Additions for optional ABC axes

Adapted from electrokean@b3e6d6a

grbl/config.h

@@ -35,6 +35,7 @@
 // one configuration file by placing their specific defaults and pin map at the bottom of this file.
 // If doing so, simply comment out these two defines and see instructions below.
 #define DEFAULTS_GENERIC
+#define DEFAULTS_ABC_AXIS
 #define CPU_MAP_2560_INITIAL
 
 // Serial baud rate
@@ -105,6 +106,9 @@
 #define HOMING_CYCLE_0 (1<<Z_AXIS)                // REQUIRED: First move Z to clear workspace.
 #define HOMING_CYCLE_1 ((1<<X_AXIS)|(1<<Y_AXIS))  // OPTIONAL: Then move X,Y at the same time.
 // #define HOMING_CYCLE_2                         // OPTIONAL: Uncomment and add axes mask to enable
+// #define HOMING_CYCLE_3                         // OPTIONAL: Uncomment and add axes mask to enable
+// #define HOMING_CYCLE_4                         // OPTIONAL: Uncomment and add axes mask to enable
+// #define HOMING_CYCLE_5                         // OPTIONAL: Uncomment and add axes mask to enable
 
 // NOTE: The following are two examples to setup homing for 2-axis machines.
 // #define HOMING_CYCLE_0 ((1<<X_AXIS)|(1<<Y_AXIS))  // NOT COMPATIBLE WITH COREXY: Homes both X-Y in one cycle. 

grbl/cpu_map.h

@@ -39,7 +39,10 @@
   #define X_STEP_BIT    2 // MEGA2560 Digital Pin 24
   #define Y_STEP_BIT    3 // MEGA2560 Digital Pin 25
   #define Z_STEP_BIT    4 // MEGA2560 Digital Pin 26
-  #define STEP_MASK ((1<<X_STEP_BIT)|(1<<Y_STEP_BIT)|(1<<Z_STEP_BIT)) // All step bits
+  #define A_STEP_BIT    5 // MEGA2560 Digital Pin 27
+  #define B_STEP_BIT    6 // MEGA2560 Digital Pin 28
+  #define C_STEP_BIT    7 // MEGA2560 Digital Pin 29
+  #define STEP_MASK ((1<<X_STEP_BIT)|(1<<Y_STEP_BIT)|(1<<Z_STEP_BIT)|(1<<A_STEP_BIT)|(1<<B_STEP_BIT)|(1<<C_STEP_BIT)) // All step bits
 
   // Define step direction output pins. NOTE: All direction pins must be on the same port.
   #define DIRECTION_DDR     DDRC
@@ -48,7 +51,10 @@
   #define X_DIRECTION_BIT   7 // MEGA2560 Digital Pin 30
   #define Y_DIRECTION_BIT   6 // MEGA2560 Digital Pin 31
   #define Z_DIRECTION_BIT   5 // MEGA2560 Digital Pin 32
-  #define DIRECTION_MASK ((1<<X_DIRECTION_BIT)|(1<<Y_DIRECTION_BIT)|(1<<Z_DIRECTION_BIT)) // All direction bits
+  #define A_DIRECTION_BIT   4 // MEGA2560 Digital Pin 33
+  #define B_DIRECTION_BIT   3 // MEGA2560 Digital Pin 34
+  #define C_DIRECTION_BIT   2 // MEGA2560 Digital Pin 35
+  #define DIRECTION_MASK ((1<<X_DIRECTION_BIT)|(1<<Y_DIRECTION_BIT)|(1<<Z_DIRECTION_BIT)|(1<<A_DIRECTION_BIT)|(1<<B_DIRECTION_BIT)|(1<<C_DIRECTION_BIT)) // All direction bits
 
