZ/Migbot/Configuration.h b/config/examples/3DFabXYZ/Migbot/Configuration.h
@@ -2884,9 +2884,6 @@
 // :[1,2,3,4,5,6,7,8]
 //#define NUM_M106_FANS 1
 
-// Increase the FAN PWM frequency. Removes the PWM noise but increases heating in the FET/Arduino
-//#define FAST_PWM_FAN
-
 // Use software PWM to drive the fan, as for the heaters. This uses a very low frequency
 // which is not as annoying as with the hardware PWM. On the other hand, if this frequency
 // is too low, you should also increment SOFT_PWM_SCALE.

diff --git a/config/examples/3DFabXYZ/Migbot/Configuration_adv.h b/config/examples/3DFabXYZ/Migbot/Configuration_adv.h
@@ -549,18 +549,21 @@
 //#define FAN_MAX_PWM 128
 
 /**
- * FAST PWM FAN Settings
+ * Fan Fast PWM
  *
- * Use to change the FAST FAN PWM frequency (if enabled in Configuration.h)
- * Combinations of PWM Modes, prescale values and TOP resolutions are used internally to produce a
- * frequency as close as possible to the desired frequency.
+ * Combinations of PWM Modes, prescale values and TOP resolutions are used internally
+ * to produce a frequency as close as possible to the desired frequency.
  *
- * FAST_PWM_FAN_FREQUENCY [undefined by default]
+ * FAST_PWM_FAN_FREQUENCY
  *   Set this to your desired frequency.
- *   If left undefined this defaults to F = F_CPU/(2*255*1)
- *   i.e., F = 31.4kHz on 16MHz microcontrollers or F = 39.2kHz on 20MHz microcontrollers.
- *   These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
+ *   For AVR, if left undefined this defaults to F = F_CPU/(2*255*1)
+ *            i.e., F = 31.4kHz on 16MHz microcontrollers or F = 39.2kHz on 20MHz microcontrollers.
+ *   For non AVR, if left undefined this defaults to F = 1Khz.
+ *   This F value is only to protect the hardware from an absence of configuration
+ *   and not to complete it when users are not aware that the frequency must be specifically set to support the target board.
+ *
  *   NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
+ *         Setting very high frequencies can damage your hardware.
  *
  * USE_OCR2A_AS_TOP [undefined by default]
  *   Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
@@ -570,9 +573,17 @@
  *   PWM on pin OC2A. Only use this option if you don't need PWM on 0C2A. (Check your schematic.)
  *   USE_OCR2A_AS_TOP sacrifices duty cycle control resolution to achieve this broader range of frequencies.
  */
+//#define FAST_PWM_FAN    // Increase the fan PWM frequency. Removes the PWM noise but increases heating in the FET/Arduino
 #if ENABLED(FAST_PWM_FAN)
-  //#define FAST_PWM_FAN_FREQUENCY 31400
+  //#define FAST_PWM_FAN_FREQUENCY 31400  // Define here to override the defaults below
   //#define USE_OCR2A_AS_TOP
+  #ifndef FAST_PWM_FAN_FREQUENCY
+    #ifdef __AVR__
+      #define FAST_PWM_FAN_FREQUENCY ((F_CPU) / (2 * 255 * 1))
+    #else
+      #define FAST_PWM_FAN_FREQUENCY 1000U
+    #endif
+  #endif
 #endif
 
 /**

diff --git a/config/examples/ADIMLab/Gantry v1/Configuration.h b/config/examples/ADIMLab/Gantry v1/Configuration.h
@@ -2853,9 +2853,6 @@
 // :[1,2,3,4,5,6,7,8]
 //#define NUM_M106_FANS 1
 
-// Increase the FAN PWM frequency. Removes the PWM noise but increases heating in the FET/Arduino
-//#define FAST_PWM_FAN
-
 // Use software PWM to drive the fan, as for the heaters. This uses a very low frequency
 // which is not as annoying as with the hardware PWM. On the other hand, if this frequency
 // is too low, you should also increment SOFT_PWM_SCALE.

diff --git a/config/examples/ADIMLab/Gantry v1/Configuration_adv.h b/config/examples/ADIMLab/Gantry v1/Configuration_adv.h
@@ -549,18 +549,21 @@
 //#define FAN_MAX_PWM 128
 
