Getting Started with Seeed Studio XIAO ESP32C3 | Seeed Studio Wiki

[giscus[bot]]

Getting Started with Seeed Studio XIAO ESP32C3 | Seeed Studio Wiki

Getting Started with Seeed Studio XIAO ESP32C3

https://wiki.seeedstudio.com/XIAO_ESP32C3_Getting_Started/

[gbakerLV]

I am trying to flash Circuitpython via the "Open Installer" on https://circuitpython.org/board/seeed_xiao_esp32c3/ not working.

Just want to manually accomplish. Could you post the commands. thx

[gbakerLV]

Okay, I downloaded the "flash download tool 3.9.4".
I went back and forth flashing your "ESP...1014.bin" and the CircuitPython.
The tools said it was successful, but no CIRCUITPY drive.
Works okay with Ardiuino and your ".bin"
What am I missing

[vlkozl]

Url to [PDF] ESP32C3 datasheet is broken.

[MatthewJeffson]

Hi, I have messaged my colleague to fix it. Thank you for the notice!

[vlkozl]

Sorry, but where can I get info about how much power can I take from 5V, 3V3 and GPIO pins?
Thanks

[MatthewJeffson]

Hi, which kind of power are you looking for? Will this spec table can help you?

Parameter	Description
Power	Circuit operating voltage: 3.3V@200mA
Charging current: 50mA/100mA
Input voltage (VIN): 5V
Deep Sleep Power Consumption	Deep Sleep Model: >44 μA
Wi-Fi Enabled Power Consumption	Active Model: <75 mA
Modem-sleep Model: <25 mA
Light-sleep Model: <4 mA
BLE Enabled Power Consumption	Modem-sleep Model: <27 mA
Light-sleep Model: <10 mA
Working Temperature	-40°C ~ 85°C

[vlkozl]

Hi, not quite that.
How many amps, for example, an attached sensor can drain from 5V, from 3v3?

[MatthewJeffson]

Hi, you got me with this. :D Would you mind help to test it out and tell me? I couldn't be more grateful :)

[vlkozl]

Hi, sorry I'm a newbie in DIY electronics, only getting use to it.

[osmoralv]

Hi, I'm try to using the arduino BLE example codes and when I click on "Verify", Arduino IDE launch this error (for "XIAO ESP32C3 as Bluetooth server" code):

Compilation error: 'class BLECharacteristic' has no member named 'getValue'; did you mean 'setValue'?

[xadonxander]

The file listed as factory does not seem to be the right file. I flashed it and now all I get is a pop up that says device not recognized every time I plug it into the computer.

[newtocodi]

Can I use two of this board in ESPnow without connecting extra device or chip

[snowbrown]

Does this ESP32 XIAO have DAC pins and I could not fine these DAC pins in this website.

[snowbrown]

This ESP32 XAIO has only one DAC port.

[PabloGonzalezOrtega]

How we can change the Tx power to increse the range of BLE? In ESP32 especifications it says that the max. power is arounr 20dBm. In Arduino IDE I can't see anything about that.

Thanks!

[Stebar59]

Hi, I'm trying to configure the XIAO ESP32C3 for usage with the 24GHz mmWave Human Static Presence Module Lite.
I've followed the instruction and created the ESPhome yaml file but when I try to download it I have following error:

INFO Reading configuration /config/esphome/movimento1.yaml...
INFO Generating C++ source...
INFO Compiling app...
Processing movimento1 (board: esp32-c3-devkitm-1; framework: espidf; platform: platformio/espressif32 @ 5.3.0)

HARDWARE: ESP32C3 160MHz, 320KB RAM, 4MB Flash

• framework-espidf @ 3.40404.0 (4.4.4)
• tool-cmake @ 3.16.9
• tool-ninja @ 1.10.2
• toolchain-esp32ulp @ 2.35.0-20220830
• toolchain-riscv32-esp @ 8.4.0+2021r2-patch5
  Reading CMake configuration...
  -- The C compiler identification is GNU 8.4.0
  -- The CXX compiler identification is GNU 8.4.0
  -- The ASM compiler identification is GNU
  -- Found assembler: /data/cache/platformio/packages/toolchain-riscv32-esp/bin/riscv32-esp-elf-gcc
  -- Check for working C compiler: /data/cache/platformio/packages/toolchain-riscv32-esp/bin/riscv32-esp-elf-gcc
  -- Check for working C compiler: /data/cache/platformio/packages/toolchain-riscv32-esp/bin/riscv32-esp-elf-gcc -- broken
  -- Configuring incomplete, errors occurred!
  See also "/data/movimento1/.pioenvs/movimento1/CMakeFiles/CMakeOutput.log".
  See also "/data/movimento1/.pioenvs/movimento1/CMakeFiles/CMakeError.log".

fatal: not a git repository (or any parent up to mount point /)
Stopping at filesystem boundary (GIT_DISCOVERY_ACROSS_FILESYSTEM not set).
CMake Error at /data/cache/platformio/packages/tool-cmake/share/cmake-3.16/Modules/CMakeTestCCompiler.cmake:60 (message):
The C compiler

"/data/cache/platformio/packages/toolchain-riscv32-esp/bin/riscv32-esp-elf-gcc"

is not able to compile a simple test program.