   // Define stepper driver enable/disable output pin.
   #define STEPPERS_DISABLE_DDR   DDRB
@@ -64,10 +70,13 @@
   #define X_LIMIT_BIT     4 // MEGA2560 Digital Pin 10
   #define Y_LIMIT_BIT     5 // MEGA2560 Digital Pin 11
   #define Z_LIMIT_BIT     6 // MEGA2560 Digital Pin 12
+  #define A_LIMIT_BIT     0 // MEGA2560 Digital Pin 53
+  #define B_LIMIT_BIT     1 // MEGA2560 Digital Pin 52
+  #define C_LIMIT_BIT     2 // MEGA2560 Digital Pin 51
   #define LIMIT_INT       PCIE0  // Pin change interrupt enable pin
   #define LIMIT_INT_vect  PCINT0_vect 
   #define LIMIT_PCMSK     PCMSK0 // Pin change interrupt register
-  #define LIMIT_MASK ((1<<X_LIMIT_BIT)|(1<<Y_LIMIT_BIT)|(1<<Z_LIMIT_BIT)) // All limit bits
+  #define LIMIT_MASK ((1<<X_LIMIT_BIT)|(1<<Y_LIMIT_BIT)|(1<<Z_LIMIT_BIT)|(1<<A_LIMIT_BIT)|(1<<B_LIMIT_BIT)|(1<<C_LIMIT_BIT)) // All limit bits
 
   // Define spindle enable and spindle direction output pins.
   #define SPINDLE_ENABLE_DDR      DDRH

grbl/defaults.h

@@ -452,4 +452,21 @@
   #define DEFAULT_HOMING_PULLOFF 1.0 // mm
 #endif
 
+#ifdef DEFAULTS_ABC_AXIS
+  #define DEFAULT_A_STEPS_PER_MM 250.0
+  #define DEFAULT_A_MAX_RATE 500.0 // mm/min
+  #define DEFAULT_A_ACCELERATION (10.0*60*60) // 10*60*60 mm/min^2 = 10 mm/sec^2
+  #define DEFAULT_A_MAX_TRAVEL 200.0 // mm
+
+  #define DEFAULT_B_STEPS_PER_MM 250.0
+  #define DEFAULT_B_MAX_RATE 500.0 // mm/min
+  #define DEFAULT_B_ACCELERATION (10.0*60*60) // 10*60*60 mm/min^2 = 10 mm/sec^2
+  #define DEFAULT_B_MAX_TRAVEL 200.0 // mm
+
+  #define DEFAULT_C_STEPS_PER_MM 250.0
+  #define DEFAULT_C_MAX_RATE 500.0 // mm/min
+  #define DEFAULT_C_ACCELERATION (10.0*60*60) // 10*60*60 mm/min^2 = 10 mm/sec^2
+  #define DEFAULT_C_MAX_TRAVEL 200.0 // mm
+#endif
+
 #endif

grbl/gcode.c

@@ -282,6 +282,16 @@ uint8_t gc_execute_line(char *line)
            legal g-code words and stores their value. Error-checking is performed later since some
            words (I,J,K,L,P,R) have multiple connotations and/or depend on the issued commands. */
         switch(letter){
+#ifdef A_AXIS
+          case 'A': word_bit = WORD_A; gc_block.values.xyz[A_AXIS] = value; axis_words |= (1<<A_AXIS); break;
+#endif
+#ifdef B_AXIS
+          case 'B': word_bit = WORD_B; gc_block.values.xyz[B_AXIS] = value; axis_words |= (1<<B_AXIS); break;
+#endif
+#ifdef C_AXIS
+          case 'C': word_bit = WORD_C; gc_block.values.xyz[C_AXIS] = value; axis_words |= (1<<C_AXIS); break;
+#endif
+
           // case 'A': // Not supported
           // case 'B': // Not supported
           // case 'C': // Not supported
@@ -810,7 +820,7 @@ uint8_t gc_execute_line(char *line)
   } else {
     bit_false(value_words,(bit(WORD_N)|bit(WORD_F)|bit(WORD_S)|bit(WORD_T))); // Remove single-meaning value words.
   }
-  if (axis_command) { bit_false(value_words,(bit(WORD_X)|bit(WORD_Y)|bit(WORD_Z))); } // Remove axis words.
+  if (axis_command) { bit_false(value_words,(bit(WORD_X)|bit(WORD_Y)|bit(WORD_Z)|bit(WORD_A)|bit(WORD_B)|bit(WORD_C))); } // Remove axis words.
   if (value_words) { FAIL(STATUS_GCODE_UNUSED_WORDS); } // [Unused words]
 
