odroidxu4_defconfig enable lvm and dm-crypt #12

Dmole · 2016-10-05T16:04:36Z

Tested, and unlike hardkernel_3.10, tobetter_4.8 is stable under heavy load.

It's excessive to use prefix for the parameters when you do modprobe mmc-block mmcblk.perdev_minors=16 Make this available only for built-in case. Change-Id: I85b3ab146cca341795315fb5578fec8ceda3d30c Signed-off-by: Andy Shevchenko <[email protected]> Signed-off-by: Ulf Hansson <[email protected]>

Added .shutdown function to s2mps11 to help poweroff the board successfully. The device driver clears the register to turn off the PMIC. s2mps11-pmic: S2MPS11_REG_CTRL1 reg value 16:00000000000000000000000000010000 Console log. * Unmounting temporary filesystems... [ OK ] * Deactivating swap... [ OK ] * Unmounting local filesystems... [ OK ] * Will now halt [ 209.020280] reboot: Power down [ 209.122039] Power down failed, please power off system manually. Change-Id: If6ea0dec154b00ceeaaddbac393c67dc35c26279 Signed-off-by: Anand Moon <[email protected]>

Adding phy calibration sequence for USB 3.0 DRD PHY present on Exynos5420/5800 systems. This calibration facilitates setting certain PHY parameters viz. the Loss-of-Signal (LOS) Detector Threshold Level, as well as Tx-Vboost-Level for Super-Speed operations. Additionally we also set proper time to wait for RxDetect measurement, for desired PHY reference clock, so as to solve issue with enumeration of few USB 3.0 devices, like Samsung SUM-TSB16S 3.0 USB drive on the controller. We are using CR_port for this purpose to send required data to override the LOS values. On testing with USB 3.0 devices on USB 3.0 port present on SMDK5420, and peach-pit boards should see following message: usb 2-1: new SuperSpeed USB device number 2 using xhci-hcd and without this patch, should see below shown message: usb 1-1: new high-speed USB device number 2 using xhci-hcd [Also removed unnecessary extra lines in the register macro definitions] Change-Id: I81dcd0dfa057b6b63e18578f2bc9dc276cc5b74a Signed-off-by: Vivek Gautam <[email protected]>

This driver helps to register the device of GPIO based IR receiver, "gpio-ir-recv", with the gpio number and pulse trigger when driver is loading. For example, # modprobe gpio-ir-recv # modprobe gpioplug-ir-recv gpio_nr=24 active_low=1 Signed-off-by: Dongjin Kim <[email protected]>

This changes enables TMU IP block on the Exynos5422 Odroid-XU3 device. Signed-off-by: Anand Moon <[email protected]> Acked-by: Lukasz Majewski <[email protected]> Signed-off-by: Krzysztof Kozlowski <[email protected]>

Change-Id: I65e9f38395dddfbe14daf7300a34a955453b5cb4 Signed-off-by: Dongjin Kim <[email protected]>

Signed-off-by: Dongjin Kim <[email protected]>

Fixed the compilation warning. Change-Id: I4cab298773bd68eef9c1bc5972e23f627f5b691b

Change-Id: Ie2991f4d625c8e7bae9dcd07961fdb29bf6ebaff Signed-off-by: Dongjin Kim <[email protected]>

Added the missing freq changes for A15 and A7 Change-Id: I4f485d349393944cb8b5ae3f8177ef9c11e9290a Signed-off-by: Tom Briden <[email protected]>

Change-Id: Ic65075b3167ed99d2df1adaa2eb2df7e2b59360f

Added UHS-I bus speeds: SDR50 DDR50 SDR104 Change-Id: Iecbf6cea064b94edd71e3f60b35408ef75495815 Signed-off-by: Dongjin Kim <[email protected]>

https://patchwork.kernel.org/patch/5760901/ Subject: [V7,RESEND,1/2] usb: host: xhci-plat: Get PHYs for xhci's hcds The host controller by itself may sometimes need to handle PHY and re-initialize it to re-configure some of the PHY parameters to get full support out of the PHY controller. Therefore, facilitate getting the two possible PHYs, viz. USB 2.0 type (UTMI+) and USB 3.0 type (PIPE3), and initialize them. Change-Id: Ida45fe595eb6cd3501b9897aae1428ec23c10aa6 Signed-off-by: Vivek Gautam <[email protected]> Signed-off-by: Dongjin Kim <[email protected]>

Change-Id: Ie34ce98fbc8a86c840673b68bf20efe9846f5404 Signed-off-by: Dongjin Kim <[email protected]>

