Deb packages #42
Comments
|
For the time being there are no plans to provide pre built variants of this projects in an apt repository. Maybe at a later point when i setup github sponsors and get a bit of funding that allows me to invest more time, but right now this is not feasible as it would also add a lot of non core hardened related time investment like general purpose feature Kconfig change requests and all sort of other time consuming problems. |
anthraxx
pushed a commit
that referenced
this issue
Oct 20, 2021
commit 4d4a223 upstream. Commit 4dd0d5c ("ice: add lock around Tx timestamp tracker flush") added a lock around the Tx timestamp tracker flow which is used to cleanup any left over SKBs and prepare for device removal. This lock is problematic because it is being held around a call to ice_clear_phy_tstamp. The clear function takes a mutex to send a PHY write command to firmware. This could lead to a deadlock if the mutex actually sleeps, and causes the following warning on a kernel with preemption debugging enabled: [ 715.419426] BUG: sleeping function called from invalid context at kernel/locking/mutex.c:573 [ 715.427900] in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 3100, name: rmmod [ 715.435652] INFO: lockdep is turned off. [ 715.439591] Preemption disabled at: [ 715.439594] [<0000000000000000>] 0x0 [ 715.446678] CPU: 52 PID: 3100 Comm: rmmod Tainted: G W OE 5.15.0-rc4+ #42 bdd7ec3018e725f159ca0d372ce8c2c0e784891c [ 715.458058] Hardware name: Intel Corporation S2600STQ/S2600STQ, BIOS SE5C620.86B.02.01.0010.010620200716 01/06/2020 [ 715.468483] Call Trace: [ 715.470940] dump_stack_lvl+0x6a/0x9a [ 715.474613] ___might_sleep.cold+0x224/0x26a [ 715.478895] __mutex_lock+0xb3/0x1440 [ 715.482569] ? stack_depot_save+0x378/0x500 [ 715.486763] ? ice_sq_send_cmd+0x78/0x14c0 [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d] [ 715.494979] ? kfree+0xc1/0x520 [ 715.498128] ? mutex_lock_io_nested+0x12a0/0x12a0 [ 715.502837] ? kasan_set_free_info+0x20/0x30 [ 715.507110] ? __kasan_slab_free+0x10b/0x140 [ 715.511385] ? slab_free_freelist_hook+0xc7/0x220 [ 715.516092] ? kfree+0xc1/0x520 [ 715.519235] ? ice_deinit_lag+0x16c/0x220 [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d] [ 715.527359] ? ice_remove+0x1cf/0x6a0 [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d] [ 715.535133] ? pci_device_remove+0xab/0x1d0 [ 715.539318] ? __device_release_driver+0x35b/0x690 [ 715.544110] ? driver_detach+0x214/0x2f0 [ 715.548035] ? bus_remove_driver+0x11d/0x2f0 [ 715.552309] ? pci_unregister_driver+0x26/0x250 [ 715.556840] ? ice_module_exit+0xc/0x2f [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d] [ 715.564799] ? __do_sys_delete_module.constprop.0+0x2d8/0x4e0 [ 715.570554] ? do_syscall_64+0x3b/0x90 [ 715.574303] ? entry_SYSCALL_64_after_hwframe+0x44/0xae [ 715.579529] ? start_flush_work+0x542/0x8f0 [ 715.583719] ? ice_sq_send_cmd+0x78/0x14c0 [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d] [ 715.591923] ice_sq_send_cmd+0x78/0x14c0 [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d] [ 715.599960] ? wait_for_completion_io+0x250/0x250 [ 715.604662] ? lock_acquire+0x196/0x200 [ 715.608504] ? do_raw_spin_trylock+0xa5/0x160 [ 715.612864] ice_sbq_rw_reg+0x1e6/0x2f0 [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d] [ 715.620813] ? ice_reset+0x130/0x130 [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d] [ 715.628497] ? __debug_check_no_obj_freed+0x1e8/0x3c0 [ 715.633550] ? trace_hardirqs_on+0x1c/0x130 [ 715.637748] ice_write_phy_reg_e810+0x70/0xf0 [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d] [ 715.646220] ? do_raw_spin_trylock+0xa5/0x160 [ 715.650581] ? ice_ptp_release+0x910/0x910 [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d] [ 715.658797] ? ice_ptp_release+0x255/0x910 [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d] [ 715.667013] ice_clear_phy_tstamp+0x2c/0x110 [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d] [ 715.675403] ice_ptp_release+0x408/0x910 [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d] [ 715.683440] ice_remove+0x560/0x6a0 [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d] [ 715.691037] ? _raw_spin_unlock_irqrestore+0x46/0x73 [ 715.696005] pci_device_remove+0xab/0x1d0 [ 715.700018] __device_release_driver+0x35b/0x690 [ 715.704637] driver_detach+0x214/0x2f0 [ 715.708389] bus_remove_driver+0x11d/0x2f0 [ 715.712489] pci_unregister_driver+0x26/0x250 [ 715.716857] ice_module_exit+0xc/0x2f [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d] [ 715.724637] __do_sys_delete_module.constprop.0+0x2d8/0x4e0 [ 715.730210] ? free_module+0x6d0/0x6d0 [ 715.733963] ? task_work_run+0xe1/0x170 [ 715.737803] ? exit_to_user_mode_loop+0x17f/0x1d0 [ 715.742509] ? rcu_read_lock_sched_held+0x12/0x80 [ 715.747215] ? trace_hardirqs_on+0x1c/0x130 [ 715.751401] do_syscall_64+0x3b/0x90 [ 715.754981] entry_SYSCALL_64_after_hwframe+0x44/0xae [ 715.760033] RIP: 0033:0x7f4dfe59000b [ 715.763612] Code: 73 01 c3 48 8b 0d 6d 1e 0c 00 f7 d8 64 89 01 48 83 c8 ff c3 66 2e 0f 1f 84 00 00 00 00 00 90 f3 0f 1e fa b8 b0 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 3d 1e 0c 00 f7 d8 64 89 01 48 [ 715.782357] RSP: 002b:00007ffe8c891708 EFLAGS: 00000206 ORIG_RAX: 00000000000000b0 [ 715.789923] RAX: ffffffffffffffda RBX: 00005558a20468b0 RCX: 00007f4dfe59000b [ 715.797054] RDX: 000000000000000a RSI: 0000000000000800 RDI: 00005558a2046918 [ 715.804189] RBP: 0000000000000000 R08: 0000000000000000 R09: 0000000000000000 [ 715.811319] R10: 00007f4dfe603ac0 R11: 0000000000000206 R12: 00007ffe8c891940 [ 715.818455] R13: 00007ffe8c8920a3 R14: 00005558a20462a0 R15: 00005558a20468b0 Notice that this is the only case where we use the lock in this way. In the cleanup kthread and work kthread the lock is only taken around the bit accesses. This was done intentionally to avoid this kind of issue. The way the lock is used, we only protect ordering of bit sets vs bit clears. The Tx writers in the hot path don't need to be protected against the entire kthread loop. The Tx queues threads only need to ensure that they do not re-use an index that is currently in use. The cleanup loop does not need to block all new set bits, since it will re-queue itself if new timestamps are present. Fix the tracker flow so that it uses the same flow as the standard cleanup thread. In addition, ensure the in_use bitmap actually gets cleared properly. This fixes the warning and also avoids the potential deadlock that might have occurred otherwise. Fixes: 4dd0d5c ("ice: add lock around Tx timestamp tracker flush") Signed-off-by: Jacob Keller <[email protected]> Signed-off-by: Tony Nguyen <[email protected]> Signed-off-by: David S. Miller <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
anthraxx
pushed a commit
that referenced
this issue
Nov 10, 2021
Commit 4dd0d5c ("ice: add lock around Tx timestamp tracker flush") added a lock around the Tx timestamp tracker flow which is used to cleanup any left over SKBs and prepare for device removal. This lock is problematic because it is being held around a call to ice_clear_phy_tstamp. The clear function takes a mutex to send a PHY write command to firmware. This could lead to a deadlock if the mutex actually sleeps, and causes the following warning on a kernel with preemption debugging enabled: [ 715.419426] BUG: sleeping function called from invalid context at kernel/locking/mutex.c:573 [ 715.427900] in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 3100, name: rmmod [ 715.435652] INFO: lockdep is turned off. [ 715.439591] Preemption disabled at: [ 715.439594] [<0000000000000000>] 0x0 [ 715.446678] CPU: 52 PID: 3100 Comm: rmmod Tainted: G W OE 5.15.0-rc4+ #42 bdd7ec3018e725f159ca0d372ce8c2c0e784891c [ 715.458058] Hardware name: Intel Corporation S2600STQ/S2600STQ, BIOS SE5C620.86B.02.01.0010.010620200716 01/06/2020 [ 715.468483] Call Trace: [ 715.470940] dump_stack_lvl+0x6a/0x9a [ 715.474613] ___might_sleep.cold+0x224/0x26a [ 715.478895] __mutex_lock+0xb3/0x1440 [ 715.482569] ? stack_depot_save+0x378/0x500 [ 715.486763] ? ice_sq_send_cmd+0x78/0x14c0 [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d] [ 715.494979] ? kfree+0xc1/0x520 [ 715.498128] ? mutex_lock_io_nested+0x12a0/0x12a0 [ 715.502837] ? kasan_set_free_info+0x20/0x30 [ 715.507110] ? __kasan_slab_free+0x10b/0x140 [ 715.511385] ? slab_free_freelist_hook+0xc7/0x220 [ 715.516092] ? kfree+0xc1/0x520 [ 715.519235] ? ice_deinit_lag+0x16c/0x220 [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d] [ 715.527359] ? ice_remove+0x1cf/0x6a0 [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d] [ 715.535133] ? pci_device_remove+0xab/0x1d0 [ 715.539318] ? __device_release_driver+0x35b/0x690 [ 715.544110] ? driver_detach+0x214/0x2f0 [ 715.548035] ? bus_remove_driver+0x11d/0x2f0 [ 715.552309] ? pci_unregister_driver+0x26/0x250 [ 715.556840] ? ice_module_exit+0xc/0x2f [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d] [ 715.564799] ? __do_sys_delete_module.constprop.0+0x2d8/0x4e0 [ 715.570554] ? do_syscall_64+0x3b/0x90 [ 715.574303] ? entry_SYSCALL_64_after_hwframe+0x44/0xae [ 715.579529] ? start_flush_work+0x542/0x8f0 [ 715.583719] ? ice_sq_send_cmd+0x78/0x14c0 [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d] [ 715.591923] ice_sq_send_cmd+0x78/0x14c0 [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d] [ 715.599960] ? wait_for_completion_io+0x250/0x250 [ 715.604662] ? lock_acquire+0x196/0x200 [ 715.608504] ? do_raw_spin_trylock+0xa5/0x160 [ 715.612864] ice_sbq_rw_reg+0x1e6/0x2f0 [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d] [ 715.620813] ? ice_reset+0x130/0x130 [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d] [ 715.628497] ? __debug_check_no_obj_freed+0x1e8/0x3c0 [ 715.633550] ? trace_hardirqs_on+0x1c/0x130 [ 715.637748] ice_write_phy_reg_e810+0x70/0xf0 [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d] [ 715.646220] ? do_raw_spin_trylock+0xa5/0x160 [ 715.650581] ? ice_ptp_release+0x910/0x910 [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d] [ 715.658797] ? ice_ptp_release+0x255/0x910 [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d] [ 715.667013] ice_clear_phy_tstamp+0x2c/0x110 [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d] [ 715.675403] ice_ptp_release+0x408/0x910 [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d] [ 715.683440] ice_remove+0x560/0x6a0 [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d] [ 715.691037] ? _raw_spin_unlock_irqrestore+0x46/0x73 [ 715.696005] pci_device_remove+0xab/0x1d0 [ 715.700018] __device_release_driver+0x35b/0x690 [ 715.704637] driver_detach+0x214/0x2f0 [ 715.708389] bus_remove_driver+0x11d/0x2f0 [ 715.712489] pci_unregister_driver+0x26/0x250 [ 715.716857] ice_module_exit+0xc/0x2f [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d] [ 715.724637] __do_sys_delete_module.constprop.0+0x2d8/0x4e0 [ 715.730210] ? free_module+0x6d0/0x6d0 [ 715.733963] ? task_work_run+0xe1/0x170 [ 715.737803] ? exit_to_user_mode_loop+0x17f/0x1d0 [ 715.742509] ? rcu_read_lock_sched_held+0x12/0x80 [ 715.747215] ? trace_hardirqs_on+0x1c/0x130 [ 715.751401] do_syscall_64+0x3b/0x90 [ 715.754981] entry_SYSCALL_64_after_hwframe+0x44/0xae [ 715.760033] RIP: 0033:0x7f4dfe59000b [ 715.763612] Code: 73 01 c3 48 8b 0d 6d 1e 0c 00 f7 d8 64 89 01 48 83 c8 ff c3 66 2e 0f 1f 84 00 00 00 00 00 90 f3 0f 1e fa b8 b0 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 3d 1e 0c 00 f7 d8 64 89 01 48 [ 715.782357] RSP: 002b:00007ffe8c891708 EFLAGS: 00000206 ORIG_RAX: 00000000000000b0 [ 715.789923] RAX: ffffffffffffffda RBX: 00005558a20468b0 RCX: 00007f4dfe59000b [ 715.797054] RDX: 000000000000000a RSI: 0000000000000800 RDI: 00005558a2046918 [ 715.804189] RBP: 0000000000000000 R08: 0000000000000000 R09: 0000000000000000 [ 715.811319] R10: 00007f4dfe603ac0 R11: 0000000000000206 R12: 00007ffe8c891940 [ 715.818455] R13: 00007ffe8c8920a3 R14: 00005558a20462a0 R15: 00005558a20468b0 Notice that this is the only case where we use the lock in this way. In the cleanup kthread and work kthread the lock is only taken around the bit accesses. This was done intentionally to avoid this kind of issue. The way the lock is used, we only protect ordering of bit sets vs bit clears. The Tx writers in the hot path don't need to be protected against the entire kthread loop. The Tx queues threads only need to ensure that they do not re-use an index that is currently in use. The cleanup loop does not need to block all new set bits, since it will re-queue itself if new timestamps are present. Fix the tracker flow so that it uses the same flow as the standard cleanup thread. In addition, ensure the in_use bitmap actually gets cleared properly. This fixes the warning and also avoids the potential deadlock that might have occurred otherwise. Fixes: 4dd0d5c ("ice: add lock around Tx timestamp tracker flush") Signed-off-by: Jacob Keller <[email protected]> Signed-off-by: Tony Nguyen <[email protected]> Signed-off-by: David S. Miller <[email protected]>