 /**
- * FAST PWM FAN Settings
+ * Fan Fast PWM
  *
- * Use to change the FAST FAN PWM frequency (if enabled in Configuration.h)
- * Combinations of PWM Modes, prescale values and TOP resolutions are used internally to produce a
- * frequency as close as possible to the desired frequency.
+ * Combinations of PWM Modes, prescale values and TOP resolutions are used internally
+ * to produce a frequency as close as possible to the desired frequency.
  *
- * FAST_PWM_FAN_FREQUENCY [undefined by default]
+ * FAST_PWM_FAN_FREQUENCY
  *   Set this to your desired frequency.
- *   If left undefined this defaults to F = F_CPU/(2*255*1)
- *   i.e., F = 31.4kHz on 16MHz microcontrollers or F = 39.2kHz on 20MHz microcontrollers.
- *   These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
+ *   For AVR, if left undefined this defaults to F = F_CPU/(2*255*1)
+ *            i.e., F = 31.4kHz on 16MHz microcontrollers or F = 39.2kHz on 20MHz microcontrollers.
+ *   For non AVR, if left undefined this defaults to F = 1Khz.
+ *   This F value is only to protect the hardware from an absence of configuration
+ *   and not to complete it when users are not aware that the frequency must be specifically set to support the target board.
+ *
  *   NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
+ *         Setting very high frequencies can damage your hardware.
  *
  * USE_OCR2A_AS_TOP [undefined by default]
  *   Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
@@ -570,9 +573,17 @@
  *   PWM on pin OC2A. Only use this option if you don't need PWM on 0C2A. (Check your schematic.)
  *   USE_OCR2A_AS_TOP sacrifices duty cycle control resolution to achieve this broader range of frequencies.
  */
+//#define FAST_PWM_FAN    // Increase the fan PWM frequency. Removes the PWM noise but increases heating in the FET/Arduino
 #if ENABLED(FAST_PWM_FAN)
-  //#define FAST_PWM_FAN_FREQUENCY 31400
+  //#define FAST_PWM_FAN_FREQUENCY 31400  // Define here to override the defaults below
   //#define USE_OCR2A_AS_TOP
+  #ifndef FAST_PWM_FAN_FREQUENCY
+    #ifdef __AVR__
+      #define FAST_PWM_FAN_FREQUENCY ((F_CPU) / (2 * 255 * 1))
+    #else
+      #define FAST_PWM_FAN_FREQUENCY 1000U
+    #endif
+  #endif
 #endif
 
 /**

diff --git a/config/examples/ADIMLab/Gantry v2/Configuration.h b/config/examples/ADIMLab/Gantry v2/Configuration.h
@@ -2853,9 +2853,6 @@
 // :[1,2,3,4,5,6,7,8]
 //#define NUM_M106_FANS 1
 
-// Increase the FAN PWM frequency. Removes the PWM noise but increases heating in the FET/Arduino
-//#define FAST_PWM_FAN
-
 // Use software PWM to drive the fan, as for the heaters. This uses a very low frequency
 // which is not as annoying as with the hardware PWM. On the other hand, if this frequency
 // is too low, you should also increment SOFT_PWM_SCALE.

diff --git a/config/examples/ADIMLab/Gantry v2/Configuration_adv.h b/config/examples/ADIMLab/Gantry v2/Configuration_adv.h
@@ -549,18 +549,21 @@
 //#define FAN_MAX_PWM 128
 
 /**
- * FAST PWM FAN Settings
+ * Fan Fast PWM
  *
- * Use to change the FAST FAN PWM frequency (if enabled in Configuration.h)
- * Combinations of PWM Modes, prescale values and TOP resolutions are used internally to produce a
- * frequency as close as possible to the desired frequency.
+ * Combinations of PWM Modes, prescale values and TOP resolutions are used internally
+ * to produce a frequency as close as possible to the desired frequency.
  *
- * FAST_PWM_FAN_FREQUENCY [undefined by default]
+ * FAST_PWM_FAN_FREQUENCY
  *   Set this to your desired frequency.
- *   If left undefined this defaults to F = F_CPU/(2*255*1)
- *   i.e., F = 31.4kHz on 16MHz microcontrollers or F = 39.2kHz on 20MHz microcontrollers.
- *   These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
+ *   For AVR, if left undefined this defaults to F = F_CPU/(2*255*1)
+ *            i.e., F = 31.4kHz on 16MHz microcontrollers or F = 39.2kHz on 20MHz microcontrollers.
+ *   For non AVR, if left undefined this defaults to F = 1Khz.
+ *   This F value is only to protect the hardware from an absence of configuration
+ *   and not to complete it when users are not aware that the frequency must be specifically set to support the target board.
+ *
  *   NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
+ *         Setting very high frequencies can damage your hardware.
  *
  * USE_OCR2A_AS_TOP [undefined by default]
  *   Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
@@ -570,9 +573,17 @@
  *   PWM on pin OC2A. Only use this option if you don't need PWM on 0C2A. (Check your schematic.)
  *   USE_OCR2A_AS_TOP sacrifices duty cycle control resolution to achieve this broader range of frequencies.
  */
+//#define FAST_PWM_FAN    // Increase the fan PWM frequency. Removes the PWM noise but increases heating in the FET/Arduino
 #if ENABLED(FAST_PWM_FAN)
-  //#define FAST_PWM_FAN_FREQUENCY 31400
+  //#define FAST_PWM_FAN_FREQUENCY 31400  // Define here to override the defaults below
   //#define USE_OCR2A_AS_TOP
+  #ifndef FAST_PWM_FAN_FREQUENCY
+    #ifdef __AVR__
+      #define FAST_PWM_FAN_FREQUENCY ((F_CPU) / (2 * 255 * 1))
+    #else
+      #define FAST_PWM_FAN_FREQUENCY 1000U
+    #endif
+  #endif
 #endif
 