…xu4-v4.8

Dmole · 2016-10-06T14:01:08Z

Merged and tested kernel_4.8

commit 3a402a7 upstream. When TIF_SINGLESTEP is set for a task, the single-step state machine is enabled and we must take care not to reset it to the active-not-pending state if it is already in the active-pending state. Unfortunately, that's exactly what user_enable_single_step does, by unconditionally setting the SS bit in the SPSR for the current task. This causes failures in the GDB testsuite, where GDB ends up missing expected step traps if the instruction being stepped generates another trap, e.g. PTRACE_EVENT_FORK from an SVC instruction. This patch fixes the problem by preserving the current state of the stepping state machine when TIF_SINGLESTEP is set on the current thread. Cc: <[email protected]> Reported-by: Yao Qi <[email protected]> Signed-off-by: Will Deacon <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit 21f54dd upstream. That just generally kills the machine, and makes debugging only much harder, since the traces may long be gone. Debugging by assert() is a disease. Don't do it. If you can continue, you're much better off doing so with a live machine where you have a much higher chance that the report actually makes it to the system logs, rather than result in a machine that is just completely dead. The only valid situation for BUG_ON() is when continuing is not an option, because there is massive corruption. But if you are just verifying that something is true, you warn about your broken assumptions (preferably just once), and limp on. Fixes: 22f2ac5 ("mm: workingset: fix crash in shadow node shrinker caused by replace_page_cache_page()") Cc: Johannes Weiner <[email protected]> Cc: Miklos Szeredi <[email protected]> Cc: Andrew Morton <[email protected]> Signed-off-by: Linus Torvalds <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit 2fae9e5 upstream. This patch fixes a NULL pointer dereference caused by a race codition in the probe function of the legousbtower driver. It re-structures the probe function to only register the interface after successfully reading the board's firmware ID. The probe function does not deregister the usb interface after an error receiving the devices firmware ID. The device file registered (/dev/usb/legousbtower%d) may be read/written globally before the probe function returns. When tower_delete is called in the probe function (after an r/w has been initiated), core dev structures are deleted while the file operation functions are still running. If the 0 address is mappable on the machine, this vulnerability can be used to create a Local Priviege Escalation exploit via a write-what-where condition by remapping dev->interrupt_out_buffer in tower_write. A forged USB device and local program execution would be required for LPE. The USB device would have to delay the control message in tower_probe and accept the control urb in tower_open whilst guest code initiated a write to the device file as tower_delete is called from the error in tower_probe. This bug has existed since 2003. Patch tested by emulated device. Reported-by: James Patrick-Evans <[email protected]> Tested-by: James Patrick-Evans <[email protected]> Signed-off-by: James Patrick-Evans <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit fc1e2c8 upstream. Commit 367e856 introduced a bug in fbtft-core where fps is always 0, this is because variable update_time is not assigned correctly. Signed-off-by: Ksenija Stanojevic <[email protected]> Fixes: 367e856 ("Staging: fbtbt: Replace timespec with ktime_t") Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit 238b7bd upstream. In v_recv_cmd_submit(), urb_p->urb->pipe has the type unsigned int (which is 32-bit long on x86_64) but 11<<30 results in a 34-bit integer. Therefore the 2 leading bits are truncated and urb_p->urb->pipe &= ~(11 << 30); has the same meaning as urb_p->urb->pipe &= ~(3 << 30); This second statement seems to be how the code was intended to be written, as PIPE_ constants have values between 0 and 3. The overflow has been detected with a clang warning: drivers/usb/usbip/vudc_rx.c:145:27: warning: signed shift result (0x2C0000000) requires 35 bits to represent, but 'int' only has 32 bits [-Wshift-overflow] urb_p->urb->pipe &= ~(11 << 30); ~~ ^ ~~ Fixes: 79c02cb ("usbip: vudc: Add vudc_rx") Signed-off-by: Nicolas Iooss <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit decc536 upstream. Signed-off-by: Kyle Jones <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit ab21b63 upstream. This reverts commit e6c7efd. Turns out it was totally wrong. The memory is supposed to be bound to the kref, as the original code was doing correctly, not the device/driver binding as the devm_kzalloc() would cause. This fixes an oops when read would be called after the device was unbound from the driver. Reported-by: Ladislav Michl <[email protected]> Cc: Andy Shevchenko <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit 392c9da upstream. We have two new Dell laptop models, they have the same ALC255 pin definition, but not in the pin quirk table yet, as a result, the headset microphone can't work. After adding the definition in the table, the headset microphone works well. Signed-off-by: Hui Wang <[email protected]> Signed-off-by: Takashi Iwai <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit 3f64097 upstream. One of the laptops has the codec ALC256 on it, applying the ALC255_FIXUP_DELL1_MIC_NO_PRESENCE can fix the problem, the rest of laptops have the codec ALC295 on them, they are similar to machines with ALC225, applying the ALC269_FIXUP_DELL1_MIC_NO_PRESENCE can fix the problem. Signed-off-by: Hui Wang <[email protected]> Signed-off-by: Takashi Iwai <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit 0eec880 upstream. HP Spectre x360 with CX20724 codec has two speaker outputs while the BIOS sets up only the bottom one (NID 0x17) and disables the top one (NID 0x1d). This patch adds a fixup simply defining the proper pincfg for NID 0x1d so that the top speaker works as is. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=169071 Signed-off-by: Takashi Iwai <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