anthraxx
pushed a commit
that referenced
this issue
Aug 17, 2022
commit 59c026c upstream. When use 'echo c > /proc/sysrq-trigger' to trigger kdump, riscv_crash_save_regs() will be called to save regs for vmcore, we found "epc" value 00ffffffa5537400 is not a valid kernel virtual address, but is a user virtual address. Other regs(eg, ra, sp, gp...) are correct kernel virtual address. Actually 0x00ffffffb0dd9400 is the user mode PC of 'PID: 113 Comm: sh', which is saved in the task's stack. [ 21.201701] CPU: 0 PID: 113 Comm: sh Kdump: loaded Not tainted 5.18.9 #45 [ 21.201979] Hardware name: riscv-virtio,qemu (DT) [ 21.202160] epc : 00ffffffa5537400 ra : ffffffff80088640 sp : ff20000010333b90 [ 21.202435] gp : ffffffff810dde38 tp : ff6000000226c200 t0 : ffffffff8032be7c [ 21.202707] t1 : 0720072007200720 t2 : 30203a7375746174 s0 : ff20000010333cf0 [ 21.202973] s1 : 0000000000000000 a0 : ff20000010333b98 a1 : 0000000000000001 [ 21.203243] a2 : 0000000000000010 a3 : 0000000000000000 a4 : 28c8f0aeffea4e00 [ 21.203519] a5 : 28c8f0aeffea4e00 a6 : 0000000000000009 a7 : ffffffff8035c9b8 [ 21.203794] s2 : ffffffff810df0a8 s3 : ffffffff810df718 s4 : ff20000010333b98 [ 21.204062] s5 : 0000000000000000 s6 : 0000000000000007 s7 : ffffffff80c4a468 [ 21.204331] s8 : 00ffffffef451410 s9 : 0000000000000007 s10: 00aaaaaac0510700 [ 21.204606] s11: 0000000000000001 t3 : ff60000001218f00 t4 : ff60000001218f00 [ 21.204876] t5 : ff60000001218000 t6 : ff200000103338b8 [ 21.205079] status: 0000000200000020 badaddr: 0000000000000000 cause: 0000000000000008 With the incorrect PC, the backtrace showed by crash tool as below, the first stack frame is abnormal, crash> bt PID: 113 TASK: ff60000002269600 CPU: 0 COMMAND: "sh" #0 [ff2000001039bb90] __efistub_.Ldebug_info0 at 00ffffffa5537400 <-- Abnormal #1 [ff2000001039bcf0] panic at ffffffff806578ba #2 [ff2000001039bd50] sysrq_reset_seq_param_set at ffffffff8038c030 #3 [ff2000001039bda0] __handle_sysrq at ffffffff8038c5f8 #4 [ff2000001039be00] write_sysrq_trigger at ffffffff8038cad8 #5 [ff2000001039be20] proc_reg_write at ffffffff801b7edc #6 [ff2000001039be40] vfs_write at ffffffff80152ba6 #7 [ff2000001039be80] ksys_write at ffffffff80152ece #8 [ff2000001039bed0] sys_write at ffffffff80152f46 With the patch, we can get current kernel mode PC, the output as below, [ 17.607658] CPU: 0 PID: 113 Comm: sh Kdump: loaded Not tainted 5.18.9 #42 [ 17.607937] Hardware name: riscv-virtio,qemu (DT) [ 17.608150] epc : ffffffff800078f8 ra : ffffffff8008862c sp : ff20000010333b90 [ 17.608441] gp : ffffffff810dde38 tp : ff6000000226c200 t0 : ffffffff8032be68 [ 17.608741] t1 : 0720072007200720 t2 : 666666666666663c s0 : ff20000010333cf0 [ 17.609025] s1 : 0000000000000000 a0 : ff20000010333b98 a1 : 0000000000000001 [ 17.609320] a2 : 0000000000000010 a3 : 0000000000000000 a4 : 0000000000000000 [ 17.609601] a5 : ff60000001c78000 a6 : 000000000000003c a7 : ffffffff8035c9a4 [ 17.609894] s2 : ffffffff810df0a8 s3 : ffffffff810df718 s4 : ff20000010333b98 [ 17.610186] s5 : 0000000000000000 s6 : 0000000000000007 s7 : ffffffff80c4a468 [ 17.610469] s8 : 00ffffffca281410 s9 : 0000000000000007 s10: 00aaaaaab5bb6700 [ 17.610755] s11: 0000000000000001 t3 : ff60000001218f00 t4 : ff60000001218f00 [ 17.611041] t5 : ff60000001218000 t6 : ff20000010333988 [ 17.611255] status: 0000000200000020 badaddr: 0000000000000000 cause: 0000000000000008 With the correct PC, the backtrace showed by crash tool as below, crash> bt PID: 113 TASK: ff6000000226c200 CPU: 0 COMMAND: "sh" #0 [ff20000010333b90] riscv_crash_save_regs at ffffffff800078f8 <--- Normal #1 [ff20000010333cf0] panic at ffffffff806578c6 #2 [ff20000010333d50] sysrq_reset_seq_param_set at ffffffff8038c03c #3 [ff20000010333da0] __handle_sysrq at ffffffff8038c604 #4 [ff20000010333e00] write_sysrq_trigger at ffffffff8038cae4 #5 [ff20000010333e20] proc_reg_write at ffffffff801b7ee8 #6 [ff20000010333e40] vfs_write at ffffffff80152bb2 #7 [ff20000010333e80] ksys_write at ffffffff80152eda #8 [ff20000010333ed0] sys_write at ffffffff80152f52 Fixes: e53d281 ("RISC-V: Add kdump support") Co-developed-by: Guo Ren <[email protected]> Signed-off-by: Xianting Tian <[email protected]> Link: https://lore.kernel.org/r/[email protected] Cc: [email protected] Signed-off-by: Palmer Dabbelt <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
anthraxx
pushed a commit
that referenced
this issue
Aug 17, 2022
commit 59c026c upstream. When use 'echo c > /proc/sysrq-trigger' to trigger kdump, riscv_crash_save_regs() will be called to save regs for vmcore, we found "epc" value 00ffffffa5537400 is not a valid kernel virtual address, but is a user virtual address. Other regs(eg, ra, sp, gp...) are correct kernel virtual address. Actually 0x00ffffffb0dd9400 is the user mode PC of 'PID: 113 Comm: sh', which is saved in the task's stack. [ 21.201701] CPU: 0 PID: 113 Comm: sh Kdump: loaded Not tainted 5.18.9 #45 [ 21.201979] Hardware name: riscv-virtio,qemu (DT) [ 21.202160] epc : 00ffffffa5537400 ra : ffffffff80088640 sp : ff20000010333b90 [ 21.202435] gp : ffffffff810dde38 tp : ff6000000226c200 t0 : ffffffff8032be7c [ 21.202707] t1 : 0720072007200720 t2 : 30203a7375746174 s0 : ff20000010333cf0 [ 21.202973] s1 : 0000000000000000 a0 : ff20000010333b98 a1 : 0000000000000001 [ 21.203243] a2 : 0000000000000010 a3 : 0000000000000000 a4 : 28c8f0aeffea4e00 [ 21.203519] a5 : 28c8f0aeffea4e00 a6 : 0000000000000009 a7 : ffffffff8035c9b8 [ 21.203794] s2 : ffffffff810df0a8 s3 : ffffffff810df718 s4 : ff20000010333b98 [ 21.204062] s5 : 0000000000000000 s6 : 0000000000000007 s7 : ffffffff80c4a468 [ 21.204331] s8 : 00ffffffef451410 s9 : 0000000000000007 s10: 00aaaaaac0510700 [ 21.204606] s11: 0000000000000001 t3 : ff60000001218f00 t4 : ff60000001218f00 [ 21.204876] t5 : ff60000001218000 t6 : ff200000103338b8 [ 21.205079] status: 0000000200000020 badaddr: 0000000000000000 cause: 0000000000000008 With the incorrect PC, the backtrace showed by crash tool as below, the first stack frame is abnormal, crash> bt PID: 113 TASK: ff60000002269600 CPU: 0 COMMAND: "sh" #0 [ff2000001039bb90] __efistub_.Ldebug_info0 at 00ffffffa5537400 <-- Abnormal #1 [ff2000001039bcf0] panic at ffffffff806578ba #2 [ff2000001039bd50] sysrq_reset_seq_param_set at ffffffff8038c030 #3 [ff2000001039bda0] __handle_sysrq at ffffffff8038c5f8 #4 [ff2000001039be00] write_sysrq_trigger at ffffffff8038cad8 #5 [ff2000001039be20] proc_reg_write at ffffffff801b7edc #6 [ff2000001039be40] vfs_write at ffffffff80152ba6 #7 [ff2000001039be80] ksys_write at ffffffff80152ece #8 [ff2000001039bed0] sys_write at ffffffff80152f46 With the patch, we can get current kernel mode PC, the output as below, [ 17.607658] CPU: 0 PID: 113 Comm: sh Kdump: loaded Not tainted 5.18.9 #42 [ 17.607937] Hardware name: riscv-virtio,qemu (DT) [ 17.608150] epc : ffffffff800078f8 ra : ffffffff8008862c sp : ff20000010333b90 [ 17.608441] gp : ffffffff810dde38 tp : ff6000000226c200 t0 : ffffffff8032be68 [ 17.608741] t1 : 0720072007200720 t2 : 666666666666663c s0 : ff20000010333cf0 [ 17.609025] s1 : 0000000000000000 a0 : ff20000010333b98 a1 : 0000000000000001 [ 17.609320] a2 : 0000000000000010 a3 : 0000000000000000 a4 : 0000000000000000 [ 17.609601] a5 : ff60000001c78000 a6 : 000000000000003c a7 : ffffffff8035c9a4 [ 17.609894] s2 : ffffffff810df0a8 s3 : ffffffff810df718 s4 : ff20000010333b98 [ 17.610186] s5 : 0000000000000000 s6 : 0000000000000007 s7 : ffffffff80c4a468 [ 17.610469] s8 : 00ffffffca281410 s9 : 0000000000000007 s10: 00aaaaaab5bb6700 [ 17.610755] s11: 0000000000000001 t3 : ff60000001218f00 t4 : ff60000001218f00 [ 17.611041] t5 : ff60000001218000 t6 : ff20000010333988 [ 17.611255] status: 0000000200000020 badaddr: 0000000000000000 cause: 0000000000000008 With the correct PC, the backtrace showed by crash tool as below, crash> bt PID: 113 TASK: ff6000000226c200 CPU: 0 COMMAND: "sh" #0 [ff20000010333b90] riscv_crash_save_regs at ffffffff800078f8 <--- Normal #1 [ff20000010333cf0] panic at ffffffff806578c6 #2 [ff20000010333d50] sysrq_reset_seq_param_set at ffffffff8038c03c #3 [ff20000010333da0] __handle_sysrq at ffffffff8038c604 #4 [ff20000010333e00] write_sysrq_trigger at ffffffff8038cae4 #5 [ff20000010333e20] proc_reg_write at ffffffff801b7ee8 #6 [ff20000010333e40] vfs_write at ffffffff80152bb2 #7 [ff20000010333e80] ksys_write at ffffffff80152eda #8 [ff20000010333ed0] sys_write at ffffffff80152f52 Fixes: e53d281 ("RISC-V: Add kdump support") Co-developed-by: Guo Ren <[email protected]> Signed-off-by: Xianting Tian <[email protected]> Link: https://lore.kernel.org/r/[email protected] Cc: [email protected] Signed-off-by: Palmer Dabbelt <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
anthraxx
pushed a commit
that referenced
this issue
Aug 28, 2022
