[platform] Add a new supported platform, Delta-ag9032v1 (#1168)

CPU : Intel Rangeley C2538
    Swich ASIC: Broadcom Tomahawk BCM56960
    Ports : 32x100G
    Switch SKU : Delta-ag9032v1

Signed-off-by: neal <[email protected]>

device/delta/x86_64-delta_ag9032v1-r0/Delta-ag9032v1/port_config.ini

@@ -0,0 +1,33 @@
+# name          lanes                 alias
+Ethernet0       49,50,51,52           hundredGigE1/1
+Ethernet4       53,54,55,56           hundredGigE1/2
+Ethernet8       57,58,59,60           hundredGigE1/3
+Ethernet12      61,62,63,64           hundredGigE1/4
+Ethernet16      65,66,67,68           hundredGigE1/5
+Ethernet20      69,70,71,72           hundredGigE1/6
+Ethernet24      73,74,75,76           hundredGigE1/7
+Ethernet28      77,78,79,80           hundredGigE1/8
+Ethernet32      37,38,39,40           hundredGigE1/9
+Ethernet36      33,34,35,36           hundredGigE1/10
+Ethernet40      45,46,47,48           hundredGigE1/11
+Ethernet44      41,42,43,44           hundredGigE1/12
+Ethernet48      81,82,83,84           hundredGigE1/13
+Ethernet52      85,86,87,88           hundredGigE1/14
+Ethernet56      89,90,91,92           hundredGigE1/15
+Ethernet60      93,94,95,96           hundredGigE1/16
+Ethernet64      97,98,99,100          hundredGigE1/17
+Ethernet68      101,102,103,104       hundredGigE1/18
+Ethernet72      105,106,107,108       hundredGigE1/19
+Ethernet76      109,110,111,112       hundredGigE1/20
+Ethernet80      21,22,23,24           hundredGigE1/21
+Ethernet84      17,18,19,20           hundredGigE1/22
+Ethernet88      29,30,31,32           hundredGigE1/23
+Ethernet92      25,26,27,28           hundredGigE1/24
+Ethernet96      117,118,119,120       hundredGigE1/25
+Ethernet100     113,114,115,116       hundredGigE1/26
+Ethernet104     125,126,127,128       hundredGigE1/27
+Ethernet108     121,122,123,124       hundredGigE1/28
+Ethernet112     5,6,7,8               hundredGigE1/29
+Ethernet116     1,2,3,4               hundredGigE1/30
+Ethernet120     13,14,15,16           hundredGigE1/31
+Ethernet124     9,10,11,12            hundredGigE1/32

device/delta/x86_64-delta_ag9032v1-r0/Delta-ag9032v1/sai.profile

@@ -0,0 +1 @@
+SAI_INIT_CONFIG_FILE=/etc/bcm/th-ag9032v1-32x100G.config.bcm

device/delta/x86_64-delta_ag9032v1-r0/fancontrol

@@ -0,0 +1,10 @@
+INTERVAL=10
+DEVPATH=hwmon1=/sys/bus/i2c/devices
+DEVNAME=hwmon1=emc2305
+FCTEMPS=hwmon1/2-004d/hwmon/hwmon*/temp1_input hwmon1/7-004c/hwmon/hwmon*/temp1_input hwmon1/7-004d/hwmon/hwmon*/temp1_input hwmon1/7-004e/hwmon/hwmon*/temp1_input hwmon1/30-004f/hwmon/hwmon*/temp1_input hwmon1/40-0058/temp1_input hwmon1/41-0058/temp1_input
+
+FCFANS=hwmon1/37-002c/fan1_input hwmon1/37-002c/fan2_input hwmon1/37-002c/fan3_input hwmon1/37-002c/fan4_input hwmon1/37-002c/fan5_input hwmon1/38-002d/fan1_input hwmon1/38-002d/fan2_input hwmon1/38-002d/fan3_input hwmon1/38-002d/fan4_input hwmon1/38-002d/fan5_input
+MINTEMP=20
+MAXTEMP=60
+MINSTART=75
+MINSTOP=22