…xu4-v4.8

[ Upstream commit 24457f1 ] syzkaller reported a warning [0] triggered while destroying immature netns. rpc_proc_register() was called in init_nfs_fs(), but its error has been ignored since at least the initial commit 1da177e4c3f4 ("Linux-2.6.12-rc2"). Recently, commit d47151b ("nfs: expose /proc/net/sunrpc/nfs in net namespaces") converted the procfs to per-netns and made the problem more visible. Even when rpc_proc_register() fails, nfs_net_init() could succeed, and thus nfs_net_exit() will be called while destroying the netns. Then, remove_proc_entry() will be called for non-existing proc directory and trigger the warning below. Let's handle the error of rpc_proc_register() properly in nfs_net_init(). [0]: name 'nfs' WARNING: CPU: 1 PID: 1710 at fs/proc/generic.c:711 remove_proc_entry+0x1bb/0x2d0 fs/proc/generic.c:711 Modules linked in: CPU: 1 PID: 1710 Comm: syz-executor.2 Not tainted 6.8.0-12822-gcd51db110a7e #12 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/2014 RIP: 0010:remove_proc_entry+0x1bb/0x2d0 fs/proc/generic.c:711 Code: 41 5d 41 5e c3 e8 85 09 b5 ff 48 c7 c7 88 58 64 86 e8 09 0e 71 02 e8 74 09 b5 ff 4c 89 e6 48 c7 c7 de 1b 80 84 e8 c5 ad 97 ff <0f> 0b eb b1 e8 5c 09 b5 ff 48 c7 c7 88 58 64 86 e8 e0 0d 71 02 eb RSP: 0018:ffffc9000c6d7ce0 EFLAGS: 00010286 RAX: 0000000000000000 RBX: ffff8880422b8b00 RCX: ffffffff8110503c RDX: ffff888030652f00 RSI: ffffffff81105045 RDI: 0000000000000001 RBP: 0000000000000000 R08: 0000000000000001 R09: 0000000000000000 R10: 0000000000000001 R11: ffffffff81bb62cb R12: ffffffff84807ffc R13: ffff88804ad6fcc0 R14: ffffffff84807ffc R15: ffffffff85741ff8 FS: 00007f30cfba8640(0000) GS:ffff88807dd00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007ff51afe8000 CR3: 000000005a60a005 CR4: 0000000000770ef0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 PKRU: 55555554 Call Trace: <TASK> rpc_proc_unregister+0x64/0x70 net/sunrpc/stats.c:310 nfs_net_exit+0x1c/0x30 fs/nfs/inode.c:2438 ops_exit_list+0x62/0xb0 net/core/net_namespace.c:170 setup_net+0x46c/0x660 net/core/net_namespace.c:372 copy_net_ns+0x244/0x590 net/core/net_namespace.c:505 create_new_namespaces+0x2ed/0x770 kernel/nsproxy.c:110 unshare_nsproxy_namespaces+0xae/0x160 kernel/nsproxy.c:228 ksys_unshare+0x342/0x760 kernel/fork.c:3322 __do_sys_unshare kernel/fork.c:3393 [inline] __se_sys_unshare kernel/fork.c:3391 [inline] __x64_sys_unshare+0x1f/0x30 kernel/fork.c:3391 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0x4f/0x110 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x46/0x4e RIP: 0033:0x7f30d0febe5d Code: ff c3 66 2e 0f 1f 84 00 00 00 00 00 90 f3 0f 1e fa 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 73 9f 1b 00 f7 d8 64 89 01 48 RSP: 002b:00007f30cfba7cc8 EFLAGS: 00000246 ORIG_RAX: 0000000000000110 RAX: ffffffffffffffda RBX: 00000000004bbf80 RCX: 00007f30d0febe5d RDX: 0000000000000000 RSI: 0000000000000000 RDI: 000000006c020600 RBP: 00000000004bbf80 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000002 R13: 000000000000000b R14: 00007f30d104c530 R15: 0000000000000000 </TASK> Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Reported-by: syzkaller <[email protected]> Signed-off-by: Kuniyuki Iwashima <[email protected]> Signed-off-by: Trond Myklebust <[email protected]> Signed-off-by: Sasha Levin <[email protected]>