commit 59c026c upstream. When use 'echo c > /proc/sysrq-trigger' to trigger kdump, riscv_crash_save_regs() will be called to save regs for vmcore, we found "epc" value 00ffffffa5537400 is not a valid kernel virtual address, but is a user virtual address. Other regs(eg, ra, sp, gp...) are correct kernel virtual address. Actually 0x00ffffffb0dd9400 is the user mode PC of 'PID: 113 Comm: sh', which is saved in the task's stack. [ 21.201701] CPU: 0 PID: 113 Comm: sh Kdump: loaded Not tainted 5.18.9 #45 [ 21.201979] Hardware name: riscv-virtio,qemu (DT) [ 21.202160] epc : 00ffffffa5537400 ra : ffffffff80088640 sp : ff20000010333b90 [ 21.202435] gp : ffffffff810dde38 tp : ff6000000226c200 t0 : ffffffff8032be7c [ 21.202707] t1 : 0720072007200720 t2 : 30203a7375746174 s0 : ff20000010333cf0 [ 21.202973] s1 : 0000000000000000 a0 : ff20000010333b98 a1 : 0000000000000001 [ 21.203243] a2 : 0000000000000010 a3 : 0000000000000000 a4 : 28c8f0aeffea4e00 [ 21.203519] a5 : 28c8f0aeffea4e00 a6 : 0000000000000009 a7 : ffffffff8035c9b8 [ 21.203794] s2 : ffffffff810df0a8 s3 : ffffffff810df718 s4 : ff20000010333b98 [ 21.204062] s5 : 0000000000000000 s6 : 0000000000000007 s7 : ffffffff80c4a468 [ 21.204331] s8 : 00ffffffef451410 s9 : 0000000000000007 s10: 00aaaaaac0510700 [ 21.204606] s11: 0000000000000001 t3 : ff60000001218f00 t4 : ff60000001218f00 [ 21.204876] t5 : ff60000001218000 t6 : ff200000103338b8 [ 21.205079] status: 0000000200000020 badaddr: 0000000000000000 cause: 0000000000000008 With the incorrect PC, the backtrace showed by crash tool as below, the first stack frame is abnormal, crash> bt PID: 113 TASK: ff60000002269600 CPU: 0 COMMAND: "sh" #0 [ff2000001039bb90] __efistub_.Ldebug_info0 at 00ffffffa5537400 <-- Abnormal #1 [ff2000001039bcf0] panic at ffffffff806578ba #2 [ff2000001039bd50] sysrq_reset_seq_param_set at ffffffff8038c030 #3 [ff2000001039bda0] __handle_sysrq at ffffffff8038c5f8 #4 [ff2000001039be00] write_sysrq_trigger at ffffffff8038cad8 #5 [ff2000001039be20] proc_reg_write at ffffffff801b7edc #6 [ff2000001039be40] vfs_write at ffffffff80152ba6 #7 [ff2000001039be80] ksys_write at ffffffff80152ece #8 [ff2000001039bed0] sys_write at ffffffff80152f46 With the patch, we can get current kernel mode PC, the output as below, [ 17.607658] CPU: 0 PID: 113 Comm: sh Kdump: loaded Not tainted 5.18.9 #42 [ 17.607937] Hardware name: riscv-virtio,qemu (DT) [ 17.608150] epc : ffffffff800078f8 ra : ffffffff8008862c sp : ff20000010333b90 [ 17.608441] gp : ffffffff810dde38 tp : ff6000000226c200 t0 : ffffffff8032be68 [ 17.608741] t1 : 0720072007200720 t2 : 666666666666663c s0 : ff20000010333cf0 [ 17.609025] s1 : 0000000000000000 a0 : ff20000010333b98 a1 : 0000000000000001 [ 17.609320] a2 : 0000000000000010 a3 : 0000000000000000 a4 : 0000000000000000 [ 17.609601] a5 : ff60000001c78000 a6 : 000000000000003c a7 : ffffffff8035c9a4 [ 17.609894] s2 : ffffffff810df0a8 s3 : ffffffff810df718 s4 : ff20000010333b98 [ 17.610186] s5 : 0000000000000000 s6 : 0000000000000007 s7 : ffffffff80c4a468 [ 17.610469] s8 : 00ffffffca281410 s9 : 0000000000000007 s10: 00aaaaaab5bb6700 [ 17.610755] s11: 0000000000000001 t3 : ff60000001218f00 t4 : ff60000001218f00 [ 17.611041] t5 : ff60000001218000 t6 : ff20000010333988 [ 17.611255] status: 0000000200000020 badaddr: 0000000000000000 cause: 0000000000000008 With the correct PC, the backtrace showed by crash tool as below, crash> bt PID: 113 TASK: ff6000000226c200 CPU: 0 COMMAND: "sh" #0 [ff20000010333b90] riscv_crash_save_regs at ffffffff800078f8 <--- Normal #1 [ff20000010333cf0] panic at ffffffff806578c6 #2 [ff20000010333d50] sysrq_reset_seq_param_set at ffffffff8038c03c #3 [ff20000010333da0] __handle_sysrq at ffffffff8038c604 #4 [ff20000010333e00] write_sysrq_trigger at ffffffff8038cae4 #5 [ff20000010333e20] proc_reg_write at ffffffff801b7ee8 #6 [ff20000010333e40] vfs_write at ffffffff80152bb2 #7 [ff20000010333e80] ksys_write at ffffffff80152eda #8 [ff20000010333ed0] sys_write at ffffffff80152f52 Fixes: e53d281 ("RISC-V: Add kdump support") Co-developed-by: Guo Ren <[email protected]> Signed-off-by: Xianting Tian <[email protected]> Link: https://lore.kernel.org/r/[email protected] Cc: [email protected] Signed-off-by: Palmer Dabbelt <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
anthraxx
pushed a commit
that referenced
this issue
Jan 5, 2023
[ Upstream commit bfcdbae ] This enhances the sanity check for $SDH and $SII while initializing NTFS security, guarantees these index root are legit. [ 162.459513] BUG: KASAN: use-after-free in hdr_find_e.isra.0+0x10c/0x320 [ 162.460176] Read of size 2 at addr ffff8880037bca99 by task mount/243 [ 162.460851] [ 162.461252] CPU: 0 PID: 243 Comm: mount Not tainted 6.0.0-rc7 #42 [ 162.461744] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.14.0-0-g155821a1990b-prebuilt.qemu.org 04/01/2014 [ 162.462609] Call Trace: [ 162.462954] <TASK> [ 162.463276] dump_stack_lvl+0x49/0x63 [ 162.463822] print_report.cold+0xf5/0x689 [ 162.464608] ? unwind_get_return_address+0x3a/0x60 [ 162.465766] ? hdr_find_e.isra.0+0x10c/0x320 [ 162.466975] kasan_report+0xa7/0x130 [ 162.467506] ? _raw_spin_lock_irq+0xc0/0xf0 [ 162.467998] ? hdr_find_e.isra.0+0x10c/0x320 [ 162.468536] __asan_load2+0x68/0x90 [ 162.468923] hdr_find_e.isra.0+0x10c/0x320 [ 162.469282] ? cmp_uints+0xe0/0xe0 [ 162.469557] ? cmp_sdh+0x90/0x90 [ 162.469864] ? ni_find_attr+0x214/0x300 [ 162.470217] ? ni_load_mi+0x80/0x80 [ 162.470479] ? entry_SYSCALL_64_after_hwframe+0x63/0xcd [ 162.470931] ? ntfs_bread_run+0x190/0x190 [ 162.471307] ? indx_get_root+0xe4/0x190 [ 162.471556] ? indx_get_root+0x140/0x190 [ 162.471833] ? indx_init+0x1e0/0x1e0 [ 162.472069] ? fnd_clear+0x115/0x140 [ 162.472363] ? _raw_spin_lock_irqsave+0x100/0x100 [ 162.472731] indx_find+0x184/0x470 [ 162.473461] ? sysvec_apic_timer_interrupt+0x57/0xc0 [ 162.474429] ? indx_find_buffer+0x2d0/0x2d0 [ 162.474704] ? do_syscall_64+0x3b/0x90 [ 162.474962] dir_search_u+0x196/0x2f0 [ 162.475381] ? ntfs_nls_to_utf16+0x450/0x450 [ 162.475661] ? ntfs_security_init+0x3d6/0x440 [ 162.475906] ? is_sd_valid+0x180/0x180 [ 162.476191] ntfs_extend_init+0x13f/0x2c0 [ 162.476496] ? ntfs_fix_post_read+0x130/0x130 [ 162.476861] ? iput.part.0+0x286/0x320 [ 162.477325] ntfs_fill_super+0x11e0/0x1b50 [ 162.477709] ? put_ntfs+0x1d0/0x1d0 [ 162.477970] ? vsprintf+0x20/0x20 [ 162.478258] ? set_blocksize+0x95/0x150 [ 162.478538] get_tree_bdev+0x232/0x370 [ 162.478789] ? put_ntfs+0x1d0/0x1d0 [ 162.479038] ntfs_fs_get_tree+0x15/0x20 [ 162.479374] vfs_get_tree+0x4c/0x130 [ 162.479729] path_mount+0x654/0xfe0 [ 162.480124] ? putname+0x80/0xa0 [ 162.480484] ? finish_automount+0x2e0/0x2e0 [ 162.480894] ? putname+0x80/0xa0 [ 162.481467] ? kmem_cache_free+0x1c4/0x440 [ 162.482280] ? putname+0x80/0xa0 [ 162.482714] do_mount+0xd6/0xf0 [ 162.483264] ? path_mount+0xfe0/0xfe0 [ 162.484782] ? __kasan_check_write+0x14/0x20 [ 162.485593] __x64_sys_mount+0xca/0x110 [ 162.486024] do_syscall_64+0x3b/0x90 [ 162.486543] entry_SYSCALL_64_after_hwframe+0x63/0xcd [ 162.487141] RIP: 0033:0x7f9d374e948a [ 162.488324] Code: 48 8b 0d 11 fa 2a 00 f7 d8 64 89 01 48 83 c8 ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 49 89 ca b8 a5 00 00 008 [ 162.489728] RSP: 002b:00007ffe30e73d18 EFLAGS: 00000206 ORIG_RAX: 00000000000000a5 [ 162.490971] RAX: ffffffffffffffda RBX: 0000561cdb43a060 RCX: 00007f9d374e948a [ 162.491669] RDX: 0000561cdb43a260 RSI: 0000561cdb43a2e0 RDI: 0000561cdb442af0 [ 162.492050] RBP: 0000000000000000 R08: 0000561cdb43a280 R09: 0000000000000020 [ 162.492459] R10: 00000000c0ed0000 R11: 0000000000000206 R12: 0000561cdb442af0 [ 162.493183] R13: 0000561cdb43a260 R14: 0000000000000000 R15: 00000000ffffffff [ 162.493644] </TASK> [ 162.493908] [ 162.494214] The buggy address belongs to the physical page: [ 162.494761] page:000000003e38a3d5 refcount:0 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x37bc [ 162.496064] flags: 0xfffffc0000000(node=0|zone=1|lastcpupid=0x1fffff) [ 162.497278] raw: 000fffffc0000000 ffffea00000df1c8 ffffea00000df008 0000000000000000 [ 162.498928] raw: 0000000000000000 0000000000240000 00000000ffffffff 0000000000000000 [ 162.500542] page dumped because: kasan: bad access detected [ 162.501057] [ 162.501242] Memory state around the buggy address: [ 162.502230] ffff8880037bc980: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 162.502977] ffff8880037bca00: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 162.503522] >ffff8880037bca80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 162.503963] ^ [ 162.504370] ffff8880037bcb00: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 162.504766] ffff8880037bcb80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff Signed-off-by: Edward Lo <[email protected]> Signed-off-by: Konstantin Komarov <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
anthraxx
pushed a commit
that referenced
this issue
Jan 13, 2023
[ Upstream commit bfcdbae ] This enhances the sanity check for $SDH and $SII while initializing NTFS security, guarantees these index root are legit. [ 162.459513] BUG: KASAN: use-after-free in hdr_find_e.isra.0+0x10c/0x320 [ 162.460176] Read of size 2 at addr ffff8880037bca99 by task mount/243 [ 162.460851] [ 162.461252] CPU: 0 PID: 243 Comm: mount Not tainted 6.0.0-rc7 #42 [ 162.461744] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.14.0-0-g155821a1990b-prebuilt.qemu.org 04/01/2014 [ 162.462609] Call Trace: [ 162.462954] <TASK> [ 162.463276] dump_stack_lvl+0x49/0x63 [ 162.463822] print_report.cold+0xf5/0x689 [ 162.464608] ? unwind_get_return_address+0x3a/0x60 [ 162.465766] ? hdr_find_e.isra.0+0x10c/0x320 [ 162.466975] kasan_report+0xa7/0x130 [ 162.467506] ? _raw_spin_lock_irq+0xc0/0xf0 [ 162.467998] ? hdr_find_e.isra.0+0x10c/0x320 [ 162.468536] __asan_load2+0x68/0x90 [ 162.468923] hdr_find_e.isra.0+0x10c/0x320 [ 162.469282] ? cmp_uints+0xe0/0xe0 [ 162.469557] ? cmp_sdh+0x90/0x90 [ 162.469864] ? ni_find_attr+0x214/0x300 [ 162.470217] ? ni_load_mi+0x80/0x80 [ 162.470479] ? entry_SYSCALL_64_after_hwframe+0x63/0xcd [ 162.470931] ? ntfs_bread_run+0x190/0x190 [ 162.471307] ? indx_get_root+0xe4/0x190 [ 162.471556] ? indx_get_root+0x140/0x190 [ 162.471833] ? indx_init+0x1e0/0x1e0 [ 162.472069] ? fnd_clear+0x115/0x140 [ 162.472363] ? _raw_spin_lock_irqsave+0x100/0x100 [ 162.472731] indx_find+0x184/0x470 [ 162.473461] ? sysvec_apic_timer_interrupt+0x57/0xc0 [ 162.474429] ? indx_find_buffer+0x2d0/0x2d0 [ 162.474704] ? do_syscall_64+0x3b/0x90 [ 162.474962] dir_search_u+0x196/0x2f0 [ 162.475381] ? ntfs_nls_to_utf16+0x450/0x450 [ 162.475661] ? ntfs_security_init+0x3d6/0x440 [ 162.475906] ? is_sd_valid+0x180/0x180 [ 162.476191] ntfs_extend_init+0x13f/0x2c0 [ 162.476496] ? ntfs_fix_post_read+0x130/0x130 [ 162.476861] ? iput.part.0+0x286/0x320 [ 162.477325] ntfs_fill_super+0x11e0/0x1b50 [ 162.477709] ? put_ntfs+0x1d0/0x1d0 [ 162.477970] ? vsprintf+0x20/0x20 [ 162.478258] ? set_blocksize+0x95/0x150 [ 162.478538] get_tree_bdev+0x232/0x370 [ 162.478789] ? put_ntfs+0x1d0/0x1d0 [ 162.479038] ntfs_fs_get_tree+0x15/0x20 [ 162.479374] vfs_get_tree+0x4c/0x130 [ 162.479729] path_mount+0x654/0xfe0 [ 162.480124] ? putname+0x80/0xa0 [ 162.480484] ? finish_automount+0x2e0/0x2e0 [ 162.480894] ? putname+0x80/0xa0 [ 162.481467] ? kmem_cache_free+0x1c4/0x440 [ 162.482280] ? putname+0x80/0xa0 [ 162.482714] do_mount+0xd6/0xf0 [ 162.483264] ? path_mount+0xfe0/0xfe0 [ 162.484782] ? __kasan_check_write+0x14/0x20 [ 162.485593] __x64_sys_mount+0xca/0x110 [ 162.486024] do_syscall_64+0x3b/0x90 [ 162.486543] entry_SYSCALL_64_after_hwframe+0x63/0xcd [ 162.487141] RIP: 0033:0x7f9d374e948a [ 162.488324] Code: 48 8b 0d 11 fa 2a 00 f7 d8 64 89 01 48 83 c8 ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 49 89 ca b8 a5 00 00 008 [ 162.489728] RSP: 002b:00007ffe30e73d18 EFLAGS: 00000206 ORIG_RAX: 00000000000000a5 [ 162.490971] RAX: ffffffffffffffda RBX: 0000561cdb43a060 RCX: 00007f9d374e948a [ 162.491669] RDX: 0000561cdb43a260 RSI: 0000561cdb43a2e0 RDI: 0000561cdb442af0 [ 162.492050] RBP: 0000000000000000 R08: 0000561cdb43a280 R09: 0000000000000020 [ 162.492459] R10: 00000000c0ed0000 R11: 0000000000000206 R12: 0000561cdb442af0 [ 162.493183] R13: 0000561cdb43a260 R14: 0000000000000000 R15: 00000000ffffffff [ 162.493644] </TASK> [ 162.493908] [ 162.494214] The buggy address belongs to the physical page: [ 162.494761] page:000000003e38a3d5 refcount:0 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x37bc [ 162.496064] flags: 0xfffffc0000000(node=0|zone=1|lastcpupid=0x1fffff) [ 162.497278] raw: 000fffffc0000000 ffffea00000df1c8 ffffea00000df008 0000000000000000 [ 162.498928] raw: 0000000000000000 0000000000240000 00000000ffffffff 0000000000000000 [ 162.500542] page dumped because: kasan: bad access detected [ 162.501057] [ 162.501242] Memory state around the buggy address: [ 162.502230] ffff8880037bc980: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 162.502977] ffff8880037bca00: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 162.503522] >ffff8880037bca80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 162.503963] ^ [ 162.504370] ffff8880037bcb00: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 162.504766] ffff8880037bcb80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff Signed-off-by: Edward Lo <[email protected]> Signed-off-by: Konstantin Komarov <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