 /**

diff --git a/config/examples/Alfawise/U20-bltouch/Configuration.h b/config/examples/Alfawise/U20-bltouch/Configuration.h
@@ -2947,9 +2947,6 @@
 // :[1,2,3,4,5,6,7,8]
 //#define NUM_M106_FANS 1
 
-// Increase the FAN PWM frequency. Removes the PWM noise but increases heating in the FET/Arduino
-//#define FAST_PWM_FAN
-
 // Use software PWM to drive the fan, as for the heaters. This uses a very low frequency
 // which is not as annoying as with the hardware PWM. On the other hand, if this frequency
 // is too low, you should also increment SOFT_PWM_SCALE.

diff --git a/config/examples/Alfawise/U20-bltouch/Configuration_adv.h b/config/examples/Alfawise/U20-bltouch/Configuration_adv.h
@@ -549,18 +549,21 @@
 //#define FAN_MAX_PWM 128
 
 /**
- * FAST PWM FAN Settings
+ * Fan Fast PWM
  *
- * Use to change the FAST FAN PWM frequency (if enabled in Configuration.h)
- * Combinations of PWM Modes, prescale values and TOP resolutions are used internally to produce a
- * frequency as close as possible to the desired frequency.
+ * Combinations of PWM Modes, prescale values and TOP resolutions are used internally
+ * to produce a frequency as close as possible to the desired frequency.
  *
- * FAST_PWM_FAN_FREQUENCY [undefined by default]
+ * FAST_PWM_FAN_FREQUENCY
  *   Set this to your desired frequency.
- *   If left undefined this defaults to F = F_CPU/(2*255*1)
- *   i.e., F = 31.4kHz on 16MHz microcontrollers or F = 39.2kHz on 20MHz microcontrollers.
- *   These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
+ *   For AVR, if left undefined this defaults to F = F_CPU/(2*255*1)
+ *            i.e., F = 31.4kHz on 16MHz microcontrollers or F = 39.2kHz on 20MHz microcontrollers.
+ *   For non AVR, if left undefined this defaults to F = 1Khz.
+ *   This F value is only to protect the hardware from an absence of configuration
+ *   and not to complete it when users are not aware that the frequency must be specifically set to support the target board.
+ *
  *   NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
+ *         Setting very high frequencies can damage your hardware.
  *
  * USE_OCR2A_AS_TOP [undefined by default]
  *   Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
@@ -570,9 +573,17 @@
  *   PWM on pin OC2A. Only use this option if you don't need PWM on 0C2A. (Check your schematic.)
  *   USE_OCR2A_AS_TOP sacrifices duty cycle control resolution to achieve this broader range of frequencies.
  */
+#define FAST_PWM_FAN      // Increase the fan PWM frequency. Removes the PWM noise but increases heating in the FET/Arduino
 #if ENABLED(FAST_PWM_FAN)
-  //#define FAST_PWM_FAN_FREQUENCY 31400
+  #define FAST_PWM_FAN_FREQUENCY 31400    // Define here to override the defaults below
   //#define USE_OCR2A_AS_TOP
+  #ifndef FAST_PWM_FAN_FREQUENCY
+    #ifdef __AVR__
+      #define FAST_PWM_FAN_FREQUENCY ((F_CPU) / (2 * 255 * 1))
+    #else
+      #define FAST_PWM_FAN_FREQUENCY 1000U
+    #endif
+  #endif
 #endif
 