[ Upstream commit 8e088a2 ] Commit 1548036 ("nfs: make the rpc_stat per net namespace") added functionality to specify rpc_stats function but missed adding it to the TCP TLS functionality. As the result, mounting with xprtsec=tls lead to the following kernel oops. [ 128.984192] Unable to handle kernel NULL pointer dereference at virtual address 000000000000001c [ 128.985058] Mem abort info: [ 128.985372] ESR = 0x0000000096000004 [ 128.985709] EC = 0x25: DABT (current EL), IL = 32 bits [ 128.986176] SET = 0, FnV = 0 [ 128.986521] EA = 0, S1PTW = 0 [ 128.986804] FSC = 0x04: level 0 translation fault [ 128.987229] Data abort info: [ 128.987597] ISV = 0, ISS = 0x00000004, ISS2 = 0x00000000 [ 128.988169] CM = 0, WnR = 0, TnD = 0, TagAccess = 0 [ 128.988811] GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0 [ 128.989302] user pgtable: 4k pages, 48-bit VAs, pgdp=0000000106c84000 [ 128.990048] [000000000000001c] pgd=0000000000000000, p4d=0000000000000000 [ 128.990736] Internal error: Oops: 0000000096000004 [#1] SMP [ 128.991168] Modules linked in: nfs_layout_nfsv41_files rpcsec_gss_krb5 auth_rpcgss nfsv4 dns_resolver nfs lockd grace netfs uinput dm_mod nft_fib_inet nft_fib_ipv4 nft_fib_ipv6 nft_fib nft_reject_inet nf_reject_ipv4 nf_reject_ipv6 nft_reject nft_ct nft_chain_nat nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 rfkill ip_set nf_tables nfnetlink qrtr vsock_loopback vmw_vsock_virtio_transport_common vmw_vsock_vmci_transport vsock sunrpc vfat fat uvcvideo videobuf2_vmalloc videobuf2_memops uvc videobuf2_v4l2 videodev videobuf2_common mc vmw_vmci xfs libcrc32c e1000e crct10dif_ce ghash_ce sha2_ce vmwgfx nvme sha256_arm64 nvme_core sr_mod cdrom sha1_ce drm_ttm_helper ttm drm_kms_helper drm sg fuse [ 128.996466] CPU: 0 PID: 179 Comm: kworker/u4:26 Kdump: loaded Not tainted 6.8.0-rc6+ #12 [ 128.997226] Hardware name: VMware, Inc. VMware20,1/VBSA, BIOS VMW201.00V.21805430.BA64.2305221830 05/22/2023 [ 128.998084] Workqueue: xprtiod xs_tcp_tls_setup_socket [sunrpc] [ 128.998701] pstate: 81400005 (Nzcv daif +PAN -UAO -TCO +DIT -SSBS BTYPE=--) [ 128.999384] pc : call_start+0x74/0x138 [sunrpc] [ 128.999809] lr : __rpc_execute+0xb8/0x3e0 [sunrpc] [ 129.000244] sp : ffff8000832b3a00 [ 129.000508] x29: ffff8000832b3a00 x28: ffff800081ac79c0 x27: ffff800081ac7000 [ 129.001111] x26: 0000000004248060 x25: 0000000000000000 x24: ffff800081596008 [ 129.001757] x23: ffff80007b087240 x22: ffff00009a509d30 x21: 0000000000000000 [ 129.002345] x20: ffff000090075600 x19: ffff00009a509d00 x18: ffffffffffffffff [ 129.002912] x17: 733d4d4554535953 x16: 42555300312d746e x15: ffff8000832b3a88 [ 129.003464] x14: ffffffffffffffff x13: ffff8000832b3a7d x12: 0000000000000008 [ 129.004021] x11: 0101010101010101 x10: ffff8000150cb560 x9 : ffff80007b087c00 [ 129.004577] x8 : ffff00009a509de0 x7 : 0000000000000000 x6 : 00000000be8c4ee3 [ 129.005026] x5 : 0000000000000000 x4 : 0000000000000000 x3 : ffff000094d56680 [ 129.005425] x2 : ffff80007b0637f8 x1 : ffff000090075600 x0 : ffff00009a509d00 [ 129.005824] Call trace: [ 129.005967] call_start+0x74/0x138 [sunrpc] [ 129.006233] __rpc_execute+0xb8/0x3e0 [sunrpc] [ 129.006506] rpc_execute+0x160/0x1d8 [sunrpc] [ 129.006778] rpc_run_task+0x148/0x1f8 [sunrpc] [ 129.007204] tls_probe+0x80/0xd0 [sunrpc] [ 129.007460] rpc_ping+0x28/0x80 [sunrpc] [ 129.007715] rpc_create_xprt+0x134/0x1a0 [sunrpc] [ 129.007999] rpc_create+0x128/0x2a0 [sunrpc] [ 129.008264] xs_tcp_tls_setup_socket+0xdc/0x508 [sunrpc] [ 129.008583] process_one_work+0x174/0x3c8 [ 129.008813] worker_thread+0x2c8/0x3e0 [ 129.009033] kthread+0x100/0x110 [ 129.009225] ret_from_fork+0x10/0x20 [ 129.009432] Code: f0ffffc2 911fe042 aa1403e1 aa1303e0 (b9401c83) Fixes: 1548036 ("nfs: make the rpc_stat per net namespace") Signed-off-by: Olga Kornievskaia <[email protected]> Signed-off-by: Trond Myklebust <[email protected]> Signed-off-by: Sasha Levin <[email protected]>