It fails with the following output:

Change Dir: /data/movimento1/.pioenvs/movimento1/CMakeFiles/CMakeTmp

Run Build Command(s):/data/cache/platformio/packages/tool-ninja/ninja cmTC_919aa && [1/2] Building C object CMakeFiles/cmTC_919aa.dir/testCCompiler.c.obj
[2/2] Linking C executable cmTC_919aa
FAILED: cmTC_919aa 
: && /data/cache/platformio/packages/toolchain-riscv32-esp/bin/riscv32-esp-elf-gcc -march=rv32imc  -nostartfiles -march=rv32imc --specs=nosys.specs CMakeFiles/cmTC_919aa.dir/testCCompiler.c.obj  -o cmTC_919aa   && :
/data/cache/platformio/packages/toolchain-riscv32-esp/bin/../lib/gcc/riscv32-esp-elf/8.4.0/../../../../riscv32-esp-elf/bin/ld: /data/cache/platformio/packages/toolchain-riscv32-esp/bin/../libexec/gcc/riscv32-esp-elf/8.4.0/liblto_plugin.so: error loading plugin: /data/cache/platformio/packages/toolchain-riscv32-esp/bin/../libexec/gcc/riscv32-esp-elf/8.4.0/liblto_plugin.so: cannot open shared object file: No such file or directory
collect2: error: ld returned 1 exit status
ninja: build stopped: subcommand failed.

CMake will not be able to correctly generate this project.
Call Stack (most recent call first):
/data/cache/platformio/packages/framework-espidf/tools/cmake/project.cmake:296 (__project)
CMakeLists.txt:3 (project)

========================= [FAILED] Took 13.86 seconds =========================

Can someone please help me? I don't understand the error messages.
Many thanks

Stefano

[MatthewJeffson]

Welcome to our product documentation platform! We value user feedback and contributions, so we couldn’t be more grateful that you can help us improving the documentation.

Hence, if you find obvious errors in the product documentation, or you have additional ideas and insights about using products, please contribute to us.

If you need technical support, you can email it to [email protected].

If you want to discuss the product, I recommend the Seeed Studio Forum and Seeed Studio Discord Channel

The "Discussion channel" in Github here is a relatively new addition and may not receive much attention.

Nonetheless, we hope you find it helpful with the help of others. We will clean it up on a monthly basis.

[darekxan]

Does this board have a battery discharge cutoff voltage? Will it power down when battery gets discharged?

[numpad0]

Following this question. What exactly is this built in battery management situation? Is it from some unnamed chip or is this a clever software solution?

[BlackRose01]

Unfortunately, I recently had the problem that I always got the error "Write Timeout" after uploading my code. Flashing, as described in FAQ - Q3, also no longer worked. I got the same error. Therefore I had to do the following steps first:

1. connect pin 3.3V to D8
2. connect pin GND to D9

After that I could use the microcontroller again without any problems.

[BlackRose01]

Here is the source. Unfortunately only in German.
https://www.mikrocontroller.net/topic/562300

[msfujino]

I am having trouble uploading sketches.
I can upload sketches to two XIAOs without any problem, but I can't upload to one of them.
So I am trying to write the bootloader according to "Q3: I want to reflash the bootloader with factory firmware" on the Wiki, but it looks like the screenshot below and I can't write it.
It seems that the connection is made but the write timeout has occurred.

DEBUG:['COM3', 'COM5']
DEBUG:open com5 sucess
DEBUG:select test bin
DEBUG:Flash
DEBUG:['C:/ESP_TOOLS/EspRFTestTool_v3.6_Manual/ESP32-C3_RFTest_108_2b9b157_20211014.bin']
DEBUG:Com is closed ser0
DEBUG:close com sucessfully
ERROR:Write timeout
WARNING:Sync fail...

I have already confirmed the following
Connect to USB while holding down the boot switch
Remove the com port and reconnect it
Update the driver for the com port

Is there anything else I can try?

[BlackRose01]

Try this one:
#80 (comment)

[agahvcn]

"Is there a pin I can use to trigger a MOSFET in deep sleep mode?"