device/delta/x86_64-delta_ag9032v1-r0/fancontrol.service

@@ -0,0 +1,244 @@
+#!/bin/bash
+#
+# Simple script implementing a temperature dependent fan speed control
+# Supported Linux kernel versions: 2.6.5 and later
+#
+# Version 0.70
+#
+# Usage: fancontrol [CONFIGFILE]
+#
+# Dependencies:
+#   bash, egrep, sed, cut, sleep, readlink, lm_sensors :)
+#
+# Please send any questions, comments or success stories to
+# [email protected]
+# Thanks!
+#
+# For configuration instructions and warnings please see fancontrol.txt, which
+# can be found in the doc/ directory or at the website mentioned above.
+#
+#
+#    Copyright 2003 Marius Reiner <[email protected]>
+#    Copyright (C) 2007-2009 Jean Delvare <[email protected]>
+#
+#    This program is free software; you can redistribute it and/or modify
+#    it under the terms of the GNU General Public License as published by
+#    the Free Software Foundation; either version 2 of the License, or
+#    (at your option) any later version.
+#
+#    This program is distributed in the hope that it will be useful,
+#    but WITHOUT ANY WARRANTY; without even the implied warranty of
+#    MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+#    GNU General Public License for more details.
+#
+#    You should have received a copy of the GNU General Public License
+#    along with this program; if not, write to the Free Software
+#    Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+#    MA 02110-1301 USA.
+#
+#
+
+PIDFILE="/var/run/fancontrol.pid"
+
+#DEBUG=1
+MAX=255
+
+function LoadConfig
+{
+	local fcvcount fcv
+
+	echo "Loading configuration from $1 ..."
+	if [ ! -r "$1" ]
+	then
+		echo "Error: Can't read configuration file" >&2
+		exit 1
+	fi
+
+	# grep configuration from file
+	INTERVAL=`egrep '^INTERVAL=.*$' $1 | sed -e 's/INTERVAL=//g'`
+	DEVPATH=`egrep '^DEVPATH=.*$' $1 | sed -e 's/DEVPATH= *//g'`
+	DEVNAME=`egrep '^DEVNAME=.*$' $1 | sed -e 's/DEVNAME= *//g'`
+	FCTEMPS=`egrep '^FCTEMPS=.*$' $1 | sed -e 's/FCTEMPS=//g'`
+	MINTEMP=`egrep '^MINTEMP=.*$' $1 | sed -e 's/MINTEMP=//g'`
+	MAXTEMP=`egrep '^MAXTEMP=.*$' $1 | sed -e 's/MAXTEMP=//g'`
+	MINSTART=`egrep '^MINSTART=.*$' $1 | sed -e 's/MINSTART=//g'`
+	MINSTOP=`egrep '^MINSTOP=.*$' $1 | sed -e 's/MINSTOP=//g'`
+	HWMON=$( echo "$DEVPATH" | sed 's/=.*$//g')
+	FCDEVPATH=$( echo "$DEVPATH" | sed 's/^.*=//g')
+	FCMINTEMP=$MINTEMP
+	FCMAXTEMP=$MAXTEMP
+	FCMINSTART=$MINSTART
+	FCMINSTOP=$MINSTOP
+