[ Upstream commit 769e6a1 ] ui_browser__show() is capturing the input title that is stack allocated memory in hist_browser__run(). Avoid a use after return by strdup-ing the string. Committer notes: Further explanation from Ian Rogers: My command line using tui is: $ sudo bash -c 'rm /tmp/asan.log*; export ASAN_OPTIONS="log_path=/tmp/asan.log"; /tmp/perf/perf mem record -a sleep 1; /tmp/perf/perf mem report' I then go to the perf annotate view and quit. This triggers the asan error (from the log file): ``` ==1254591==ERROR: AddressSanitizer: stack-use-after-return on address 0x7f2813331920 at pc 0x7f28180 65991 bp 0x7fff0a21c750 sp 0x7fff0a21bf10 READ of size 80 at 0x7f2813331920 thread T0 #0 0x7f2818065990 in __interceptor_strlen ../../../../src/libsanitizer/sanitizer_common/sanitizer_common_interceptors.inc:461 #1 0x7f2817698251 in SLsmg_write_wrapped_string (/lib/x86_64-linux-gnu/libslang.so.2+0x98251) #2 0x7f28176984b9 in SLsmg_write_nstring (/lib/x86_64-linux-gnu/libslang.so.2+0x984b9) #3 0x55c94045b365 in ui_browser__write_nstring ui/browser.c:60 #4 0x55c94045c558 in __ui_browser__show_title ui/browser.c:266 #5 0x55c94045c776 in ui_browser__show ui/browser.c:288 #6 0x55c94045c06d in ui_browser__handle_resize ui/browser.c:206 #7 0x55c94047979b in do_annotate ui/browsers/hists.c:2458 #8 0x55c94047fb17 in evsel__hists_browse ui/browsers/hists.c:3412 #9 0x55c940480a0c in perf_evsel_menu__run ui/browsers/hists.c:3527 #10 0x55c940481108 in __evlist__tui_browse_hists ui/browsers/hists.c:3613 #11 0x55c9404813f7 in evlist__tui_browse_hists ui/browsers/hists.c:3661 #12 0x55c93ffa253f in report__browse_hists tools/perf/builtin-report.c:671 #13 0x55c93ffa58ca in __cmd_report tools/perf/builtin-report.c:1141 #14 0x55c93ffaf159 in cmd_report tools/perf/builtin-report.c:1805 #15 0x55c94000c05c in report_events tools/perf/builtin-mem.c:374 #16 0x55c94000d96d in cmd_mem tools/perf/builtin-mem.c:516 #17 0x55c9400e44ee in run_builtin tools/perf/perf.c:350 #18 0x55c9400e4a5a in handle_internal_command tools/perf/perf.c:403 #19 0x55c9400e4e22 in run_argv tools/perf/perf.c:447 #20 0x55c9400e53ad in main tools/perf/perf.c:561 #21 0x7f28170456c9 in __libc_start_call_main ../sysdeps/nptl/libc_start_call_main.h:58 #22 0x7f2817045784 in __libc_start_main_impl ../csu/libc-start.c:360 #23 0x55c93ff544c0 in _start (/tmp/perf/perf+0x19a4c0) (BuildId: 84899b0e8c7d3a3eaa67b2eb35e3d8b2f8cd4c93) Address 0x7f2813331920 is located in stack of thread T0 at offset 32 in frame #0 0x55c94046e85e in hist_browser__run ui/browsers/hists.c:746 This frame has 1 object(s): [32, 192) 'title' (line 747) <== Memory access at offset 32 is inside this variable HINT: this may be a false positive if your program uses some custom stack unwind mechanism, swapcontext or vfork ``` hist_browser__run isn't on the stack so the asan error looks legit. There's no clean init/exit on struct ui_browser so I may be trading a use-after-return for a memory leak, but that seems look a good trade anyway. Fixes: 05e8b08 ("perf ui browser: Stop using 'self'") Signed-off-by: Ian Rogers <[email protected]> Cc: Adrian Hunter <[email protected]> Cc: Alexander Shishkin <[email protected]> Cc: Andi Kleen <[email protected]> Cc: Athira Rajeev <[email protected]> Cc: Ben Gainey <[email protected]> Cc: Ingo Molnar <[email protected]> Cc: James Clark <[email protected]> Cc: Jiri Olsa <[email protected]> Cc: Kajol Jain <[email protected]> Cc: Kan Liang <[email protected]> Cc: K Prateek Nayak <[email protected]> Cc: Li Dong <[email protected]> Cc: Mark Rutland <[email protected]> Cc: Namhyung Kim <[email protected]> Cc: Oliver Upton <[email protected]> Cc: Paran Lee <[email protected]> Cc: Peter Zijlstra <[email protected]> Cc: Ravi Bangoria <[email protected]> Cc: Sun Haiyong <[email protected]> Cc: Tim Chen <[email protected]> Cc: Yanteng Si <[email protected]> Cc: Yicong Yang <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Arnaldo Carvalho de Melo <[email protected]> Signed-off-by: Sasha Levin <[email protected]>

[ Upstream commit 51d1b25 ] syzkaller reported data-race of sk->sk_hash in unix_autobind() [0], and the same ones exist in unix_bind_bsd() and unix_bind_abstract(). The three bind() functions prefetch sk->sk_hash locklessly and use it later after validating that unix_sk(sk)->addr is NULL under unix_sk(sk)->bindlock. The prefetched sk->sk_hash is the hash value of unbound socket set in unix_create1() and does not change until bind() completes. There could be a chance that sk->sk_hash changes after the lockless read. However, in such a case, non-NULL unix_sk(sk)->addr is visible under unix_sk(sk)->bindlock, and bind() returns -EINVAL without using the prefetched value. The KCSAN splat is false-positive, but let's silence it by reading sk->sk_hash under unix_sk(sk)->bindlock. [0]: BUG: KCSAN: data-race in unix_autobind / unix_autobind write to 0xffff888034a9fb88 of 4 bytes by task 4468 on cpu 0: __unix_set_addr_hash net/unix/af_unix.c:331 [inline] unix_autobind+0x47a/0x7d0 net/unix/af_unix.c:1185 unix_dgram_connect+0x7e3/0x890 net/unix/af_unix.c:1373 __sys_connect_file+0xd7/0xe0 net/socket.c:2048 __sys_connect+0x114/0x140 net/socket.c:2065 __do_sys_connect net/socket.c:2075 [inline] __se_sys_connect net/socket.c:2072 [inline] __x64_sys_connect+0x40/0x50 net/socket.c:2072 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0x4f/0x110 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x46/0x4e read to 0xffff888034a9fb88 of 4 bytes by task 4465 on cpu 1: unix_autobind+0x28/0x7d0 net/unix/af_unix.c:1134 unix_dgram_connect+0x7e3/0x890 net/unix/af_unix.c:1373 __sys_connect_file+0xd7/0xe0 net/socket.c:2048 __sys_connect+0x114/0x140 net/socket.c:2065 __do_sys_connect net/socket.c:2075 [inline] __se_sys_connect net/socket.c:2072 [inline] __x64_sys_connect+0x40/0x50 net/socket.c:2072 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0x4f/0x110 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x46/0x4e value changed: 0x000000e4 -> 0x000001e3 Reported by Kernel Concurrency Sanitizer on: CPU: 1 PID: 4465 Comm: syz-executor.0 Not tainted 6.8.0-12822-gcd51db110a7e #12 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/2014 Fixes: afd20b9 ("af_unix: Replace the big lock with small locks.") Reported-by: syzkaller <[email protected]> Signed-off-by: Kuniyuki Iwashima <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Paolo Abeni <[email protected]> Signed-off-by: Sasha Levin <[email protected]>