 /**

diff --git a/config/examples/Alfawise/U20/Configuration.h b/config/examples/Alfawise/U20/Configuration.h
@@ -2948,9 +2948,6 @@
 // :[1,2,3,4,5,6,7,8]
 //#define NUM_M106_FANS 1
 
-// Increase the FAN PWM frequency. Removes the PWM noise but increases heating in the FET/Arduino
-//#define FAST_PWM_FAN
-
 // Use software PWM to drive the fan, as for the heaters. This uses a very low frequency
 // which is not as annoying as with the hardware PWM. On the other hand, if this frequency
 // is too low, you should also increment SOFT_PWM_SCALE.

diff --git a/config/examples/Alfawise/U20/Configuration_adv.h b/config/examples/Alfawise/U20/Configuration_adv.h
@@ -549,18 +549,21 @@
 //#define FAN_MAX_PWM 128
 
 /**
- * FAST PWM FAN Settings
+ * Fan Fast PWM
  *
- * Use to change the FAST FAN PWM frequency (if enabled in Configuration.h)
- * Combinations of PWM Modes, prescale values and TOP resolutions are used internally to produce a
- * frequency as close as possible to the desired frequency.
+ * Combinations of PWM Modes, prescale values and TOP resolutions are used internally
+ * to produce a frequency as close as possible to the desired frequency.
  *
- * FAST_PWM_FAN_FREQUENCY [undefined by default]
+ * FAST_PWM_FAN_FREQUENCY
  *   Set this to your desired frequency.
- *   If left undefined this defaults to F = F_CPU/(2*255*1)
- *   i.e., F = 31.4kHz on 16MHz microcontrollers or F = 39.2kHz on 20MHz microcontrollers.
- *   These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
+ *   For AVR, if left undefined this defaults to F = F_CPU/(2*255*1)
+ *            i.e., F = 31.4kHz on 16MHz microcontrollers or F = 39.2kHz on 20MHz microcontrollers.
+ *   For non AVR, if left undefined this defaults to F = 1Khz.
+ *   This F value is only to protect the hardware from an absence of configuration
+ *   and not to complete it when users are not aware that the frequency must be specifically set to support the target board.
+ *
  *   NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
+ *         Setting very high frequencies can damage your hardware.
  *
  * USE_OCR2A_AS_TOP [undefined by default]
  *   Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
@@ -570,9 +573,17 @@
  *   PWM on pin OC2A. Only use this option if you don't need PWM on 0C2A. (Check your schematic.)
  *   USE_OCR2A_AS_TOP sacrifices duty cycle control resolution to achieve this broader range of frequencies.
  */
+#define FAST_PWM_FAN      // Increase the fan PWM frequency. Removes the PWM noise but increases heating in the FET/Arduino
 #if ENABLED(FAST_PWM_FAN)
-  //#define FAST_PWM_FAN_FREQUENCY 31400
+  #define FAST_PWM_FAN_FREQUENCY   31400  // Define here to override the defaults below
   //#define USE_OCR2A_AS_TOP
+  #ifndef FAST_PWM_FAN_FREQUENCY
+    #ifdef __AVR__
+      #define FAST_PWM_FAN_FREQUENCY ((F_CPU) / (2 * 255 * 1))
+    #else
+      #define FAST_PWM_FAN_FREQUENCY 1000U
+    #endif
+  #endif
 #endif
 
 /**

diff --git a/config/examples/AliExpress/CL-260/Configuration.h b/config/examples/AliExpress/CL-260/Configuration.h
@@ -2852,9 +2852,6 @@
 // :[1,2,3,4,5,6,7,8]
 //#define NUM_M106_FANS 1
 
-// Increase the FAN PWM frequency. Removes the PWM noise but increases heating in the FET/Arduino
-//#define FAST_PWM_FAN
-
 // Use software PWM to drive the fan, as for the heaters. This uses a very low frequency
 // which is not as annoying as with the hardware PWM. On the other hand, if this frequency
 // is too low, you should also increment SOFT_PWM_SCALE.

diff --git a/config/examples/AliExpress/UM2pExt/Configuration.h b/config/examples/AliExpress/UM2pExt/Configuration.h
@@ -2853,9 +2853,6 @@
 // :[1,2,3,4,5,6,7,8]
 //#define NUM_M106_FANS 1
 
-// Increase the FAN PWM frequency. Removes the PWM noise but increases heating in the FET/Arduino
-//#define FAST_PWM_FAN
-
 // Use software PWM to drive the fan, as for the heaters. This uses a very low frequency
 // which is not as annoying as with the hardware PWM. On the other hand, if this frequency
 // is too low, you should also increment SOFT_PWM_SCALE.