   /* -------------------------------------------------------------------------------------

grbl/gcode.h

@@ -144,6 +144,10 @@
 #define WORD_Y  11
 #define WORD_Z  12
 
+#define WORD_A  13
+#define WORD_B  14
+#define WORD_C  15
+
 // Define g-code parser position updating flags
 #define GC_UPDATE_POS_TARGET   0 // Must be zero
 #define GC_UPDATE_POS_SYSTEM   1
@@ -199,7 +203,7 @@ typedef struct {
   float r;         // Arc radius
   float s;         // Spindle speed
   uint8_t t;       // Tool selection
-  float xyz[3];    // X,Y,Z Translational axes
+  float xyz[N_AXIS];    // X,Y,Z Translational axes
 } gc_values_t;
 
 

grbl/motion_control.c

@@ -227,6 +227,15 @@ void mc_homing_cycle(uint8_t cycle_mask)
     #ifdef HOMING_CYCLE_2
       limits_go_home(HOMING_CYCLE_2);  // Homing cycle 2
     #endif
+    #ifdef HOMING_CYCLE_3
+      limits_go_home(HOMING_CYCLE_3);  // Homing cycle 3
+    #endif
+    #ifdef HOMING_CYCLE_4
+      limits_go_home(HOMING_CYCLE_4);  // Homing cycle 4
+    #endif
+    #ifdef HOMING_CYCLE_5
+      limits_go_home(HOMING_CYCLE_5);  // Homing cycle 5
+    #endif
   }
 
   protocol_execute_realtime(); // Check for reset and set system abort.

grbl/nuts_bolts.h

@@ -28,11 +28,13 @@
 #define SOME_LARGE_VALUE 1.0E+38
 
 // Axis array index values. Must start with 0 and be continuous.
-#define N_AXIS 3 // Number of axes
+#define N_AXIS 6 // Number of axes
 #define X_AXIS 0 // Axis indexing value.
 #define Y_AXIS 1
 #define Z_AXIS 2
-// #define A_AXIS 3
+#define A_AXIS 3
+#define B_AXIS 4
+#define C_AXIS 5
 
 // CoreXY motor assignments. DO NOT ALTER.
 // NOTE: If the A and B motor axis bindings are changed, this effects the CoreXY equations.

grbl/report.c

@@ -520,6 +520,15 @@ void report_realtime_status()
         if (bit_istrue(lim_pin_state,bit(X_AXIS))) { serial_write('X'); }
         if (bit_istrue(lim_pin_state,bit(Y_AXIS))) { serial_write('Y'); }
         if (bit_istrue(lim_pin_state,bit(Z_AXIS))) { serial_write('Z'); }
+#ifdef A_AXIS
+        if (bit_istrue(lim_pin_state,bit(A_AXIS))) { serial_write('A'); }
+#endif
+#ifdef B_AXIS
+        if (bit_istrue(lim_pin_state,bit(B_AXIS))) { serial_write('B'); }
+#endif
+#ifdef C_AXIS
+        if (bit_istrue(lim_pin_state,bit(C_AXIS))) { serial_write('C'); }
+#endif
       }
       if (ctrl_pin_state) {
         #ifdef ENABLE_SAFETY_DOOR_INPUT_PIN

grbl/settings.c

@@ -107,6 +107,25 @@ void settings_restore(uint8_t restore_flag) {
     settings.max_travel[Y_AXIS] = (-DEFAULT_Y_MAX_TRAVEL);
     settings.max_travel[Z_AXIS] = (-DEFAULT_Z_MAX_TRAVEL);
 