commit 9d274c1 upstream. We have been seeing crashes on duplicate keys in btrfs_set_item_key_safe(): BTRFS critical (device vdb): slot 4 key (450 108 8192) new key (450 108 8192) ------------[ cut here ]------------ kernel BUG at fs/btrfs/ctree.c:2620! invalid opcode: 0000 [#1] PREEMPT SMP PTI CPU: 0 PID: 3139 Comm: xfs_io Kdump: loaded Not tainted 6.9.0 #6 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.3-2.fc40 04/01/2014 RIP: 0010:btrfs_set_item_key_safe+0x11f/0x290 [btrfs] With the following stack trace: #0 btrfs_set_item_key_safe (fs/btrfs/ctree.c:2620:4) #1 btrfs_drop_extents (fs/btrfs/file.c:411:4) #2 log_one_extent (fs/btrfs/tree-log.c:4732:9) #3 btrfs_log_changed_extents (fs/btrfs/tree-log.c:4955:9) #4 btrfs_log_inode (fs/btrfs/tree-log.c:6626:9) #5 btrfs_log_inode_parent (fs/btrfs/tree-log.c:7070:8) #6 btrfs_log_dentry_safe (fs/btrfs/tree-log.c:7171:8) #7 btrfs_sync_file (fs/btrfs/file.c:1933:8) #8 vfs_fsync_range (fs/sync.c:188:9) #9 vfs_fsync (fs/sync.c:202:9) #10 do_fsync (fs/sync.c:212:9) #11 __do_sys_fdatasync (fs/sync.c:225:9) #12 __se_sys_fdatasync (fs/sync.c:223:1) #13 __x64_sys_fdatasync (fs/sync.c:223:1) #14 do_syscall_x64 (arch/x86/entry/common.c:52:14) #15 do_syscall_64 (arch/x86/entry/common.c:83:7) #16 entry_SYSCALL_64+0xaf/0x14c (arch/x86/entry/entry_64.S:121) So we're logging a changed extent from fsync, which is splitting an extent in the log tree. But this split part already exists in the tree, triggering the BUG(). This is the state of the log tree at the time of the crash, dumped with drgn (https://github.com/osandov/drgn/blob/main/contrib/btrfs_tree.py) to get more details than btrfs_print_leaf() gives us: >>> print_extent_buffer(prog.crashed_thread().stack_trace()[0]["eb"]) leaf 33439744 level 0 items 72 generation 9 owner 18446744073709551610 leaf 33439744 flags 0x100000000000000 fs uuid e5bd3946-400c-4223-8923-190ef1f18677 chunk uuid d58cb17e-6d02-494a-829a-18b7d8a399da item 0 key (450 INODE_ITEM 0) itemoff 16123 itemsize 160 generation 7 transid 9 size 8192 nbytes 8473563889606862198 block group 0 mode 100600 links 1 uid 0 gid 0 rdev 0 sequence 204 flags 0x10(PREALLOC) atime 1716417703.220000000 (2024-05-22 15:41:43) ctime 1716417704.983333333 (2024-05-22 15:41:44) mtime 1716417704.983333333 (2024-05-22 15:41:44) otime 17592186044416.000000000 (559444-03-08 01:40:16) item 1 key (450 INODE_REF 256) itemoff 16110 itemsize 13 index 195 namelen 3 name: 193 item 2 key (450 XATTR_ITEM 1640047104) itemoff 16073 itemsize 37 location key (0 UNKNOWN.0 0) type XATTR transid 7 data_len 1 name_len 6 name: user.a data a item 3 key (450 EXTENT_DATA 0) itemoff 16020 itemsize 53 generation 9 type 1 (regular) extent data disk byte 303144960 nr 12288 extent data offset 0 nr 4096 ram 12288 extent compression 0 (none) item 4 key (450 EXTENT_DATA 4096) itemoff 15967 itemsize 53 generation 9 type 2 (prealloc) prealloc data disk byte 303144960 nr 12288 prealloc data offset 4096 nr 8192 item 5 key (450 EXTENT_DATA 8192) itemoff 15914 itemsize 53 generation 9 type 2 (prealloc) prealloc data disk byte 303144960 nr 12288 prealloc data offset 8192 nr 4096 ... So the real problem happened earlier: notice that items 4 (4k-12k) and 5 (8k-12k) overlap. Both are prealloc extents. Item 4 straddles i_size and item 5 starts at i_size. Here is the state of the filesystem tree at the time of the crash: >>> root = prog.crashed_thread().stack_trace()[2]["inode"].root >>> ret, nodes, slots = btrfs_search_slot(root, BtrfsKey(450, 0, 0)) >>> print_extent_buffer(nodes[0]) leaf 30425088 level 0 items 184 generation 9 owner 5 leaf 30425088 flags 0x100000000000000 fs uuid e5bd3946-400c-4223-8923-190ef1f18677 chunk uuid d58cb17e-6d02-494a-829a-18b7d8a399da ... item 179 key (450 INODE_ITEM 0) itemoff 4907 itemsize 160 generation 7 transid 7 size 4096 nbytes 12288 block group 0 mode 100600 links 1 uid 0 gid 0 rdev 0 sequence 6 flags 0x10(PREALLOC) atime 1716417703.220000000 (2024-05-22 15:41:43) ctime 1716417703.220000000 (2024-05-22 15:41:43) mtime 1716417703.220000000 (2024-05-22 15:41:43) otime 1716417703.220000000 (2024-05-22 15:41:43) item 180 key (450 INODE_REF 256) itemoff 4894 itemsize 13 index 195 namelen 3 name: 193 item 181 key (450 XATTR_ITEM 1640047104) itemoff 4857 itemsize 37 location key (0 UNKNOWN.0 0) type XATTR transid 7 data_len 1 name_len 6 name: user.a data a item 182 key (450 EXTENT_DATA 0) itemoff 4804 itemsize 53 generation 9 type 1 (regular) extent data disk byte 303144960 nr 12288 extent data offset 0 nr 8192 ram 12288 extent compression 0 (none) item 183 key (450 EXTENT_DATA 8192) itemoff 4751 itemsize 53 generation 9 type 2 (prealloc) prealloc data disk byte 303144960 nr 12288 prealloc data offset 8192 nr 4096 Item 5 in the log tree corresponds to item 183 in the filesystem tree, but nothing matches item 4. Furthermore, item 183 is the last item in the leaf. btrfs_log_prealloc_extents() is responsible for logging prealloc extents beyond i_size. It first truncates any previously logged prealloc extents that start beyond i_size. Then, it walks the filesystem tree and copies the prealloc extent items to the log tree. If it hits the end of a leaf, then it calls btrfs_next_leaf(), which unlocks the tree and does another search. However, while the filesystem tree is