+	FCFANS=`egrep '^FCFANS=.*$' $1 | sed -e 's/FCFANS=//g'`
+
+	# Check whether all mandatory settings are set
+	if [[ -z ${INTERVAL} || -z ${FCTEMPS} || -z ${MINTEMP} || -z ${MAXTEMP} || -z ${MINSTART} || -z ${MINSTOP} ]]
+	then
+		echo "Some mandatory settings missing, please check your config file!" >&2
+		exit 1
+	fi
+	if [ "$INTERVAL" -le 0 ]
+	then
+		echo "Error in configuration file:" >&2
+		echo "INTERVAL must be at least 1" >&2
+		exit 1
+	fi
+
+	# write settings to arrays for easier use and print them
+	echo
+	echo "Common settings:"
+
+	temp_string=$FCTEMPS
+
+	let fcvcount=0
+	for fcv in $FCTEMPS
+	do
+		fcvcount=$((fcvcount+1))
+		AFCTEMP[$fcvcount]=$( echo "$temp_string" | cut -d" " -f $fcvcount )
+		AFCTEMP[$fcvcount]=$( echo "${AFCTEMP[$fcvcount]}" | sed 's/hwmon1/\/sys\/bus\/i2c\/devices/g' )
+		AFCTEMP_PATH[$fcvcount]=$( echo "${AFCTEMP[$fcvcount]}" | sed 's/hwmon1/\/sys\/bus\/i2c\/devices/g' )
+
+        AFCTEMP[$fcvcount]=$( cat ${AFCTEMP[$fcvcount]} )
+		AFCTEMP[$fcvcount]=$(( AFCTEMP[$fcvcount]/1000 ))
+	done
+
+	fan_string=$FCFANS
+	fcvcount=0
+	zero=0
+	for fcv in $FCFANS
+	do
+		fcvcount=$((fcvcount+1))
+		AFCFAN[$fcvcount]=$( echo "$fan_string" | cut -d" " -f $fcvcount )
+		AFCFAN_PATH[$fcvcount]=$( echo "${AFCFAN[$fcvcount]}" | sed 's/hwmon1/\/sys\/bus\/i2c\/devices/g' )
+		AFCFAN_TARGET[$fcvcount]=$( echo "${AFCFAN_PATH[$fcvcount]}" | sed 's/hwmon1/\/sys\/bus\/i2c\/devices/g' )
+		AFCFAN_TARGET[$fcvcount]=$( echo "${AFCFAN_TARGET[$fcvcount]}"  | sed 's/$/_percentage/g')
+		AFCFAN[$fcvcount]=$( cat ${AFCFAN_PATH[$fcvcount]} )
+		if [ "${AFCFAN[$fcvcount]}" == 960 ]
+		then
+			AFCFAN[$fcvcount]=$zero
+		fi
+	done
+}
+
+# Check that all referenced sysfs files exist
+function CheckFiles
+{
+	local outdated=0 fcvcount tsen fan
+	if [ $outdated -eq 1 ]
+	then
+		echo >&2
+		echo "At least one referenced file is missing. Either some required kernel" >&2
+		echo "modules haven't been loaded, or your configuration file is outdated." >&2
+		echo "In the latter case, you should run pwmconfig again." >&2
+	fi
+	return $outdated
+}
+
+LoadConfig $1
+
+# Detect path to sensors
+if [ ! -d $DIR ]
+then
+	echo $0: 'No sensors found! (did you load the necessary modules?)' >&2
+	exit 1
+fi
+cd $DIR
+
+# Check for configuration change
+if [ "$DIR" != "/" ] && [ -z "$DEVPATH" -o -z "$DEVNAME" ]
+then
+	echo "Configuration is too old, please run pwmconfig again" >&2
+	exit 1
+fi
+if [ "$DIR" = "/" -a -n "$DEVPATH" ]
+then