anthraxx
pushed a commit
that referenced
this issue
Jan 14, 2023
[ Upstream commit bfcdbae ] This enhances the sanity check for $SDH and $SII while initializing NTFS security, guarantees these index root are legit. [ 162.459513] BUG: KASAN: use-after-free in hdr_find_e.isra.0+0x10c/0x320 [ 162.460176] Read of size 2 at addr ffff8880037bca99 by task mount/243 [ 162.460851] [ 162.461252] CPU: 0 PID: 243 Comm: mount Not tainted 6.0.0-rc7 #42 [ 162.461744] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.14.0-0-g155821a1990b-prebuilt.qemu.org 04/01/2014 [ 162.462609] Call Trace: [ 162.462954] <TASK> [ 162.463276] dump_stack_lvl+0x49/0x63 [ 162.463822] print_report.cold+0xf5/0x689 [ 162.464608] ? unwind_get_return_address+0x3a/0x60 [ 162.465766] ? hdr_find_e.isra.0+0x10c/0x320 [ 162.466975] kasan_report+0xa7/0x130 [ 162.467506] ? _raw_spin_lock_irq+0xc0/0xf0 [ 162.467998] ? hdr_find_e.isra.0+0x10c/0x320 [ 162.468536] __asan_load2+0x68/0x90 [ 162.468923] hdr_find_e.isra.0+0x10c/0x320 [ 162.469282] ? cmp_uints+0xe0/0xe0 [ 162.469557] ? cmp_sdh+0x90/0x90 [ 162.469864] ? ni_find_attr+0x214/0x300 [ 162.470217] ? ni_load_mi+0x80/0x80 [ 162.470479] ? entry_SYSCALL_64_after_hwframe+0x63/0xcd [ 162.470931] ? ntfs_bread_run+0x190/0x190 [ 162.471307] ? indx_get_root+0xe4/0x190 [ 162.471556] ? indx_get_root+0x140/0x190 [ 162.471833] ? indx_init+0x1e0/0x1e0 [ 162.472069] ? fnd_clear+0x115/0x140 [ 162.472363] ? _raw_spin_lock_irqsave+0x100/0x100 [ 162.472731] indx_find+0x184/0x470 [ 162.473461] ? sysvec_apic_timer_interrupt+0x57/0xc0 [ 162.474429] ? indx_find_buffer+0x2d0/0x2d0 [ 162.474704] ? do_syscall_64+0x3b/0x90 [ 162.474962] dir_search_u+0x196/0x2f0 [ 162.475381] ? ntfs_nls_to_utf16+0x450/0x450 [ 162.475661] ? ntfs_security_init+0x3d6/0x440 [ 162.475906] ? is_sd_valid+0x180/0x180 [ 162.476191] ntfs_extend_init+0x13f/0x2c0 [ 162.476496] ? ntfs_fix_post_read+0x130/0x130 [ 162.476861] ? iput.part.0+0x286/0x320 [ 162.477325] ntfs_fill_super+0x11e0/0x1b50 [ 162.477709] ? put_ntfs+0x1d0/0x1d0 [ 162.477970] ? vsprintf+0x20/0x20 [ 162.478258] ? set_blocksize+0x95/0x150 [ 162.478538] get_tree_bdev+0x232/0x370 [ 162.478789] ? put_ntfs+0x1d0/0x1d0 [ 162.479038] ntfs_fs_get_tree+0x15/0x20 [ 162.479374] vfs_get_tree+0x4c/0x130 [ 162.479729] path_mount+0x654/0xfe0 [ 162.480124] ? putname+0x80/0xa0 [ 162.480484] ? finish_automount+0x2e0/0x2e0 [ 162.480894] ? putname+0x80/0xa0 [ 162.481467] ? kmem_cache_free+0x1c4/0x440 [ 162.482280] ? putname+0x80/0xa0 [ 162.482714] do_mount+0xd6/0xf0 [ 162.483264] ? path_mount+0xfe0/0xfe0 [ 162.484782] ? __kasan_check_write+0x14/0x20 [ 162.485593] __x64_sys_mount+0xca/0x110 [ 162.486024] do_syscall_64+0x3b/0x90 [ 162.486543] entry_SYSCALL_64_after_hwframe+0x63/0xcd [ 162.487141] RIP: 0033:0x7f9d374e948a [ 162.488324] Code: 48 8b 0d 11 fa 2a 00 f7 d8 64 89 01 48 83 c8 ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 49 89 ca b8 a5 00 00 008 [ 162.489728] RSP: 002b:00007ffe30e73d18 EFLAGS: 00000206 ORIG_RAX: 00000000000000a5 [ 162.490971] RAX: ffffffffffffffda RBX: 0000561cdb43a060 RCX: 00007f9d374e948a [ 162.491669] RDX: 0000561cdb43a260 RSI: 0000561cdb43a2e0 RDI: 0000561cdb442af0 [ 162.492050] RBP: 0000000000000000 R08: 0000561cdb43a280 R09: 0000000000000020 [ 162.492459] R10: 00000000c0ed0000 R11: 0000000000000206 R12: 0000561cdb442af0 [ 162.493183] R13: 0000561cdb43a260 R14: 0000000000000000 R15: 00000000ffffffff [ 162.493644] </TASK> [ 162.493908] [ 162.494214] The buggy address belongs to the physical page: [ 162.494761] page:000000003e38a3d5 refcount:0 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x37bc [ 162.496064] flags: 0xfffffc0000000(node=0|zone=1|lastcpupid=0x1fffff) [ 162.497278] raw: 000fffffc0000000 ffffea00000df1c8 ffffea00000df008 0000000000000000 [ 162.498928] raw: 0000000000000000 0000000000240000 00000000ffffffff 0000000000000000 [ 162.500542] page dumped because: kasan: bad access detected [ 162.501057] [ 162.501242] Memory state around the buggy address: [ 162.502230] ffff8880037bc980: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 162.502977] ffff8880037bca00: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 162.503522] >ffff8880037bca80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 162.503963] ^ [ 162.504370] ffff8880037bcb00: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 162.504766] ffff8880037bcb80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff Signed-off-by: Edward Lo <[email protected]> Signed-off-by: Konstantin Komarov <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
hardfalcon
pushed a commit
to hardfalcon/linux-hardened
that referenced
this issue
May 26, 2023
[ Upstream commit 08e8cf5 ] This adds a length check to guarantee the retrieved index root is legit. [ 162.459513] BUG: KASAN: use-after-free in hdr_find_e.isra.0+0x10c/0x320 [ 162.460176] Read of size 2 at addr ffff8880037bca99 by task mount/243 [ 162.460851] [ 162.461252] CPU: 0 PID: 243 Comm: mount Not tainted 6.0.0-rc7 anthraxx#42 [ 162.461744] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.14.0-0-g155821a1990b-prebuilt.qemu.org 04/01/2014 [ 162.462609] Call Trace: [ 162.462954] <TASK> [ 162.463276] dump_stack_lvl+0x49/0x63 [ 162.463822] print_report.cold+0xf5/0x689 [ 162.464608] ? unwind_get_return_address+0x3a/0x60 [ 162.465766] ? hdr_find_e.isra.0+0x10c/0x320 [ 162.466975] kasan_report+0xa7/0x130 [ 162.467506] ? _raw_spin_lock_irq+0xc0/0xf0 [ 162.467998] ? hdr_find_e.isra.0+0x10c/0x320 [ 162.468536] __asan_load2+0x68/0x90 [ 162.468923] hdr_find_e.isra.0+0x10c/0x320 [ 162.469282] ? cmp_uints+0xe0/0xe0 [ 162.469557] ? cmp_sdh+0x90/0x90 [ 162.469864] ? ni_find_attr+0x214/0x300 [ 162.470217] ? ni_load_mi+0x80/0x80 [ 162.470479] ? entry_SYSCALL_64_after_hwframe+0x63/0xcd [ 162.470931] ? ntfs_bread_run+0x190/0x190 [ 162.471307] ? indx_get_root+0xe4/0x190 [ 162.471556] ? indx_get_root+0x140/0x190 [ 162.471833] ? indx_init+0x1e0/0x1e0 [ 162.472069] ? fnd_clear+0x115/0x140 [ 162.472363] ? _raw_spin_lock_irqsave+0x100/0x100 [ 162.472731] indx_find+0x184/0x470 [ 162.473461] ? sysvec_apic_timer_interrupt+0x57/0xc0 [ 162.474429] ? indx_find_buffer+0x2d0/0x2d0 [ 162.474704] ? do_syscall_64+0x3b/0x90 [ 162.474962] dir_search_u+0x196/0x2f0 [ 162.475381] ? ntfs_nls_to_utf16+0x450/0x450 [ 162.475661] ? ntfs_security_init+0x3d6/0x440 [ 162.475906] ? is_sd_valid+0x180/0x180 [ 162.476191] ntfs_extend_init+0x13f/0x2c0 [ 162.476496] ? ntfs_fix_post_read+0x130/0x130 [ 162.476861] ? iput.part.0+0x286/0x320 [ 162.477325] ntfs_fill_super+0x11e0/0x1b50 [ 162.477709] ? put_ntfs+0x1d0/0x1d0 [ 162.477970] ? vsprintf+0x20/0x20 [ 162.478258] ? set_blocksize+0x95/0x150 [ 162.478538] get_tree_bdev+0x232/0x370 [ 162.478789] ? put_ntfs+0x1d0/0x1d0 [ 162.479038] ntfs_fs_get_tree+0x15/0x20 [ 162.479374] vfs_get_tree+0x4c/0x130 [ 162.479729] path_mount+0x654/0xfe0 [ 162.480124] ? putname+0x80/0xa0 [ 162.480484] ? finish_automount+0x2e0/0x2e0 [ 162.480894] ? putname+0x80/0xa0 [ 162.481467] ? kmem_cache_free+0x1c4/0x440 [ 162.482280] ? putname+0x80/0xa0 [ 162.482714] do_mount+0xd6/0xf0 [ 162.483264] ? path_mount+0xfe0/0xfe0 [ 162.484782] ? __kasan_check_write+0x14/0x20 [ 162.485593] __x64_sys_mount+0xca/0x110 [ 162.486024] do_syscall_64+0x3b/0x90 [ 162.486543] entry_SYSCALL_64_after_hwframe+0x63/0xcd [ 162.487141] RIP: 0033:0x7f9d374e948a [ 162.488324] Code: 48 8b 0d 11 fa 2a 00 f7 d8 64 89 01 48 83 c8 ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 49 89 ca b8 a5 00 00 008 [ 162.489728] RSP: 002b:00007ffe30e73d18 EFLAGS: 00000206 ORIG_RAX: 00000000000000a5 [ 162.490971] RAX: ffffffffffffffda RBX: 0000561cdb43a060 RCX: 00007f9d374e948a [ 162.491669] RDX: 0000561cdb43a260 RSI: 0000561cdb43a2e0 RDI: 0000561cdb442af0 [ 162.492050] RBP: 0000000000000000 R08: 0000561cdb43a280 R09: 0000000000000020 [ 162.492459] R10: 00000000c0ed0000 R11: 0000000000000206 R12: 0000561cdb442af0 [ 162.493183] R13: 0000561cdb43a260 R14: 0000000000000000 R15: 00000000ffffffff [ 162.493644] </TASK> [ 162.493908] [ 162.494214] The buggy address belongs to the physical page: [ 162.494761] page:000000003e38a3d5 refcount:0 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x37bc [ 162.496064] flags: 0xfffffc0000000(node=0|zone=1|lastcpupid=0x1fffff) [ 162.497278] raw: 000fffffc0000000 ffffea00000df1c8 ffffea00000df008 0000000000000000 [ 162.498928] raw: 0000000000000000 0000000000240000 00000000ffffffff 0000000000000000 [ 162.500542] page dumped because: kasan: bad access detected [ 162.501057] [ 162.501242] Memory state around the buggy address: [ 162.502230] ffff8880037bc980: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 162.502977] ffff8880037bca00: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 162.503522] >ffff8880037bca80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 162.503963] ^ [ 162.504370] ffff8880037bcb00: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 162.504766] ffff8880037bcb80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff Signed-off-by: Edward Lo <[email protected]> Signed-off-by: Konstantin Komarov <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
anthraxx
pushed a commit
that referenced
this issue
Jun 1, 2023
[ Upstream commit 08e8cf5 ] This adds a length check to guarantee the retrieved index root is legit. [ 162.459513] BUG: KASAN: use-after-free in hdr_find_e.isra.0+0x10c/0x320 [ 162.460176] Read of size 2 at addr ffff8880037bca99 by task mount/243 [ 162.460851] [ 162.461252] CPU: 0 PID: 243 Comm: mount Not tainted 6.0.0-rc7 #42 [ 162.461744] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.14.0-0-g155821a1990b-prebuilt.qemu.org 04/01/2014 [ 162.462609] Call Trace: [ 162.462954] <TASK> [ 162.463276] dump_stack_lvl+0x49/0x63 [ 162.463822] print_report.cold+0xf5/0x689 [ 162.464608] ? unwind_get_return_address+0x3a/0x60 [ 162.465766] ? hdr_find_e.isra.0+0x10c/0x320 [ 162.466975] kasan_report+0xa7/0x130 [ 162.467506] ? _raw_spin_lock_irq+0xc0/0xf0 [ 162.467998] ? hdr_find_e.isra.0+0x10c/0x320 [ 162.468536] __asan_load2+0x68/0x90 [ 162.468923] hdr_find_e.isra.0+0x10c/0x320 [ 162.469282] ? cmp_uints+0xe0/0xe0 [ 162.469557] ? cmp_sdh+0x90/0x90 [ 162.469864] ? ni_find_attr+0x214/0x300 [ 162.470217] ? ni_load_mi+0x80/0x80 [ 162.470479] ? entry_SYSCALL_64_after_hwframe+0x63/0xcd [ 162.470931] ? ntfs_bread_run+0x190/0x190 [ 162.471307] ? indx_get_root+0xe4/0x190 [ 162.471556] ? indx_get_root+0x140/0x190 [ 162.471833] ? indx_init+0x1e0/0x1e0 [ 162.472069] ? fnd_clear+0x115/0x140 [ 162.472363] ? _raw_spin_lock_irqsave+0x100/0x100 [ 162.472731] indx_find+0x184/0x470 [ 162.473461] ? sysvec_apic_timer_interrupt+0x57/0xc0 [ 162.474429] ? indx_find_buffer+0x2d0/0x2d0 [ 162.474704] ? do_syscall_64+0x3b/0x90 [ 162.474962] dir_search_u+0x196/0x2f0 [ 162.475381] ? ntfs_nls_to_utf16+0x450/0x450 [ 162.475661] ? ntfs_security_init+0x3d6/0x440 [ 162.475906] ? is_sd_valid+0x180/0x180 [ 162.476191] ntfs_extend_init+0x13f/0x2c0 [ 162.476496] ? ntfs_fix_post_read+0x130/0x130 [ 162.476861] ? iput.part.0+0x286/0x320 [ 162.477325] ntfs_fill_super+0x11e0/0x1b50 [ 162.477709] ? put_ntfs+0x1d0/0x1d0 [ 162.477970] ? vsprintf+0x20/0x20 [ 162.478258] ? set_blocksize+0x95/0x150 [ 162.478538] get_tree_bdev+0x232/0x370 [ 162.478789] ? put_ntfs+0x1d0/0x1d0 [ 162.479038] ntfs_fs_get_tree+0x15/0x20 [ 162.479374] vfs_get_tree+0x4c/0x130 [ 162.479729] path_mount+0x654/0xfe0 [ 162.480124] ? putname+0x80/0xa0 [ 162.480484] ? finish_automount+0x2e0/0x2e0 [ 162.480894] ? putname+0x80/0xa0 [ 162.481467] ? kmem_cache_free+0x1c4/0x440 [ 162.482280] ? putname+0x80/0xa0 [ 162.482714] do_mount+0xd6/0xf0 [ 162.483264] ? path_mount+0xfe0/0xfe0 [ 162.484782] ? __kasan_check_write+0x14/0x20 [ 162.485593] __x64_sys_mount+0xca/0x110 [ 162.486024] do_syscall_64+0x3b/0x90 [ 162.486543] entry_SYSCALL_64_after_hwframe+0x63/0xcd [ 162.487141] RIP: 0033:0x7f9d374e948a [ 162.488324] Code: 48 8b 0d 11 fa 2a 00 f7 d8 64 89 01 48 83 c8 ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 49 89 ca b8 a5 00 00 008 [ 162.489728] RSP: 002b:00007ffe30e73d18 EFLAGS: 00000206 ORIG_RAX: 00000000000000a5 [ 162.490971] RAX: ffffffffffffffda RBX: 0000561cdb43a060 RCX: 00007f9d374e948a [ 162.491669] RDX: 0000561cdb43a260 RSI: 0000561cdb43a2e0 RDI: 0000561cdb442af0 [ 162.492050] RBP: 0000000000000000 R08: 0000561cdb43a280 R09: 0000000000000020 [ 162.492459] R10: 00000000c0ed0000 R11: 0000000000000206 R12: 0000561cdb442af0 [ 162.493183] R13: 0000561cdb43a260 R14: 0000000000000000 R15: 00000000ffffffff [ 162.493644] </TASK> [ 162.493908] [ 162.494214] The buggy address belongs to the physical page: [ 162.494761] page:000000003e38a3d5 refcount:0 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x37bc [ 162.496064] flags: 0xfffffc0000000(node=0|zone=1|lastcpupid=0x1fffff) [ 162.497278] raw: 000fffffc0000000 ffffea00000df1c8 ffffea00000df008 0000000000000000 [ 162.498928] raw: 0000000000000000 0000000000240000 00000000ffffffff 0000000000000000 [ 162.500542] page dumped because: kasan: bad access detected [ 162.501057] [ 162.501242] Memory state around the buggy address: [ 162.502230] ffff8880037bc980: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 162.502977] ffff8880037bca00: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 162.503522] >ffff8880037bca80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 162.503963] ^ [ 162.504370] ffff8880037bcb00: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 162.504766] ffff8880037bcb80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff Signed-off-by: Edward Lo <[email protected]> Signed-off-by: Konstantin Komarov <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
anthraxx
pushed a commit
that referenced
this issue
Jun 1, 2023
commit 3511227 upstream. We found a crash when using SMCRv2 with 2 Mellanox ConnectX-4. It can be reproduced by: - smc_run nginx - smc_run wrk -t 32 -c 500 -d 30 http://<ip>:<port> BUG: kernel NULL pointer dereference, address: 0000000000000014 #PF: supervisor read access in kernel mode #PF: error_code(0x0000) - not-present page PGD 8000000108713067 P4D 8000000108713067 PUD 151127067 PMD 0 Oops: 0000 [#1] PREEMPT SMP PTI CPU: 4 PID: 2441 Comm: kworker/4:249 Kdump: loaded Tainted: G W E 6.4.0-rc1+ #42 Workqueue: smc_hs_wq smc_listen_work [smc] RIP: 0010:smc_clc_send_confirm_accept+0x284/0x580 [smc] RSP: 0018:ffffb8294b2d7c78 EFLAGS: 00010a06 RAX: ffff8f1873238880 RBX: ffffb8294b2d7dc8 RCX: 0000000000000000 RDX: 00000000000000b4 RSI: 0000000000000001 RDI: 0000000000b40c00 RBP: ffffb8294b2d7db8 R08: ffff8f1815c5860c R09: 0000000000000000 R10: 0000000000000400 R11: 0000000000000000 R12: ffff8f1846f56180 R13: ffff8f1815c5860c R14: 0000000000000001 R15: 0000000000000001 FS: 0000000000000000(0000) GS:ffff8f1aefd00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000014 CR3: 00000001027a0001 CR4: 00000000003706e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> ? mlx5_ib_map_mr_sg+0xa1/0xd0 [mlx5_ib] ? smcr_buf_map_link+0x24b/0x290 [smc] ? __smc_buf_create+0x4ee/0x9b0 [smc] smc_clc_send_accept+0x4c/0xb0 [smc] smc_listen_work+0x346/0x650 [smc] ? __schedule+0x279/0x820 process_one_work+0x1e5/0x3f0 worker_thread+0x4d/0x2f0 ? __pfx_worker_thread+0x10/0x10 kthread+0xe5/0x120 ? __pfx_kthread+0x10/0x10 ret_from_fork+0x2c/0x50 </TASK> During the CLC handshake, server sequentially tries available SMCRv2 and SMCRv1 devices in smc_listen_work(). If an SMCRv2 device is found. SMCv2 based link group and link will be assigned to the connection. Then assumed that some buffer assignment errors happen later in the CLC handshake, such as RMB registration failure, server will give up SMCRv2 and try SMCRv1 device instead. But the resources assigned to the connection won't be reset. When server tries SMCRv1 device, the connection creation process will be executed again. Since conn->lnk has been assigned when trying SMCRv2, it will not be set to the correct SMCRv1 link in smcr_lgr_conn_assign_link(). So in such situation, conn->lgr points to correct SMCRv1 link group but conn->lnk points to the SMCRv2 link mistakenly. Then in smc_clc_send_confirm_accept(), conn->rmb_desc->mr[link->link_idx] will be accessed. Since the link->link_idx is not correct, the related MR may not have been initialized, so crash happens. | Try SMCRv2 device first | |-> conn->lgr: assign existed SMCRv2 link group; | |-> conn->link: assign existed SMCRv2 link (link_idx may be 1 in SMC_LGR_SYMMETRIC); | |-> sndbuf & RMB creation fails, quit; | | Try SMCRv1 device then | |-> conn->lgr: create SMCRv1 link group and assign; | |-> conn->link: keep SMCRv2 link mistakenly; | |-> sndbuf & RMB creation succeed, only RMB->mr[link_idx = 0] | initialized. | | Then smc_clc_send_confirm_accept() accesses | conn->rmb_desc->mr[conn->link->link_idx, which is 1], then crash. v This patch tries to fix this by cleaning conn->lnk before assigning link. In addition, it is better to reset the connection and clean the resources assigned if trying SMCRv2 failed in buffer creation or registration. Fixes: e49300a ("net/smc: add listen processing for SMC-Rv2") Link: https://lore.kernel.org/r/[email protected]/ Signed-off-by: Wen Gu <[email protected]> Reviewed-by: Tony Lu <[email protected]> Signed-off-by: David S. Miller <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
anthraxx
pushed a commit
that referenced
this issue
Jun 27, 2023
commit 3511227 upstream. We found a crash when using SMCRv2 with 2 Mellanox ConnectX-4. It can be reproduced by: - smc_run nginx - smc_run wrk -t 32 -c 500 -d 30 http://<ip>:<port> BUG: kernel NULL pointer dereference, address: 0000000000000014 #PF: supervisor read access in kernel mode #PF: error_code(0x0000) - not-present page PGD 8000000108713067 P4D 8000000108713067 PUD 151127067 PMD 0 Oops: 0000 [#1] PREEMPT SMP PTI CPU: 4 PID: 2441 Comm: kworker/4:249 Kdump: loaded Tainted: G W E 6.4.0-rc1+ #42 Workqueue: smc_hs_wq smc_listen_work [smc] RIP: 0010:smc_clc_send_confirm_accept+0x284/0x580 [smc] RSP: 0018:ffffb8294b2d7c78 EFLAGS: 00010a06 RAX: ffff8f1873238880 RBX: ffffb8294b2d7dc8 RCX: 0000000000000000 RDX: 00000000000000b4 RSI: 0000000000000001 RDI: 0000000000b40c00 RBP: ffffb8294b2d7db8 R08: ffff8f1815c5860c R09: 0000000000000000 R10: 0000000000000400 R11: 0000000000000000 R12: ffff8f1846f56180 R13: ffff8f1815c5860c R14: 0000000000000001 R15: 0000000000000001 FS: 0000000000000000(0000) GS:ffff8f1aefd00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000014 CR3: 00000001027a0001 CR4: 00000000003706e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> ? mlx5_ib_map_mr_sg+0xa1/0xd0 [mlx5_ib] ? smcr_buf_map_link+0x24b/0x290 [smc] ? __smc_buf_create+0x4ee/0x9b0 [smc] smc_clc_send_accept+0x4c/0xb0 [smc] smc_listen_work+0x346/0x650 [smc] ? __schedule+0x279/0x820 process_one_work+0x1e5/0x3f0 worker_thread+0x4d/0x2f0 ? __pfx_worker_thread+0x10/0x10 kthread+0xe5/0x120 ? __pfx_kthread+0x10/0x10 ret_from_fork+0x2c/0x50 </TASK> During the CLC handshake, server sequentially tries available SMCRv2 and SMCRv1 devices in smc_listen_work(). If an SMCRv2 device is found. SMCv2 based link group and link will be assigned to the connection. Then assumed that some buffer assignment errors happen later in the CLC handshake, such as RMB registration failure, server will give up SMCRv2 and try SMCRv1 device instead. But the resources assigned to the connection won't be reset. When server tries SMCRv1 device, the connection creation process will be executed again. Since conn->lnk has been assigned when trying SMCRv2, it will not be set to the correct SMCRv1 link in smcr_lgr_conn_assign_link(). So in such situation, conn->lgr points to correct SMCRv1 link group but conn->lnk points to the SMCRv2 link mistakenly. Then in smc_clc_send_confirm_accept(), conn->rmb_desc->mr[link->link_idx] will be accessed. Since the link->link_idx is not correct, the related MR may not have been initialized, so crash happens. | Try SMCRv2 device first | |-> conn->lgr: assign existed SMCRv2 link group; | |-> conn->link: assign existed SMCRv2 link (link_idx may be 1 in SMC_LGR_SYMMETRIC); | |-> sndbuf & RMB creation fails, quit; | | Try SMCRv1 device then | |-> conn->lgr: create SMCRv1 link group and assign; | |-> conn->link: keep SMCRv2 link mistakenly; | |-> sndbuf & RMB creation succeed, only RMB->mr[link_idx = 0] | initialized. | | Then smc_clc_send_confirm_accept() accesses | conn->rmb_desc->mr[conn->link->link_idx, which is 1], then crash. v This patch tries to fix this by cleaning conn->lnk before assigning link. In addition, it is better to reset the connection and clean the resources assigned if trying SMCRv2 failed in buffer creation or registration. Fixes: e49300a ("net/smc: add listen processing for SMC-Rv2") Link: https://lore.kernel.org/r/[email protected]/ Signed-off-by: Wen Gu <[email protected]> Reviewed-by: Tony Lu <[email protected]> Signed-off-by: David S. Miller <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
anthraxx
pushed a commit
that referenced
this issue
Mar 6, 2024
[ Upstream commit 08e8cf5 ] This adds a length check to guarantee the retrieved index root is legit. [ 162.459513] BUG: KASAN: use-after-free in hdr_find_e.isra.0+0x10c/0x320 [ 162.460176] Read of size 2 at addr ffff8880037bca99 by task mount/243 [ 162.460851] [ 162.461252] CPU: 0 PID: 243 Comm: mount Not tainted 6.0.0-rc7 #42 [ 162.461744] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.14.0-0-g155821a1990b-prebuilt.qemu.org 04/01/2014 [ 162.462609] Call Trace: [ 162.462954] <TASK> [ 162.463276] dump_stack_lvl+0x49/0x63 [ 162.463822] print_report.cold+0xf5/0x689 [ 162.464608] ? unwind_get_return_address+0x3a/0x60 [ 162.465766] ? hdr_find_e.isra.0+0x10c/0x320 [ 162.466975] kasan_report+0xa7/0x130 [ 162.467506] ? _raw_spin_lock_irq+0xc0/0xf0 [ 162.467998] ? hdr_find_e.isra.0+0x10c/0x320 [ 162.468536] __asan_load2+0x68/0x90 [ 162.468923] hdr_find_e.isra.0+0x10c/0x320 [ 162.469282] ? cmp_uints+0xe0/0xe0 [ 162.469557] ? cmp_sdh+0x90/0x90 [ 162.469864] ? ni_find_attr+0x214/0x300 [ 162.470217] ? ni_load_mi+0x80/0x80 [ 162.470479] ? entry_SYSCALL_64_after_hwframe+0x63/0xcd [ 162.470931] ? ntfs_bread_run+0x190/0x190 [ 162.471307] ? indx_get_root+0xe4/0x190 [ 162.471556] ? indx_get_root+0x140/0x190 [ 162.471833] ? indx_init+0x1e0/0x1e0 [ 162.472069] ? fnd_clear+0x115/0x140 [ 162.472363] ? _raw_spin_lock_irqsave+0x100/0x100 [ 162.472731] indx_find+0x184/0x470 [ 162.473461] ? sysvec_apic_timer_interrupt+0x57/0xc0 [ 162.474429] ? indx_find_buffer+0x2d0/0x2d0 [ 162.474704] ? do_syscall_64+0x3b/0x90 [ 162.474962] dir_search_u+0x196/0x2f0 [ 162.475381] ? ntfs_nls_to_utf16+0x450/0x450 [ 162.475661] ? ntfs_security_init+0x3d6/0x440 [ 162.475906] ? is_sd_valid+0x180/0x180 [ 162.476191] ntfs_extend_init+0x13f/0x2c0 [ 162.476496] ? ntfs_fix_post_read+0x130/0x130 [ 162.476861] ? iput.part.0+0x286/0x320 [ 162.477325] ntfs_fill_super+0x11e0/0x1b50 [ 162.477709] ? put_ntfs+0x1d0/0x1d0 [ 162.477970] ? vsprintf+0x20/0x20 [ 162.478258] ? set_blocksize+0x95/0x150 [ 162.478538] get_tree_bdev+0x232/0x370 [ 162.478789] ? put_ntfs+0x1d0/0x1d0 [ 162.479038] ntfs_fs_get_tree+0x15/0x20 [ 162.479374] vfs_get_tree+0x4c/0x130 [ 162.479729] path_mount+0x654/0xfe0 [ 162.480124] ? putname+0x80/0xa0 [ 162.480484] ? finish_automount+0x2e0/0x2e0 [ 162.480894] ? putname+0x80/0xa0 [ 162.481467] ? kmem_cache_free+0x1c4/0x440 [ 162.482280] ? putname+0x80/0xa0 [ 162.482714] do_mount+0xd6/0xf0 [ 162.483264] ? path_mount+0xfe0/0xfe0 [ 162.484782] ? __kasan_check_write+0x14/0x20 [ 162.485593] __x64_sys_mount+0xca/0x110 [ 162.486024] do_syscall_64+0x3b/0x90 [ 162.486543] entry_SYSCALL_64_after_hwframe+0x63/0xcd [ 162.487141] RIP: 0033:0x7f9d374e948a [ 162.488324] Code: 48 8b 0d 11 fa 2a 00 f7 d8 64 89 01 48 83 c8 ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 49 89 ca b8 a5 00 00 008 [ 162.489728] RSP: 002b:00007ffe30e73d18 EFLAGS: 00000206 ORIG_RAX: 00000000000000a5 [ 162.490971] RAX: ffffffffffffffda RBX: 0000561cdb43a060 RCX: 00007f9d374e948a [ 162.491669] RDX: 0000561cdb43a260 RSI: 0000561cdb43a2e0 RDI: 0000561cdb442af0 [ 162.492050] RBP: 0000000000000000 R08: 0000561cdb43a280 R09: 0000000000000020 [ 162.492459] R10: 00000000c0ed0000 R11: 0000000000000206 R12: 0000561cdb442af0 [ 162.493183] R13: 0000561cdb43a260 R14: 0000000000000000 R15: 00000000ffffffff [ 162.493644] </TASK> [ 162.493908] [ 162.494214] The buggy address belongs to the physical page: [ 162.494761] page:000000003e38a3d5 refcount:0 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x37bc [ 162.496064] flags: 0xfffffc0000000(node=0|zone=1|lastcpupid=0x1fffff) [ 162.497278] raw: 000fffffc0000000 ffffea00000df1c8 ffffea00000df008 0000000000000000 [ 162.498928] raw: 0000000000000000 0000000000240000 00000000ffffffff 0000000000000000 [ 162.500542] page dumped because: kasan: bad access detected [ 162.501057] [ 162.501242] Memory state around the buggy address: [ 162.502230] ffff8880037bc980: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 162.502977] ffff8880037bca00: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 162.503522] >ffff8880037bca80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 162.503963] ^ [ 162.504370] ffff8880037bcb00: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 162.504766] ffff8880037bcb80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff Signed-off-by: Edward Lo <[email protected]> Signed-off-by: Konstantin Komarov <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
anthraxx
pushed a commit
that referenced
this issue
Aug 7, 2024
[ Upstream commit 97d833c ] ACLs in Spectrum-2 and newer ASICs can reside in the algorithmic TCAM (A-TCAM) or in the ordinary circuit TCAM (C-TCAM). The former can contain more ACLs (i.e., tc filters), but the number of masks in each region (i.e., tc chain) is limited. In order to mitigate the effects of the above limitation, the device allows filters to share a single mask if their masks only differ in up to 8 consecutive bits. For example, dst_ip/25 can be represented using dst_ip/24 with a delta of 1 bit. The C-TCAM does not have a limit on the number of masks being used (and therefore does not support mask aggregation), but can contain a limited number of filters. The driver uses the "objagg" library to perform the mask aggregation by passing it objects that consist of the filter's mask and whether the filter is to be inserted into the A-TCAM or the C-TCAM since filters in different TCAMs cannot share a mask. The set of created objects is dependent on the insertion order of the filters and is not necessarily optimal. Therefore, the driver will periodically ask the library to compute a more optimal set ("hints") by looking at all the existing objects. When the library asks the driver whether two objects can be aggregated the driver only compares the provided masks and ignores the A-TCAM / C-TCAM indication. This is the right thing to do since the goal is to move as many filters as possible to the A-TCAM. The driver also forbids two identical masks from being aggregated since this can only happen if one was intentionally put in the C-TCAM to avoid a conflict in the A-TCAM. The above can result in the following set of hints: H1: {mask X, A-TCAM} -> H2: {mask Y, A-TCAM} // X is Y + delta H3: {mask Y, C-TCAM} -> H4: {mask Z, A-TCAM} // Y is Z + delta After getting the hints from the library the driver will start migrating filters from one region to another while consulting the computed hints and instructing the device to perform a lookup in both regions during the transition. Assuming a filter with mask X is being migrated into the A-TCAM in the new region, the hints lookup will return H1. Since H2 is the parent of H1, the library will try to find the object associated with it and create it if necessary in which case another hints lookup (recursive) will be performed. This hints lookup for {mask Y, A-TCAM} will either return H2 or H3 since the driver passes the library an object comparison function that ignores the A-TCAM / C-TCAM indication. This can eventually lead to nested objects which are not supported by the library [1]. Fix by removing the object comparison function from both the driver and the library as the driver was the only user. That way the lookup will only return exact matches. I do not have a reliable reproducer that can reproduce the issue in a timely manner, but before the fix the issue would reproduce in several minutes and with the fix it does not reproduce in over an hour. Note that the current usefulness of the hints is limited because they include the C-TCAM indication and represent aggregation that cannot actually happen. This will be addressed in net-next. [1] WARNING: CPU: 0 PID: 153 at lib/objagg.c:170 objagg_obj_parent_assign+0xb5/0xd0 Modules linked in: CPU: 0 PID: 153 Comm: kworker/0:18 Not tainted 6.9.0-rc6-custom-g70fbc2c1c38b #42 Hardware name: Mellanox Technologies Ltd. MSN3700C/VMOD0008, BIOS 5.11 10/10/2018 Workqueue: mlxsw_core mlxsw_sp_acl_tcam_vregion_rehash_work RIP: 0010:objagg_obj_parent_assign+0xb5/0xd0 [...] Call Trace: <TASK> __objagg_obj_get+0x2bb/0x580 objagg_obj_get+0xe/0x80 mlxsw_sp_acl_erp_mask_get+0xb5/0xf0 mlxsw_sp_acl_atcam_entry_add+0xe8/0x3c0 mlxsw_sp_acl_tcam_entry_create+0x5e/0xa0 mlxsw_sp_acl_tcam_vchunk_migrate_one+0x16b/0x270 mlxsw_sp_acl_tcam_vregion_rehash_work+0xbe/0x510 process_one_work+0x151/0x370 Fixes: 9069a38 ("lib: objagg: implement optimization hints assembly and use hints for object creation") Signed-off-by: Ido Schimmel <[email protected]> Reviewed-by: Amit Cohen <[email protected]> Tested-by: Alexander Zubkov <[email protected]> Signed-off-by: Petr Machata <[email protected]> Reviewed-by: Simon Horman <[email protected]> Signed-off-by: David S. Miller <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
anthraxx
pushed a commit
that referenced
this issue
Aug 7, 2024
[ Upstream commit 97d833c ] ACLs in Spectrum-2 and newer ASICs can reside in the algorithmic TCAM (A-TCAM) or in the ordinary circuit TCAM (C-TCAM). The former can contain more ACLs (i.e., tc filters), but the number of masks in each region (i.e., tc chain) is limited. In order to mitigate the effects of the above limitation, the device allows filters to share a single mask if their masks only differ in up to 8 consecutive bits. For example, dst_ip/25 can be represented using dst_ip/24 with a delta of 1 bit. The C-TCAM does not have a limit on the number of masks being used (and therefore does not support mask aggregation), but can contain a limited number of filters. The driver uses the "objagg" library to perform the mask aggregation by passing it objects that consist of the filter's mask and whether the filter is to be inserted into the A-TCAM or the C-TCAM since filters in different TCAMs cannot share a mask. The set of created objects is dependent on the insertion order of the filters and is not necessarily optimal. Therefore, the driver will periodically ask the library to compute a more optimal set ("hints") by looking at all the existing objects. When the library asks the driver whether two objects can be aggregated the driver only compares the provided masks and ignores the A-TCAM / C-TCAM indication. This is the right thing to do since the goal is to move as many filters as possible to the A-TCAM. The driver also forbids two identical masks from being aggregated since this can only happen if one was intentionally put in the C-TCAM to avoid a conflict in the A-TCAM. The above can result in the following set of hints: H1: {mask X, A-TCAM} -> H2: {mask Y, A-TCAM} // X is Y + delta H3: {mask Y, C-TCAM} -> H4: {mask Z, A-TCAM} // Y is Z + delta After getting the hints from the library the driver will start migrating filters from one region to another while consulting the computed hints and instructing the device to perform a lookup in both regions during the transition. Assuming a filter with mask X is being migrated into the A-TCAM in the new region, the hints lookup will return H1. Since H2 is the parent of H1, the library will try to find the object associated with it and create it if necessary in which case another hints lookup (recursive) will be performed. This hints lookup for {mask Y, A-TCAM} will either return H2 or H3 since the driver passes the library an object comparison function that ignores the A-TCAM / C-TCAM indication. This can eventually lead to nested objects which are not supported by the library [1]. Fix by removing the object comparison function from both the driver and the library as the driver was the only user. That way the lookup will only return exact matches. I do not have a reliable reproducer that can reproduce the issue in a timely manner, but before the fix the issue would reproduce in several minutes and with the fix it does not reproduce in over an hour. Note that the current usefulness of the hints is limited because they include the C-TCAM indication and represent aggregation that cannot actually happen. This will be addressed in net-next. [1] WARNING: CPU: 0 PID: 153 at lib/objagg.c:170 objagg_obj_parent_assign+0xb5/0xd0 Modules linked in: CPU: 0 PID: 153 Comm: kworker/0:18 Not tainted 6.9.0-rc6-custom-g70fbc2c1c38b #42 Hardware name: Mellanox Technologies Ltd. MSN3700C/VMOD0008, BIOS 5.11 10/10/2018 Workqueue: mlxsw_core mlxsw_sp_acl_tcam_vregion_rehash_work RIP: 0010:objagg_obj_parent_assign+0xb5/0xd0 [...] Call Trace: <TASK> __objagg_obj_get+0x2bb/0x580 objagg_obj_get+0xe/0x80 mlxsw_sp_acl_erp_mask_get+0xb5/0xf0 mlxsw_sp_acl_atcam_entry_add+0xe8/0x3c0 mlxsw_sp_acl_tcam_entry_create+0x5e/0xa0 mlxsw_sp_acl_tcam_vchunk_migrate_one+0x16b/0x270 mlxsw_sp_acl_tcam_vregion_rehash_work+0xbe/0x510 process_one_work+0x151/0x370 Fixes: 9069a38 ("lib: objagg: implement optimization hints assembly and use hints for object creation") Signed-off-by: Ido Schimmel <[email protected]> Reviewed-by: Amit Cohen <[email protected]> Tested-by: Alexander Zubkov <[email protected]> Signed-off-by: Petr Machata <[email protected]> Reviewed-by: Simon Horman <[email protected]> Signed-off-by: David S. Miller <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
anthraxx
pushed a commit
that referenced
this issue
Aug 7, 2024