unlocked, an ordered extent completion may modify the tree. In particular, it may insert an extent item that overlaps with an extent item that was already copied to the log tree. This may manifest in several ways depending on the exact scenario, including an EEXIST error that is silently translated to a full sync, overlapping items in the log tree, or this crash. This particular crash is triggered by the following sequence of events: - Initially, the file has i_size=4k, a regular extent from 0-4k, and a prealloc extent beyond i_size from 4k-12k. The prealloc extent item is the last item in its B-tree leaf. - The file is fsync'd, which copies its inode item and both extent items to the log tree. - An xattr is set on the file, which sets the BTRFS_INODE_COPY_EVERYTHING flag. - The range 4k-8k in the file is written using direct I/O. i_size is extended to 8k, but the ordered extent is still in flight. - The file is fsync'd. Since BTRFS_INODE_COPY_EVERYTHING is set, this calls copy_inode_items_to_log(), which calls btrfs_log_prealloc_extents(). - btrfs_log_prealloc_extents() finds the 4k-12k prealloc extent in the filesystem tree. Since it starts before i_size, it skips it. Since it is the last item in its B-tree leaf, it calls btrfs_next_leaf(). - btrfs_next_leaf() unlocks the path. - The ordered extent completion runs, which converts the 4k-8k part of the prealloc extent to written and inserts the remaining prealloc part from 8k-12k. - btrfs_next_leaf() does a search and finds the new prealloc extent 8k-12k. - btrfs_log_prealloc_extents() copies the 8k-12k prealloc extent into the log tree. Note that it overlaps with the 4k-12k prealloc extent that was copied to the log tree by the first fsync. - fsync calls btrfs_log_changed_extents(), which tries to log the 4k-8k extent that was written. - This tries to drop the range 4k-8k in the log tree, which requires adjusting the start of the 4k-12k prealloc extent in the log tree to 8k. - btrfs_set_item_key_safe() sees that there is already an extent starting at 8k in the log tree and calls BUG(). Fix this by detecting when we're about to insert an overlapping file extent item in the log tree and truncating the part that would overlap. CC: [email protected] # 6.1+ Reviewed-by: Filipe Manana <[email protected]> Signed-off-by: Omar Sandoval <[email protected]> Signed-off-by: David Sterba <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit be346c1 upstream. The code in ocfs2_dio_end_io_write() estimates number of necessary transaction credits using ocfs2_calc_extend_credits(). This however does not take into account that the IO could be arbitrarily large and can contain arbitrary number of extents. Extent tree manipulations do often extend the current transaction but not in all of the cases. For example if we have only single block extents in the tree, ocfs2_mark_extent_written() will end up calling ocfs2_replace_extent_rec() all the time and we will never extend the current transaction and eventually exhaust all the transaction credits if the IO contains many single block extents. Once that happens a WARN_ON(jbd2_handle_buffer_credits(handle) <= 0) is triggered in jbd2_journal_dirty_metadata() and subsequently OCFS2 aborts in response to this error. This was actually triggered by one of our customers on a heavily fragmented OCFS2 filesystem. To fix the issue make sure the transaction always has enough credits for one extent insert before each call of ocfs2_mark_extent_written(). Heming Zhao said: ------ PANIC: "Kernel panic - not syncing: OCFS2: (device dm-1): panic forced after error" PID: xxx TASK: xxxx CPU: 5 COMMAND: "SubmitThread-CA" #0 machine_kexec at ffffffff8c069932 #1 __crash_kexec at ffffffff8c1338fa #2 panic at ffffffff8c1d69b9 #3 ocfs2_handle_error at ffffffffc0c86c0c [ocfs2] #4 __ocfs2_abort at ffffffffc0c88387 [ocfs2] #5 ocfs2_journal_dirty at ffffffffc0c51e98 [ocfs2] #6 ocfs2_split_extent at ffffffffc0c27ea3 [ocfs2] #7 ocfs2_change_extent_flag at ffffffffc0c28053 [ocfs2] #8 ocfs2_mark_extent_written at ffffffffc0c28347 [ocfs2] #9 ocfs2_dio_end_io_write at ffffffffc0c2bef9 [ocfs2] #10 ocfs2_dio_end_io at ffffffffc0c2c0f5 [ocfs2] #11 dio_complete at ffffffff8c2b9fa7 #12 do_blockdev_direct_IO at ffffffff8c2bc09f #13 ocfs2_direct_IO at ffffffffc0c2b653 [ocfs2] #14 generic_file_direct_write at ffffffff8c1dcf14 #15 __generic_file_write_iter at ffffffff8c1dd07b #16 ocfs2_file_write_iter at ffffffffc0c49f1f [ocfs2] #17 aio_write at ffffffff8c2cc72e #18 kmem_cache_alloc at ffffffff8c248dde #19 do_io_submit at ffffffff8c2ccada #20 do_syscall_64 at ffffffff8c004984 #21 entry_SYSCALL_64_after_hwframe at ffffffff8c8000ba Link: https://lkml.kernel.org/r/[email protected] Link: https://lkml.kernel.org/r/[email protected] Fixes: c15471f ("ocfs2: fix sparse file & data ordering issue in direct io") Signed-off-by: Jan Kara <[email protected]> Reviewed-by: Joseph Qi <[email protected]> Reviewed-by: Heming Zhao <[email protected]> Cc: Mark Fasheh <[email protected]> Cc: Joel Becker <[email protected]> Cc: Junxiao Bi <[email protected]> Cc: Changwei Ge <[email protected]> Cc: Gang He <[email protected]> Cc: Jun Piao <[email protected]> Cc: <[email protected]> Signed-off-by: Andrew Morton <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