[nfs0619]

You can learn how to configure GPIO pins during deep sleep by reading the following documentation:

• ESP-IDF Programming Guide: Sleep Modes (ESP32-C3)

• ESP-IDF Programming Guide: Sleep Modes (ESP32)

[ruehlchris]

Hi,
Running in an issue with the external 5V supply. The Led show charging like plug in the USB
and the 3v3 Pin is up too. But the board is not starting. I plug the USB - with and without CDC enabled
and everything comes alive.
Is the 5V input only to charge a battery and supply 3v3?
Please clarify, and if so - you may update the description in the Getting Started..

My project I use the esp32c3 to replace a toy's RC car malfunction remote control with GATT-server/client.

Chris

[msfujino]

Is there a "while(!Serial);" in your sketch?
If so, remove it and it will work without USB.

[ruehlchris]

no such while() in my code. That was my first thing thinking that the code hang in a Terminal ready wait loop.

[msfujino]

According to the schematic, the 5V pin and the USB 5V are connected internally, so unless the two are connected at the same time, the problem should not occur.
Also, the ESP32C3 consumes a lot of current when the radio is enabled (over 200mA peak), and I am concerned about whether the external 5V power supply can supply the current properly.

[ruehlchris]

I got the supply from 3V power line from the RC car's PCBA and have a 2A power up stepper to 5.1V. The supply is stable.
I'm checking gpio9 and gpio2 for SPI boot must have pull up , have a weak pull up soldered from 3v3 -> gpio2 (D0)
gpio9 is untouched and 3v3. Still no boot.

[ruehlchris]

Found it! It's a problem with the power-rail on the PCBA from the RC-car. There is current limiter and when I start the board the output voltage drops to 1.8V on that rail.
I need to fix this. I get back to you.

[ruehlchris]

OK,
short update. I have build the Remote control unit with a Li-Po battery and it works flawless with & w/o CDC enabled.
I waiting now for a MPS (input 7.5~28V output 5V/1.6A) which then connect to the unlimited 9V rail of the RC-Car's supply.

[nfs0619]

Thank you for sharing! We’re excited to welcome you to contribute to our project.

If you're interested in learning more about how to get involved or contribute, feel free to check out the links below for more information:

• Contributor Introduction
• Contributor Project Page

We look forward to more interactions and collaboration with you!

[jkyumekamui]

Does ESP32 C3 really have FPU?
I didn't see anything about FPU in the ESP32 C3 datasheet and it is mentioned in 4.1.1 in the ESP32 one. According to API guides of ESP32 C3, floating point arithmetic are emulated in software and are very slow.

[nfs0619]

Thank you very much for your feedback, and we apologize for the confusion. The XIAO ESP32 C3 does not have a built-in FPU. We have already corrected the issue in the wiki documentation, and we truly appreciate you pointing this out. As you mentioned, floating point operations are emulated in software on the XIAO ESP32 C3, which can lead to slower performance. We appreciate your understanding and support!

[GeGou]

Hi, I am trying to co next a neo 6m gos module and a sim800l module. Gos module is connected to TX RX pins and works fine, but I cannot make gprs module to work using pins D9 D10. I have already try the same in a lolin esp32 c3 board and there works, I use the same code with xiao and doesn't work. Any suggestion please;

[nfs0619]

Hi, if you want to use D9 and D10 as a serial port to communicate with the SIM800L module, you need to use the SoftwareSerial library. Please make sure your code correctly utilizes this library.

If you have any further questions, feel free to contact our technical support at [email protected].

[GeGou]

Hi , thank you for the reply , i have try what i saw from this thread https://forum.seeedstudio.com/t/xiao-esp32c3-multiple-software-serial-ports/291155/38 but still cannot make it run. i have paste the simple code i am trying to run. I testes it with lolin c3 super mini board and it works, means that passwords, usernames and apns are correct. If you can make some changes to test it again i will be very thankful. Comments are in greek, that maybe be a problem.
New Text Document.txt

[GeGou]

Finally I solve the problem by using hardwareSerial on pins gpio6 and gpio7 if I remember correct.

[Shivang1303]

i am getting an issue when i am trying to power up my xiao esp32c3 and esp32c6 using a 5V power supply
i have tested current limit from 40mA to 120mA, every time i try to power it via VUSB pin, the current drawn from power supply fluctuates, and i am not able to detect it in ble mode

i have even tried using a diode between the vusb pin and power supply, and when i was powering it with USB cable, i checked the current drawn was around 69mA for c6 and 76mA for c3

please help me troubbleshoot this issue

[Shivang1303]

and also, the red led constantly blinks when powering with external power supply, but both the boards work perfectly with usb cable

[nfs0619]

Hello, we do not recommend powering the board directly via the VUSB pin, as this may cause unstable current issues. Additionally, if a Type-C cable is connected at the same time, it could damage the board. We recommend using the Battery Connector pin on the back of the board for a safer and more stable power supply.