[ Upstream commit 97d833c ] ACLs in Spectrum-2 and newer ASICs can reside in the algorithmic TCAM (A-TCAM) or in the ordinary circuit TCAM (C-TCAM). The former can contain more ACLs (i.e., tc filters), but the number of masks in each region (i.e., tc chain) is limited. In order to mitigate the effects of the above limitation, the device allows filters to share a single mask if their masks only differ in up to 8 consecutive bits. For example, dst_ip/25 can be represented using dst_ip/24 with a delta of 1 bit. The C-TCAM does not have a limit on the number of masks being used (and therefore does not support mask aggregation), but can contain a limited number of filters. The driver uses the "objagg" library to perform the mask aggregation by passing it objects that consist of the filter's mask and whether the filter is to be inserted into the A-TCAM or the C-TCAM since filters in different TCAMs cannot share a mask. The set of created objects is dependent on the insertion order of the filters and is not necessarily optimal. Therefore, the driver will periodically ask the library to compute a more optimal set ("hints") by looking at all the existing objects. When the library asks the driver whether two objects can be aggregated the driver only compares the provided masks and ignores the A-TCAM / C-TCAM indication. This is the right thing to do since the goal is to move as many filters as possible to the A-TCAM. The driver also forbids two identical masks from being aggregated since this can only happen if one was intentionally put in the C-TCAM to avoid a conflict in the A-TCAM. The above can result in the following set of hints: H1: {mask X, A-TCAM} -> H2: {mask Y, A-TCAM} // X is Y + delta H3: {mask Y, C-TCAM} -> H4: {mask Z, A-TCAM} // Y is Z + delta After getting the hints from the library the driver will start migrating filters from one region to another while consulting the computed hints and instructing the device to perform a lookup in both regions during the transition. Assuming a filter with mask X is being migrated into the A-TCAM in the new region, the hints lookup will return H1. Since H2 is the parent of H1, the library will try to find the object associated with it and create it if necessary in which case another hints lookup (recursive) will be performed. This hints lookup for {mask Y, A-TCAM} will either return H2 or H3 since the driver passes the library an object comparison function that ignores the A-TCAM / C-TCAM indication. This can eventually lead to nested objects which are not supported by the library [1]. Fix by removing the object comparison function from both the driver and the library as the driver was the only user. That way the lookup will only return exact matches. I do not have a reliable reproducer that can reproduce the issue in a timely manner, but before the fix the issue would reproduce in several minutes and with the fix it does not reproduce in over an hour. Note that the current usefulness of the hints is limited because they include the C-TCAM indication and represent aggregation that cannot actually happen. This will be addressed in net-next. [1] WARNING: CPU: 0 PID: 153 at lib/objagg.c:170 objagg_obj_parent_assign+0xb5/0xd0 Modules linked in: CPU: 0 PID: 153 Comm: kworker/0:18 Not tainted 6.9.0-rc6-custom-g70fbc2c1c38b #42 Hardware name: Mellanox Technologies Ltd. MSN3700C/VMOD0008, BIOS 5.11 10/10/2018 Workqueue: mlxsw_core mlxsw_sp_acl_tcam_vregion_rehash_work RIP: 0010:objagg_obj_parent_assign+0xb5/0xd0 [...] Call Trace: <TASK> __objagg_obj_get+0x2bb/0x580 objagg_obj_get+0xe/0x80 mlxsw_sp_acl_erp_mask_get+0xb5/0xf0 mlxsw_sp_acl_atcam_entry_add+0xe8/0x3c0 mlxsw_sp_acl_tcam_entry_create+0x5e/0xa0 mlxsw_sp_acl_tcam_vchunk_migrate_one+0x16b/0x270 mlxsw_sp_acl_tcam_vregion_rehash_work+0xbe/0x510 process_one_work+0x151/0x370 Fixes: 9069a38 ("lib: objagg: implement optimization hints assembly and use hints for object creation") Signed-off-by: Ido Schimmel <[email protected]> Reviewed-by: Amit Cohen <[email protected]> Tested-by: Alexander Zubkov <[email protected]> Signed-off-by: Petr Machata <[email protected]> Reviewed-by: Simon Horman <[email protected]> Signed-off-by: David S. Miller <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
anthraxx
pushed a commit
that referenced
this issue
Aug 23, 2024
[ Upstream commit 97d833c ] ACLs in Spectrum-2 and newer ASICs can reside in the algorithmic TCAM (A-TCAM) or in the ordinary circuit TCAM (C-TCAM). The former can contain more ACLs (i.e., tc filters), but the number of masks in each region (i.e., tc chain) is limited. In order to mitigate the effects of the above limitation, the device allows filters to share a single mask if their masks only differ in up to 8 consecutive bits. For example, dst_ip/25 can be represented using dst_ip/24 with a delta of 1 bit. The C-TCAM does not have a limit on the number of masks being used (and therefore does not support mask aggregation), but can contain a limited number of filters. The driver uses the "objagg" library to perform the mask aggregation by passing it objects that consist of the filter's mask and whether the filter is to be inserted into the A-TCAM or the C-TCAM since filters in different TCAMs cannot share a mask. The set of created objects is dependent on the insertion order of the filters and is not necessarily optimal. Therefore, the driver will periodically ask the library to compute a more optimal set ("hints") by looking at all the existing objects. When the library asks the driver whether two objects can be aggregated the driver only compares the provided masks and ignores the A-TCAM / C-TCAM indication. This is the right thing to do since the goal is to move as many filters as possible to the A-TCAM. The driver also forbids two identical masks from being aggregated since this can only happen if one was intentionally put in the C-TCAM to avoid a conflict in the A-TCAM. The above can result in the following set of hints: H1: {mask X, A-TCAM} -> H2: {mask Y, A-TCAM} // X is Y + delta H3: {mask Y, C-TCAM} -> H4: {mask Z, A-TCAM} // Y is Z + delta After getting the hints from the library the driver will start migrating filters from one region to another while consulting the computed hints and instructing the device to perform a lookup in both regions during the transition. Assuming a filter with mask X is being migrated into the A-TCAM in the new region, the hints lookup will return H1. Since H2 is the parent of H1, the library will try to find the object associated with it and create it if necessary in which case another hints lookup (recursive) will be performed. This hints lookup for {mask Y, A-TCAM} will either return H2 or H3 since the driver passes the library an object comparison function that ignores the A-TCAM / C-TCAM indication. This can eventually lead to nested objects which are not supported by the library [1]. Fix by removing the object comparison function from both the driver and the library as the driver was the only user. That way the lookup will only return exact matches. I do not have a reliable reproducer that can reproduce the issue in a timely manner, but before the fix the issue would reproduce in several minutes and with the fix it does not reproduce in over an hour. Note that the current usefulness of the hints is limited because they include the C-TCAM indication and represent aggregation that cannot actually happen. This will be addressed in net-next. [1] WARNING: CPU: 0 PID: 153 at lib/objagg.c:170 objagg_obj_parent_assign+0xb5/0xd0 Modules linked in: CPU: 0 PID: 153 Comm: kworker/0:18 Not tainted 6.9.0-rc6-custom-g70fbc2c1c38b #42 Hardware name: Mellanox Technologies Ltd. MSN3700C/VMOD0008, BIOS 5.11 10/10/2018 Workqueue: mlxsw_core mlxsw_sp_acl_tcam_vregion_rehash_work RIP: 0010:objagg_obj_parent_assign+0xb5/0xd0 [...] Call Trace: <TASK> __objagg_obj_get+0x2bb/0x580 objagg_obj_get+0xe/0x80 mlxsw_sp_acl_erp_mask_get+0xb5/0xf0 mlxsw_sp_acl_atcam_entry_add+0xe8/0x3c0 mlxsw_sp_acl_tcam_entry_create+0x5e/0xa0 mlxsw_sp_acl_tcam_vchunk_migrate_one+0x16b/0x270 mlxsw_sp_acl_tcam_vregion_rehash_work+0xbe/0x510 process_one_work+0x151/0x370 Fixes: 9069a38 ("lib: objagg: implement optimization hints assembly and use hints for object creation") Signed-off-by: Ido Schimmel <[email protected]> Reviewed-by: Amit Cohen <[email protected]> Tested-by: Alexander Zubkov <[email protected]> Signed-off-by: Petr Machata <[email protected]> Reviewed-by: Simon Horman <[email protected]> Signed-off-by: David S. Miller <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
anthraxx
pushed a commit
that referenced
this issue
Aug 23, 2024
[ Upstream commit 97d833c ] ACLs in Spectrum-2 and newer ASICs can reside in the algorithmic TCAM (A-TCAM) or in the ordinary circuit TCAM (C-TCAM). The former can contain more ACLs (i.e., tc filters), but the number of masks in each region (i.e., tc chain) is limited. In order to mitigate the effects of the above limitation, the device allows filters to share a single mask if their masks only differ in up to 8 consecutive bits. For example, dst_ip/25 can be represented using dst_ip/24 with a delta of 1 bit. The C-TCAM does not have a limit on the number of masks being used (and therefore does not support mask aggregation), but can contain a limited number of filters. The driver uses the "objagg" library to perform the mask aggregation by passing it objects that consist of the filter's mask and whether the filter is to be inserted into the A-TCAM or the C-TCAM since filters in different TCAMs cannot share a mask. The set of created objects is dependent on the insertion order of the filters and is not necessarily optimal. Therefore, the driver will periodically ask the library to compute a more optimal set ("hints") by looking at all the existing objects. When the library asks the driver whether two objects can be aggregated the driver only compares the provided masks and ignores the A-TCAM / C-TCAM indication. This is the right thing to do since the goal is to move as many filters as possible to the A-TCAM. The driver also forbids two identical masks from being aggregated since this can only happen if one was intentionally put in the C-TCAM to avoid a conflict in the A-TCAM. The above can result in the following set of hints: H1: {mask X, A-TCAM} -> H2: {mask Y, A-TCAM} // X is Y + delta H3: {mask Y, C-TCAM} -> H4: {mask Z, A-TCAM} // Y is Z + delta After getting the hints from the library the driver will start migrating filters from one region to another while consulting the computed hints and instructing the device to perform a lookup in both regions during the transition. Assuming a filter with mask X is being migrated into the A-TCAM in the new region, the hints lookup will return H1. Since H2 is the parent of H1, the library will try to find the object associated with it and create it if necessary in which case another hints lookup (recursive) will be performed. This hints lookup for {mask Y, A-TCAM} will either return H2 or H3 since the driver passes the library an object comparison function that ignores the A-TCAM / C-TCAM indication. This can eventually lead to nested objects which are not supported by the library [1]. Fix by removing the object comparison function from both the driver and the library as the driver was the only user. That way the lookup will only return exact matches. I do not have a reliable reproducer that can reproduce the issue in a timely manner, but before the fix the issue would reproduce in several minutes and with the fix it does not reproduce in over an hour. Note that the current usefulness of the hints is limited because they include the C-TCAM indication and represent aggregation that cannot actually happen. This will be addressed in net-next. [1] WARNING: CPU: 0 PID: 153 at lib/objagg.c:170 objagg_obj_parent_assign+0xb5/0xd0 Modules linked in: CPU: 0 PID: 153 Comm: kworker/0:18 Not tainted 6.9.0-rc6-custom-g70fbc2c1c38b #42 Hardware name: Mellanox Technologies Ltd. MSN3700C/VMOD0008, BIOS 5.11 10/10/2018 Workqueue: mlxsw_core mlxsw_sp_acl_tcam_vregion_rehash_work RIP: 0010:objagg_obj_parent_assign+0xb5/0xd0 [...] Call Trace: <TASK> __objagg_obj_get+0x2bb/0x580 objagg_obj_get+0xe/0x80 mlxsw_sp_acl_erp_mask_get+0xb5/0xf0 mlxsw_sp_acl_atcam_entry_add+0xe8/0x3c0 mlxsw_sp_acl_tcam_entry_create+0x5e/0xa0 mlxsw_sp_acl_tcam_vchunk_migrate_one+0x16b/0x270 mlxsw_sp_acl_tcam_vregion_rehash_work+0xbe/0x510 process_one_work+0x151/0x370 Fixes: 9069a38 ("lib: objagg: implement optimization hints assembly and use hints for object creation") Signed-off-by: Ido Schimmel <[email protected]> Reviewed-by: Amit Cohen <[email protected]> Tested-by: Alexander Zubkov <[email protected]> Signed-off-by: Petr Machata <[email protected]> Reviewed-by: Simon Horman <[email protected]> Signed-off-by: David S. Miller <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