+#ifdef A_AXIS
+    settings.steps_per_mm[A_AXIS] = DEFAULT_A_STEPS_PER_MM;
+    settings.max_rate[A_AXIS] = DEFAULT_A_MAX_RATE;
+    settings.acceleration[A_AXIS] = DEFAULT_A_ACCELERATION;
+    settings.max_travel[A_AXIS] = (-DEFAULT_A_MAX_TRAVEL);
+#endif
+#ifdef B_AXIS
+    settings.steps_per_mm[B_AXIS] = DEFAULT_B_STEPS_PER_MM;
+    settings.max_rate[B_AXIS] = DEFAULT_B_MAX_RATE;
+    settings.acceleration[B_AXIS] = DEFAULT_B_ACCELERATION;
+    settings.max_travel[B_AXIS] = (-DEFAULT_B_MAX_TRAVEL);
+#endif
+#ifdef C_AXIS
+    settings.steps_per_mm[C_AXIS] = DEFAULT_C_STEPS_PER_MM;
+    settings.acceleration[C_AXIS] = DEFAULT_C_ACCELERATION;
+    settings.max_rate[C_AXIS] = DEFAULT_C_MAX_RATE;
+    settings.max_travel[C_AXIS] = (-DEFAULT_C_MAX_TRAVEL);
+#endif
+
     write_global_settings();
   }
 
@@ -317,7 +336,20 @@ uint8_t get_step_pin_mask(uint8_t axis_idx)
 {
   if ( axis_idx == X_AXIS ) { return((1<<X_STEP_BIT)); }
   if ( axis_idx == Y_AXIS ) { return((1<<Y_STEP_BIT)); }
+#if defined(A_AXIS) || defined(B_AXIS) || defined(C_AXIS)
+  if ( axis_idx == Z_AXIS ) { return((1<<Z_STEP_BIT)); }
+#endif
+#ifdef A_AXIS
+  if ( axis_idx == A_AXIS ) { return((1<<A_STEP_BIT)); }
+#endif
+#ifdef B_AXIS
+  if ( axis_idx == B_AXIS ) { return((1<<B_STEP_BIT)); }
+#endif
+#ifdef C_AXIS
+  return((1<<C_STEP_BIT));
+#else
   return((1<<Z_STEP_BIT));
+#endif
 }
 
 
@@ -326,7 +358,20 @@ uint8_t get_direction_pin_mask(uint8_t axis_idx)
 {
   if ( axis_idx == X_AXIS ) { return((1<<X_DIRECTION_BIT)); }
   if ( axis_idx == Y_AXIS ) { return((1<<Y_DIRECTION_BIT)); }
+#if defined(A_AXIS) || defined(B_AXIS) || defined(C_AXIS)
+  if ( axis_idx == Z_AXIS ) { return((1<<Z_DIRECTION_BIT)); }
+#endif
+#ifdef A_AXIS
+  if ( axis_idx == A_AXIS ) { return((1<<A_DIRECTION_BIT)); }
+#endif
+#ifdef B_AXIS
+  if ( axis_idx == B_AXIS ) { return((1<<B_DIRECTION_BIT)); }
+#endif
+#ifdef C_AXIS
+  return((1<<C_DIRECTION_BIT));
+#else
   return((1<<Z_DIRECTION_BIT));
+#endif
 }
 
 
@@ -335,5 +380,18 @@ uint8_t get_limit_pin_mask(uint8_t axis_idx)
 {
   if ( axis_idx == X_AXIS ) { return((1<<X_LIMIT_BIT)); }
   if ( axis_idx == Y_AXIS ) { return((1<<Y_LIMIT_BIT)); }
-  return((1<<Z_LIMIT_BIT));
+#if defined(A_AXIS) || defined(B_AXIS) || defined(C_AXIS)
+  if ( axis_idx == Z_AXIS ) { return((1<<Z_LIMIT_BIT)); }
+#endif
+#ifdef A_AXIS
+  if ( axis_idx == A_AXIS ) { return((1<<A_LIMIT_BIT)); }
+#endif
+#ifdef B_AXIS
+  if ( axis_idx == B_AXIS ) { return((1<<B_LIMIT_BIT)); }
+#endif
+#ifdef C_AXIS
+  return((1<<C_LIMIT_BIT));
+#else
+   return((1<<Z_LIMIT_BIT));
+#endif
 }