+	echo "Unneeded DEVPATH with absolute device paths" >&2
+	exit 1
+fi
+CheckFiles || exit 1
+
+if [ -f "$PIDFILE" ]
+then
+	echo "File $PIDFILE exists, is fancontrol already running?" >&2
+	exit 1
+fi
+echo $$ > "$PIDFILE"
+
+
+# main function
+function UpdateThermalSensors
+{
+	echo ""
+	TEMP_HIGHEST=0
+	FAN_PERCENTAGE=0
+
+	for i in ${AFCTEMP_PATH[@]}; do 
+    	if (( $(cat $i) > $TEMP_HIGHEST )); then 
+        	TEMP_HIGHEST=$(cat $i); 
+    	fi;
+	done
+	TEMP_HIGHEST=$((TEMP_HIGHEST/1000))
+	echo "The highest temperature of thermal sensors: $TEMP_HIGHEST °C"
+}
+
+function UpdateFanSpeeds
+{
+	if [ $TEMP_HIGHEST -lt 51 ]; then #TEMP<=50
+    	FAN_PERCENTAGE=40
+	elif [ $TEMP_HIGHEST -lt 56 -a $TEMP_HIGHEST -gt 50 ]; then #50<TEMP<=55
+	    FAN_PERCENTAGE=60
+	elif [ $TEMP_HIGHEST -lt 61 -a $TEMP_HIGHEST -gt 55 ]; then #55<TEMP<=60
+	    FAN_PERCENTAGE=80
+	elif [ $TEMP_HIGHEST -lt 66 -a $TEMP_HIGHEST -gt 60 ]; then #60<TEMP<=65
+	    FAN_PERCENTAGE=90
+	elif [ $TEMP_HIGHEST -gt 65 ]; then # 65<TEMP
+	    FAN_PERCENTAGE=100
+	else
+	    FAN_PERCENTAGE=100
+	fi
+
+	echo "Trying to set fan speed to $FAN_PERCENTAGE %"
+	#Set speed to fan1~fan10
+	let fcvcount=0
+	for fcv in $FCFANS
+	do
+		fcvcount=$(( fcvcount + 1 ))
+		echo  $FAN_PERCENTAGE > ${AFCFAN_TARGET[$fcvcount]} 
+		AFCFAN[$fcvcount]=$( cat ${AFCFAN_PATH[$fcvcount]} )
+
+		if [ "${AFCFAN[$fcvcount]}" == 960 ]
+		then
+			AFCFAN[$fcvcount]=$zero
+		fi
+	done
+
+	if [ $TEMP_HIGHEST -lt 51 ]; then #TEMP<=50
+    	FAN_ON_PSU_PERCENTAGE=50
+	elif [ $TEMP_HIGHEST -lt 100 -a $TEMP_HIGHEST -gt 50 ]; then #50<TEMP<100
+		FAN_ON_PSU_PERCENTAGE=100
+	else
+		echo "Unable to get thermal temperature"
+		FAN_ON_PSU_PERCENTAGE=100
+	fi
+	#Set speed to PSU_FAN1
+	#echo  "0x00" > '/sys/bus/i2c/devices/4-0058/psu_select_member'
+	echo "$FAN_ON_PSU_PERCENTAGE" > '/sys/bus/i2c/devices/40-0058/fan1_set_percentage'
+	echo "PSU fan1 =$( cat '/sys/bus/i2c/devices/40-0058/fan1_input' ) (rpm)"
+	#Set speed to PSU_FAN2
+	#echo  "0x20" > '/sys/bus/i2c/devices/4-0058/psu_select_member'
+	echo "$FAN_ON_PSU_PERCENTAGE" > '/sys/bus/i2c/devices/41-0058/fan1_set_percentage'
+	echo "PSU fan2 =$( cat '/sys/bus/i2c/devices/41-0058/fan1_input' ) (rpm)"
+
+	rm -f "$PIDFILE"
+}
+# main loop calling the main function at specified intervals
+while true
+do
+	UpdateThermalSensors
+	UpdateFanSpeeds
+	echo "Sleep $INTERVAL seconds ..."
+	# Sleep while still handling signals
+	sleep $INTERVAL &
+	wait $!
+done