anthraxx
pushed a commit
that referenced
this issue
Aug 23, 2024
[ Upstream commit 97d833c ] ACLs in Spectrum-2 and newer ASICs can reside in the algorithmic TCAM (A-TCAM) or in the ordinary circuit TCAM (C-TCAM). The former can contain more ACLs (i.e., tc filters), but the number of masks in each region (i.e., tc chain) is limited. In order to mitigate the effects of the above limitation, the device allows filters to share a single mask if their masks only differ in up to 8 consecutive bits. For example, dst_ip/25 can be represented using dst_ip/24 with a delta of 1 bit. The C-TCAM does not have a limit on the number of masks being used (and therefore does not support mask aggregation), but can contain a limited number of filters. The driver uses the "objagg" library to perform the mask aggregation by passing it objects that consist of the filter's mask and whether the filter is to be inserted into the A-TCAM or the C-TCAM since filters in different TCAMs cannot share a mask. The set of created objects is dependent on the insertion order of the filters and is not necessarily optimal. Therefore, the driver will periodically ask the library to compute a more optimal set ("hints") by looking at all the existing objects. When the library asks the driver whether two objects can be aggregated the driver only compares the provided masks and ignores the A-TCAM / C-TCAM indication. This is the right thing to do since the goal is to move as many filters as possible to the A-TCAM. The driver also forbids two identical masks from being aggregated since this can only happen if one was intentionally put in the C-TCAM to avoid a conflict in the A-TCAM. The above can result in the following set of hints: H1: {mask X, A-TCAM} -> H2: {mask Y, A-TCAM} // X is Y + delta H3: {mask Y, C-TCAM} -> H4: {mask Z, A-TCAM} // Y is Z + delta After getting the hints from the library the driver will start migrating filters from one region to another while consulting the computed hints and instructing the device to perform a lookup in both regions during the transition. Assuming a filter with mask X is being migrated into the A-TCAM in the new region, the hints lookup will return H1. Since H2 is the parent of H1, the library will try to find the object associated with it and create it if necessary in which case another hints lookup (recursive) will be performed. This hints lookup for {mask Y, A-TCAM} will either return H2 or H3 since the driver passes the library an object comparison function that ignores the A-TCAM / C-TCAM indication. This can eventually lead to nested objects which are not supported by the library [1]. Fix by removing the object comparison function from both the driver and the library as the driver was the only user. That way the lookup will only return exact matches. I do not have a reliable reproducer that can reproduce the issue in a timely manner, but before the fix the issue would reproduce in several minutes and with the fix it does not reproduce in over an hour. Note that the current usefulness of the hints is limited because they include the C-TCAM indication and represent aggregation that cannot actually happen. This will be addressed in net-next. [1] WARNING: CPU: 0 PID: 153 at lib/objagg.c:170 objagg_obj_parent_assign+0xb5/0xd0 Modules linked in: CPU: 0 PID: 153 Comm: kworker/0:18 Not tainted 6.9.0-rc6-custom-g70fbc2c1c38b #42 Hardware name: Mellanox Technologies Ltd. MSN3700C/VMOD0008, BIOS 5.11 10/10/2018 Workqueue: mlxsw_core mlxsw_sp_acl_tcam_vregion_rehash_work RIP: 0010:objagg_obj_parent_assign+0xb5/0xd0 [...] Call Trace: <TASK> __objagg_obj_get+0x2bb/0x580 objagg_obj_get+0xe/0x80 mlxsw_sp_acl_erp_mask_get+0xb5/0xf0 mlxsw_sp_acl_atcam_entry_add+0xe8/0x3c0 mlxsw_sp_acl_tcam_entry_create+0x5e/0xa0 mlxsw_sp_acl_tcam_vchunk_migrate_one+0x16b/0x270 mlxsw_sp_acl_tcam_vregion_rehash_work+0xbe/0x510 process_one_work+0x151/0x370 Fixes: 9069a38 ("lib: objagg: implement optimization hints assembly and use hints for object creation") Signed-off-by: Ido Schimmel <[email protected]> Reviewed-by: Amit Cohen <[email protected]> Tested-by: Alexander Zubkov <[email protected]> Signed-off-by: Petr Machata <[email protected]> Reviewed-by: Simon Horman <[email protected]> Signed-off-by: David S. Miller <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
anthraxx
pushed a commit
that referenced
this issue
Nov 6, 2024
…d addresses [ Upstream commit 48771da ] Commit 50c6dbd ("x86/ioremap: Improve iounmap() address range checks") introduces a WARN when adrress ranges of iounmap are invalid. On Thinkpad P1 Gen 7 (Meteor Lake-P) this caused the following warning to appear: WARNING: CPU: 7 PID: 713 at arch/x86/mm/ioremap.c:461 iounmap+0x58/0x1f0 Modules linked in: rfkill(+) snd_timer(+) fjes(+) snd soundcore intel_pmc_core(+) int3403_thermal(+) int340x_thermal_zone intel_vsec pmt_telemetry acpi_pad pmt_class acpi_tad int3400_thermal acpi_thermal_rel joydev loop nfnetlink zram xe drm_suballoc_helper nouveau i915 mxm_wmi drm_ttm_helper gpu_sched drm_gpuvm drm_exec drm_buddy i2c_algo_bit crct10dif_pclmul crc32_pclmul ttm crc32c_intel polyval_clmulni rtsx_pci_sdmmc ucsi_acpi polyval_generic mmc_core hid_multitouch drm_display_helper ghash_clmulni_intel typec_ucsi nvme sha512_ssse3 video sha256_ssse3 nvme_core intel_vpu sha1_ssse3 rtsx_pci cec typec nvme_auth i2c_hid_acpi i2c_hid wmi pinctrl_meteorlake serio_raw ip6_tables ip_tables fuse CPU: 7 UID: 0 PID: 713 Comm: (udev-worker) Not tainted 6.12.0-rc2iounmap+ #42 Hardware name: LENOVO 21KWCTO1WW/21KWCTO1WW, BIOS N48ET19W (1.06 ) 07/18/2024 RIP: 0010:iounmap+0x58/0x1f0 Code: 85 6a 01 00 00 48 8b 05 e6 e2 28 04 48 39 c5 72 19 eb 26 cc cc cc 48 ba 00 00 00 00 00 00 32 00 48 8d 44 02 ff 48 39 c5 72 23 <0f> 0b 48 83 c4 08 5b 5d 41 5c c3 cc cc cc cc 48 ba 00 00 00 00 00 RSP: 0018:ffff888131eff038 EFLAGS: 00010207 RAX: ffffc90000000000 RBX: 0000000000000000 RCX: ffff888e33b80000 RDX: dffffc0000000000 RSI: ffff888e33bc29c0 RDI: 0000000000000000 RBP: 0000000000000000 R08: ffff8881598a8000 R09: ffff888e2ccedc10 R10: 0000000000000003 R11: ffffffffb3367634 R12: 00000000fe000000 R13: ffff888101d0da28 R14: ffffffffc2e437e0 R15: ffff888110b03b28 FS: 00007f3c1d4b3980(0000) GS:ffff888e33b80000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00005651cfc93578 CR3: 0000000124e4c002 CR4: 0000000000f70ef0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000ffff07f0 DR7: 0000000000000400 PKRU: 55555554 Call Trace: <TASK> ? __warn.cold+0xb6/0x176 ? iounmap+0x58/0x1f0 ? report_bug+0x1f4/0x2b0 ? handle_bug+0x58/0x90 ? exc_invalid_op+0x17/0x40 ? asm_exc_invalid_op+0x1a/0x20 ? iounmap+0x58/0x1f0 pmc_core_ssram_get_pmc+0x477/0x6c0 [intel_pmc_core] ? __pfx_pmc_core_ssram_get_pmc+0x10/0x10 [intel_pmc_core] ? __pfx_do_pci_enable_device+0x10/0x10 ? pci_wait_for_pending+0x60/0x110 ? pci_enable_device_flags+0x1e3/0x2e0 ? __pfx_mtl_core_init+0x10/0x10 [intel_pmc_core] pmc_core_ssram_init+0x7f/0x110 [intel_pmc_core] mtl_core_init+0xda/0x130 [intel_pmc_core] ? __mutex_init+0xb9/0x130 pmc_core_probe+0x27e/0x10b0 [intel_pmc_core] ? _raw_spin_lock_irqsave+0x96/0xf0 ? __pfx_pmc_core_probe+0x10/0x10 [intel_pmc_core] ? __pfx_mutex_unlock+0x10/0x10 ? __pfx_mutex_lock+0x10/0x10 ? device_pm_check_callbacks+0x82/0x370 ? acpi_dev_pm_attach+0x234/0x2b0 platform_probe+0x9f/0x150 really_probe+0x1e0/0x8a0 __driver_probe_device+0x18c/0x370 ? __pfx___driver_attach+0x10/0x10 driver_probe_device+0x4a/0x120 __driver_attach+0x190/0x4a0 ? __pfx___driver_attach+0x10/0x10 bus_for_each_dev+0x103/0x180 ? __pfx_bus_for_each_dev+0x10/0x10 ? klist_add_tail+0x136/0x270 bus_add_driver+0x2fc/0x540 driver_register+0x1a5/0x360 ? __pfx_pmc_core_driver_init+0x10/0x10 [intel_pmc_core] do_one_initcall+0xa4/0x380 ? __pfx_do_one_initcall+0x10/0x10 ? kasan_unpoison+0x44/0x70 do_init_module+0x296/0x800 load_module+0x5090/0x6ce0 ? __pfx_load_module+0x10/0x10 ? ima_post_read_file+0x193/0x200 ? __pfx_ima_post_read_file+0x10/0x10 ? rw_verify_area+0x152/0x4c0 ? kernel_read_file+0x257/0x750 ? __pfx_kernel_read_file+0x10/0x10 ? __pfx_filemap_get_read_batch+0x10/0x10 ? init_module_from_file+0xd1/0x130 init_module_from_file+0xd1/0x130 ? __pfx_init_module_from_file+0x10/0x10 ? __pfx__raw_spin_lock+0x10/0x10 ? __pfx_cred_has_capability.isra.0+0x10/0x10 idempotent_init_module+0x236/0x770 ? __pfx_idempotent_init_module+0x10/0x10 ? fdget+0x58/0x3f0 ? security_capable+0x7d/0x110 __x64_sys_finit_module+0xbe/0x130 do_syscall_64+0x82/0x160 ? __pfx_filemap_read+0x10/0x10 ? __pfx___fsnotify_parent+0x10/0x10 ? vfs_read+0x3a6/0xa30 ? vfs_read+0x3a6/0xa30 ? __seccomp_filter+0x175/0xc60 ? __pfx___seccomp_filter+0x10/0x10 ? fdget_pos+0x1ce/0x500 ? syscall_exit_to_user_mode_prepare+0x149/0x170 ? syscall_exit_to_user_mode+0x10/0x210 ? do_syscall_64+0x8e/0x160 ? switch_fpu_return+0xe3/0x1f0 ? syscall_exit_to_user_mode+0x1d5/0x210 ? do_syscall_64+0x8e/0x160 ? exc_page_fault+0x76/0xf0 entry_SYSCALL_64_after_hwframe+0x76/0x7e RIP: 0033:0x7f3c1d6d155d Code: ff c3 66 2e 0f 1f 84 00 00 00 00 00 90 f3 0f 1e fa 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 83 58 0f 00 f7 d8 64 89 01 48 RSP: 002b:00007ffe6309db38 EFLAGS: 00000246 ORIG_RAX: 0000000000000139 RAX: ffffffffffffffda RBX: 0000557c212550a0 RCX: 00007f3c1d6d155d RDX: 0000000000000000 RSI: 00007f3c1cd943bd RDI: 0000000000000025 RBP: 00007ffe6309dbf0 R08: 00007f3c1d7c7b20 R09: 00007ffe6309db80 R10: 0000557c21255270 R11: 0000000000000246 R12: 00007f3c1cd943bd R13: 0000000000020000 R14: 0000557c21255c80 R15: 0000557c21255240 </TASK> no_free_ptr(tmp_ssram) sets tmp_ssram NULL while assigning ssram. pmc_core_iounmap calls iounmap unconditionally causing the above warning to appear during boot. Fix it by checking for a valid address before calling iounmap. Also in the function pmc_core_ssram_get_pmc return -ENOMEM when ioremap fails similar to other instances in the file. Fixes: a01486d ("platform/x86/intel/pmc: Cleanup SSRAM discovery") Reviewed-by: Ilpo Järvinen <[email protected]> Reviewed-by: David E. Box <[email protected]> Signed-off-by: Vamsi Krishna Brahmajosyula <[email protected]> Link: https://lore.kernel.org/r/[email protected] Reviewed-by: Hans de Goede <[email protected]> Signed-off-by: Hans de Goede <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment
Hi. Can you please consider creating debs in an apt repo for releases? This would increase uptake and make the kernel readily usable by downstream distros like us (Whonix). Also when new security fixes are made it will be much faster to get a newer version out for the masses.
As far as security goes, everyone will be using auditable and signed builds (if you're using reproducible build infrastructure) that will greatly reduce attacks against dev machines by nefarious actors.
The text was updated successfully, but these errors were encountered: