Teensy 4.1 Ethernet support (MarlinFirmware#19801)

Marlin/Configuration.h

@@ -107,7 +107,8 @@
 
 /**
  * Select a secondary serial port on the board to use for communication with the host.
- * :[-1, 0, 1, 2, 3, 4, 5, 6, 7]
+ * Currently Ethernet (-2) is only supported on Teensy 4.1 boards.
+ * :[-2, -1, 0, 1, 2, 3, 4, 5, 6, 7]
  */
 //#define SERIAL_PORT_2 -1
 

Marlin/Configuration_adv.h

@@ -3456,6 +3456,13 @@
                               // Default behavior is limited to Z axis only.
 #endif
 
+/**
+ * Ethernet. Use M552 to enable and set the IP address.
+ */
+#if HAS_ETHERNET
+  #define MAC_ADDRESS { 0xDE, 0xAD, 0xBE, 0xEF, 0xF0, 0x0D }  // A MAC address unique to your network
+#endif
+
 /**
  * WiFi Support (Espressif ESP32 WiFi)
  */

Marlin/src/HAL/TEENSY40_41/HAL.h

@@ -66,6 +66,8 @@
 #ifdef SERIAL_PORT_2
   #if SERIAL_PORT_2 == -1
     #define MYSERIAL1 usbSerial
+  #elif SERIAL_PORT_2 == -2
+    #define MYSERIAL1 ethernet.telnetClient
   #elif WITHIN(SERIAL_PORT_2, 0, 8)
     #define MYSERIAL1 MSERIAL(SERIAL_PORT_2)
   #else

Marlin/src/MarlinCore.cpp

@@ -77,6 +77,10 @@
   #include "lcd/dwin/e3v2/rotary_encoder.h"
 #endif
 
+#if HAS_ETHERNET
+  #include "feature/ethernet.h"
+#endif
+
 #if ENABLED(IIC_BL24CXX_EEPROM)
   #include "libs/BL24CXX.h"
 #endif
@@ -713,6 +717,9 @@ void idle(TERN_(ADVANCED_PAUSE_FEATURE, bool no_stepper_sleep/*=false*/)) {
     HAL_idletask();
   #endif
 
+  // Check network connection
+  TERN_(HAS_ETHERNET, ethernet.check());
+
   // Handle Power-Loss Recovery
   #if ENABLED(POWER_LOSS_RECOVERY) && PIN_EXISTS(POWER_LOSS)
     if (printJobOngoing()) recovery.outage();
@@ -968,7 +975,7 @@ void setup() {
   MYSERIAL0.begin(BAUDRATE);
   uint32_t serial_connect_timeout = millis() + 1000UL;
   while (!MYSERIAL0 && PENDING(millis(), serial_connect_timeout)) { /*nada*/ }
-  #if HAS_MULTI_SERIAL
+  #if HAS_MULTI_SERIAL && !HAS_ETHERNET
     MYSERIAL1.begin(BAUDRATE);
     serial_connect_timeout = millis() + 1000UL;
     while (!MYSERIAL1 && PENDING(millis(), serial_connect_timeout)) { /*nada*/ }
@@ -1090,6 +1097,10 @@ void setup() {
   SETUP_RUN(settings.first_load());   // Load data from EEPROM if available (or use defaults)
                                       // This also updates variables in the planner, elsewhere
 
+  #if HAS_ETHERNET
+    SETUP_RUN(ethernet.init());
+  #endif
+
   #if HAS_TOUCH_XPT2046
     SETUP_RUN(touch.init());
   #endif

Marlin/src/core/serial.h

@@ -23,6 +23,10 @@
 
 #include "../inc/MarlinConfig.h"
 
+#if HAS_ETHERNET
+  #include "../feature/ethernet.h"
+#endif
+
 /**
  * Define debug bit-masks
  */
@@ -56,8 +60,9 @@ extern uint8_t marlin_debug_flags;
     #define SERIAL_OUT(WHAT, V...) (void)CAT(MYSERIAL,SERIAL_CATCHALL).WHAT(V)
   #else
     #define SERIAL_OUT(WHAT, V...) do{ \
-      if (!serial_port_index || serial_port_index == SERIAL_BOTH) (void)MYSERIAL0.WHAT(V); \
-      if ( serial_port_index) (void)MYSERIAL1.WHAT(V); \
+      const bool port2_open = TERN1(HAS_ETHERNET, ethernet.have_telnet_client); \
+      if ( serial_port_index == 0 || serial_port_index == SERIAL_BOTH)                (void)MYSERIAL0.WHAT(V); \
+      if ((serial_port_index == 1 || serial_port_index == SERIAL_BOTH) && port2_open) (void)MYSERIAL1.WHAT(V); \
     }while(0)
   #endif
 