grbl/stepper.c

@@ -87,7 +87,18 @@ typedef struct {
   // Used by the bresenham line algorithm
   uint32_t counter_x,        // Counter variables for the bresenham line tracer
            counter_y,
-           counter_z;
+           counter_z
+#ifdef A_AXIS
+          , counter_a
+#endif
+#ifdef B_AXIS
+          , counter_b
+#endif
+#ifdef C_AXIS
+          , counter_c
+#endif
+          ;
+
   #ifdef STEP_PULSE_DELAY
     uint8_t step_bits;  // Stores out_bits output to complete the step pulse delay
   #endif
@@ -347,6 +358,16 @@ ISR(TIMER1_COMPA_vect)
         st.steps[X_AXIS] = st.exec_block->steps[X_AXIS] >> st.exec_segment->amass_level;
         st.steps[Y_AXIS] = st.exec_block->steps[Y_AXIS] >> st.exec_segment->amass_level;
         st.steps[Z_AXIS] = st.exec_block->steps[Z_AXIS] >> st.exec_segment->amass_level;
+#ifdef A_AXIS
+        st.steps[A_AXIS] = st.exec_block->steps[A_AXIS] >> st.exec_segment->amass_level;
+#endif
+#ifdef B_AXIS
+        st.steps[B_AXIS] = st.exec_block->steps[B_AXIS] >> st.exec_segment->amass_level;
+#endif
+#ifdef C_AXIS
+        st.steps[C_AXIS] = st.exec_block->steps[C_AXIS] >> st.exec_segment->amass_level;
+#endif
+
       #endif
 
       // Set real-time spindle output as segment is loaded, just prior to the first step.
@@ -404,6 +425,46 @@ ISR(TIMER1_COMPA_vect)
     else { sys_position[Z_AXIS]++; }
   }
 
+#ifdef A_AXIS
+  #ifdef ADAPTIVE_MULTI_AXIS_STEP_SMOOTHING
+    st.counter_a += st.steps[A_AXIS];
+  #else
+    st.counter_a += st.exec_block->steps[A_AXIS];
+  #endif
+  if (st.counter_a > st.exec_block->step_event_count) {
+    st.step_outbits |= (1<<A_STEP_BIT);
+    st.counter_a -= st.exec_block->step_event_count;
+    if (st.exec_block->direction_bits & (1<<A_DIRECTION_BIT)) { sys_position[A_AXIS]--; }
+    else { sys_position[A_AXIS]++; }
+  }
+#endif
+#ifdef B_AXIS
+  #ifdef ADAPTIVE_MULTI_AXIS_STEP_SMOOTHING
+    st.counter_b += st.steps[B_AXIS];
+  #else
+    st.counter_b += st.exec_block->steps[B_AXIS];
+  #endif
+  if (st.counter_b > st.exec_block->step_event_count) {
+    st.step_outbits |= (1<<B_STEP_BIT);
+    st.counter_b -= st.exec_block->step_event_count;
+    if (st.exec_block->direction_bits & (1<<B_DIRECTION_BIT)) { sys_position[B_AXIS]--; }
+    else { sys_position[B_AXIS]++; }
+  }
+#endif
+#ifdef C_AXIS
+  #ifdef ADAPTIVE_MULTI_AXIS_STEP_SMOOTHING
+    st.counter_c += st.steps[C_AXIS];
+  #else
+    st.counter_c += st.exec_block->steps[C_AXIS];
+  #endif
+  if (st.counter_c > st.exec_block->step_event_count) {
+    st.step_outbits |= (1<<C_STEP_BIT);
+    st.counter_c -= st.exec_block->step_event_count;
+    if (st.exec_block->direction_bits & (1<<C_DIRECTION_BIT)) { sys_position[C_AXIS]--; }
+    else { sys_position[C_AXIS]++; }
+  }
+#endif
+
   // During a homing cycle, lock out and prevent desired axes from moving.
   if (sys.state == STATE_HOMING) { st.step_outbits &= sys.homing_axis_lock; }