device/delta/x86_64-delta_ag9032v1-r0/installer.conf

@@ -0,0 +1,2 @@
+CONSOLE_PORT=0x3f8
+CONSOLE_SPEED=115200

device/delta/x86_64-delta_ag9032v1-r0/led_proc_init.soc

@@ -0,0 +1,45 @@
+s CMIC_LEDUP0_PROGRAM_RAM 0
+s CMIC_LEDUP1_PROGRAM_RAM 0
+
+led 0 stop
+led 0 prog 02 00 60 E0 86 ED 2E E0 32 08 97 02 00 0E 00 60 E3 2E E0 32 00 32 01 B7 97 02 00 0E 00 12 E7 50 86 E0 86 E0 86 E0 86 E0 16 E7 61 EB 06 E3 67 4E 67 66 67 66 67 66 67 66 67 66 67 66 67 66 67 66 67 66 67 66 67 66 06 E0 D2 40 74 06 3A C0 D2 01 74 66 06 EB D2 00 70 62 16 ED 99 99 1A 00 71 62 77 66 32 0F 87 57 32 0E 87 57
+led 0 auto on
+led 0 start
+m CMIC_LEDUP0_PORT_ORDER_REMAP_0_3 REMAP_PORT_0=31 REMAP_PORT_1=30 REMAP_PORT_2=29 REMAP_PORT_3=28
+m CMIC_LEDUP0_PORT_ORDER_REMAP_4_7 REMAP_PORT_4=27 REMAP_PORT_5=26 REMAP_PORT_6=25 REMAP_PORT_7=24
+m CMIC_LEDUP0_PORT_ORDER_REMAP_8_11 REMAP_PORT_8=23 REMAP_PORT_9=22 REMAP_PORT_10=21 REMAP_PORT_11=20
+m CMIC_LEDUP0_PORT_ORDER_REMAP_12_15 REMAP_PORT_12=19 REMAP_PORT_13=18 REMAP_PORT_14=17 REMAP_PORT_15=16
+m CMIC_LEDUP0_PORT_ORDER_REMAP_16_19 REMAP_PORT_16=15 REMAP_PORT_17=14 REMAP_PORT_18=13 REMAP_PORT_19=12
+m CMIC_LEDUP0_PORT_ORDER_REMAP_20_23 REMAP_PORT_20=11 REMAP_PORT_21=10 REMAP_PORT_22=9 REMAP_PORT_23=8
+m CMIC_LEDUP0_PORT_ORDER_REMAP_24_27 REMAP_PORT_24=7 REMAP_PORT_25=6 REMAP_PORT_26=5 REMAP_PORT_27=4
+m CMIC_LEDUP0_PORT_ORDER_REMAP_28_31 REMAP_PORT_28=3 REMAP_PORT_29=2 REMAP_PORT_30=1 REMAP_PORT_31=0
+m CMIC_LEDUP0_PORT_ORDER_REMAP_32_35 REMAP_PORT_32=63 REMAP_PORT_33=62 REMAP_PORT_34=61 REMAP_PORT_35=60
+m CMIC_LEDUP0_PORT_ORDER_REMAP_36_39 REMAP_PORT_36=59 REMAP_PORT_37=58 REMAP_PORT_38=57 REMAP_PORT_39=56
+m CMIC_LEDUP0_PORT_ORDER_REMAP_40_43 REMAP_PORT_40=55 REMAP_PORT_41=54 REMAP_PORT_42=53 REMAP_PORT_43=52
+m CMIC_LEDUP0_PORT_ORDER_REMAP_44_47 REMAP_PORT_44=51 REMAP_PORT_45=50 REMAP_PORT_46=49 REMAP_PORT_47=48
+m CMIC_LEDUP0_PORT_ORDER_REMAP_48_51 REMAP_PORT_48=47 REMAP_PORT_49=46 REMAP_PORT_50=45 REMAP_PORT_51=44
+m CMIC_LEDUP0_PORT_ORDER_REMAP_52_55 REMAP_PORT_52=43 REMAP_PORT_53=42 REMAP_PORT_54=41 REMAP_PORT_55=40
+m CMIC_LEDUP0_PORT_ORDER_REMAP_56_59 REMAP_PORT_56=39 REMAP_PORT_57=38 REMAP_PORT_58=37 REMAP_PORT_59=36
+m CMIC_LEDUP0_PORT_ORDER_REMAP_60_63 REMAP_PORT_60=35 REMAP_PORT_61=34 REMAP_PORT_62=33 REMAP_PORT_63=32
+
+led 1 stop
+led 1 prog 02 00 60 E0 86 ED 2E E0 32 08 97 02 00 0E 00 60 E3 2E E0 32 00 32 01 B7 97 02 00 0E 00 12 E7 50 86 E0 86 E0 86 E0 86 E0 16 E7 61 EB 06 E3 67 4E 67 66 67 66 67 66 67 66 67 66 67 66 67 66 67 66 67 66 67 66 67 66 06 E0 D2 40 74 06 3A C0 D2 01 74 66 06 EB D2 00 70 62 16 ED 99 99 1A 00 71 62 77 66 32 0F 87 57 32 0E 87 57
+led 1 auto on
+led 1 start
+m CMIC_LEDUP1_PORT_ORDER_REMAP_0_3 REMAP_PORT_0=3 REMAP_PORT_1=2 REMAP_PORT_2=1 REMAP_PORT_3=0
+m CMIC_LEDUP1_PORT_ORDER_REMAP_4_7 REMAP_PORT_4=7 REMAP_PORT_5=6 REMAP_PORT_6=5 REMAP_PORT_7=4
+m CMIC_LEDUP1_PORT_ORDER_REMAP_8_11 REMAP_PORT_8=11 REMAP_PORT_9=10 REMAP_PORT_10=9 REMAP_PORT_11=8
+m CMIC_LEDUP1_PORT_ORDER_REMAP_12_15 REMAP_PORT_12=15 REMAP_PORT_13=14 REMAP_PORT_14=13 REMAP_PORT_15=12
+m CMIC_LEDUP1_PORT_ORDER_REMAP_16_19 REMAP_PORT_16=19 REMAP_PORT_17=18 REMAP_PORT_18=17 REMAP_PORT_19=16
+m CMIC_LEDUP1_PORT_ORDER_REMAP_20_23 REMAP_PORT_20=23 REMAP_PORT_21=22 REMAP_PORT_22=21 REMAP_PORT_23=20
+m CMIC_LEDUP1_PORT_ORDER_REMAP_24_27 REMAP_PORT_24=27 REMAP_PORT_25=26 REMAP_PORT_26=25 REMAP_PORT_27=24
+m CMIC_LEDUP1_PORT_ORDER_REMAP_28_31 REMAP_PORT_28=31 REMAP_PORT_29=30 REMAP_PORT_30=29 REMAP_PORT_31=28
+m CMIC_LEDUP1_PORT_ORDER_REMAP_32_35 REMAP_PORT_32=35 REMAP_PORT_33=34 REMAP_PORT_34=33 REMAP_PORT_35=32
+m CMIC_LEDUP1_PORT_ORDER_REMAP_36_39 REMAP_PORT_36=39 REMAP_PORT_37=38 REMAP_PORT_38=37 REMAP_PORT_39=36
+m CMIC_LEDUP1_PORT_ORDER_REMAP_40_43 REMAP_PORT_40=43 REMAP_PORT_41=42 REMAP_PORT_42=41 REMAP_PORT_43=40
+m CMIC_LEDUP1_PORT_ORDER_REMAP_44_47 REMAP_PORT_44=47 REMAP_PORT_45=46 REMAP_PORT_46=45 REMAP_PORT_47=44
+m CMIC_LEDUP1_PORT_ORDER_REMAP_48_51 REMAP_PORT_48=51 REMAP_PORT_49=50 REMAP_PORT_50=49 REMAP_PORT_51=48
+m CMIC_LEDUP1_PORT_ORDER_REMAP_52_55 REMAP_PORT_52=55 REMAP_PORT_53=54 REMAP_PORT_54=53 REMAP_PORT_55=52
+m CMIC_LEDUP1_PORT_ORDER_REMAP_56_59 REMAP_PORT_56=59 REMAP_PORT_57=58 REMAP_PORT_58=57 REMAP_PORT_59=56
+m CMIC_LEDUP1_PORT_ORDER_REMAP_60_63 REMAP_PORT_60=63 REMAP_PORT_61=62 REMAP_PORT_62=61 REMAP_PORT_63=60
+