Marlin/src/feature/ethernet.cpp

@@ -0,0 +1,175 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <https://www.gnu.org/licenses/>.
+ *
+ */
+
+#include "../inc/MarlinConfigPre.h"
+
+#if HAS_ETHERNET
+
+#include "ethernet.h"
+#include "../core/serial.h"
+
+#define DEBUG_OUT ENABLED(DEBUG_ETHERNET)
+#include "../core/debug_out.h"
+
+bool MarlinEthernet::hardware_enabled, // = false
+     MarlinEthernet::have_telnet_client; // = false
+
+IPAddress MarlinEthernet::ip,
+          MarlinEthernet::myDns,
+          MarlinEthernet::gateway,
+          MarlinEthernet::subnet;
+
+EthernetClient  MarlinEthernet::telnetClient;  // connected client
+
+MarlinEthernet ethernet;
+
+EthernetServer server(23);    // telnet server
+
+enum linkStates { UNLINKED, LINKING, LINKED, CONNECTING, CONNECTED, NO_HARDWARE } linkState;
+
+#ifdef __IMXRT1062__
+
+  static void teensyMAC(uint8_t * const mac) {
+    const uint32_t m1 = HW_OCOTP_MAC1, m2 = HW_OCOTP_MAC0;
+    mac[0] = m1 >> 8;
+    mac[1] = m1 >> 0;
+    mac[2] = m2 >> 24;
+    mac[3] = m2 >> 16;
+    mac[4] = m2 >> 8;
+    mac[5] = m2 >> 0;
+  }
+
+#else
+
+  byte mac[] = MAC_ADDRESS;
+
+#endif
+
+void ethernet_cable_error() { SERIAL_ERROR_MSG("Ethernet cable is not connected."); }
+
+void MarlinEthernet::init() {
+  if (!hardware_enabled) return;
+
+  SERIAL_ECHO_MSG("Starting network...");
+
+  // Init the Ethernet device
+  #ifdef __IMXRT1062__
+    uint8_t mac[6];
+    teensyMAC(mac);
+  #endif
+
+  if (!ip) {
+    Ethernet.begin(mac); // use DHCP
+  }
+  else {
+    if (!gateway) {
+      gateway = ip;
+      gateway[3] = 1;
+      myDns = gateway;
+      subnet = IPAddress(255,255,255,0);
+    }
+    if (!myDns) myDns = gateway;
+    if (!subnet) subnet = IPAddress(255,255,255,0);
+    Ethernet.begin(mac, ip, myDns, gateway, subnet);
+  }
+
+  // Check for Ethernet hardware present
+  if (Ethernet.hardwareStatus() == EthernetNoHardware) {
+    SERIAL_ERROR_MSG("No Ethernet hardware found.");
+    linkState = NO_HARDWARE;
+    return;
+  }
+
+  linkState = UNLINKED;
+
+  if (Ethernet.linkStatus() == LinkOFF)
+    ethernet_cable_error();
+}
+
+void MarlinEthernet::check() {
+  if (!hardware_enabled) return;
+
+  switch (linkState) {
+    case NO_HARDWARE:
+      break;
+
+    case UNLINKED:
+      if (Ethernet.linkStatus() == LinkOFF) break;
+
+      SERIAL_ECHOLNPGM("Ethernet cable connected");
+      server.begin();
+      linkState = LINKING;
+      break;
+
+    case LINKING:
+      if (!Ethernet.localIP()) break;
+
+      SERIAL_ECHOPGM("Successfully started telnet server with IP ");
+      MYSERIAL0.println(Ethernet.localIP());
+
+      linkState = LINKED;
+      break;
+
+    case LINKED:
+      if (Ethernet.linkStatus() == LinkOFF) {
+        ethernet_cable_error();
+        linkState = UNLINKED;
+        break;
+      }
+      telnetClient = server.accept();
+      if (telnetClient) linkState = CONNECTING;
+      break;
+
+    case CONNECTING:
+      telnetClient.println("Marlin " SHORT_BUILD_VERSION);
+      #if defined(STRING_DISTRIBUTION_DATE) && defined(STRING_CONFIG_H_AUTHOR)
+        telnetClient.println(
+          " Last Updated: " STRING_DISTRIBUTION_DATE
+          " | Author: " STRING_CONFIG_H_AUTHOR
+        );
+      #endif
+      telnetClient.println("Compiled: " __DATE__);
+
+      SERIAL_ECHOLNPGM("Client connected");
+      have_telnet_client = true;
+      linkState = CONNECTED;
+      break;
+
+    case CONNECTED:
+      if (telnetClient && !telnetClient.connected()) {
+        SERIAL_ECHOLNPGM("Client disconnected");
+        telnetClient.stop();
+        have_telnet_client = false;
+        linkState = LINKED;
+      }
+      if (Ethernet.linkStatus() == LinkOFF) {
+        ethernet_cable_error();
+        if (telnetClient) telnetClient.stop();
+        linkState = UNLINKED;
+      }
+      break;
+
+    default: break;
+  }
+}
+
+#endif // HAS_ETHERNET

Marlin/src/feature/ethernet.h

@@ -0,0 +1,39 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <https://www.gnu.org/licenses/>.
+ *
+ */
+#pragma once
+
+#ifdef __IMXRT1062__
+  #include <NativeEthernet.h>
+#endif
+
+// Teensy 4.1 uses internal MAC Address
+
+class MarlinEthernet {
+  public:
+    static bool hardware_enabled, have_telnet_client;
+    static IPAddress ip, myDns, gateway, subnet;
+    static EthernetClient telnetClient;
+    static void init();
+    static void check();
+};
+
+extern MarlinEthernet ethernet;