[ Upstream commit 97e1db0 ] Once unix_sk(sk)->addr is assigned under net->unx.table.locks and unix_sk(sk)->bindlock, *(unix_sk(sk)->addr) and unix_sk(sk)->path are fully set up, and unix_sk(sk)->addr is never changed. unix_getname() and unix_copy_addr() access the two fields locklessly, and commit ae3b564 ("missing barriers in some of unix_sock ->addr and ->path accesses") added smp_store_release() and smp_load_acquire() pairs. In other functions, we still read unix_sk(sk)->addr locklessly to check if the socket is bound, and KCSAN complains about it. [0] Given these functions have no dependency for *(unix_sk(sk)->addr) and unix_sk(sk)->path, READ_ONCE() is enough to annotate the data-race. Note that it is safe to access unix_sk(sk)->addr locklessly if the socket is found in the hash table. For example, the lockless read of otheru->addr in unix_stream_connect() is safe. Note also that newu->addr there is of the child socket that is still not accessible from userspace, and smp_store_release() publishes the address in case the socket is accept()ed and unix_getname() / unix_copy_addr() is called. [0]: BUG: KCSAN: data-race in unix_bind / unix_listen write (marked) to 0xffff88805f8d1840 of 8 bytes by task 13723 on cpu 0: __unix_set_addr_hash net/unix/af_unix.c:329 [inline] unix_bind_bsd net/unix/af_unix.c:1241 [inline] unix_bind+0x881/0x1000 net/unix/af_unix.c:1319 __sys_bind+0x194/0x1e0 net/socket.c:1847 __do_sys_bind net/socket.c:1858 [inline] __se_sys_bind net/socket.c:1856 [inline] __x64_sys_bind+0x40/0x50 net/socket.c:1856 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0x4f/0x110 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x46/0x4e read to 0xffff88805f8d1840 of 8 bytes by task 13724 on cpu 1: unix_listen+0x72/0x180 net/unix/af_unix.c:734 __sys_listen+0xdc/0x160 net/socket.c:1881 __do_sys_listen net/socket.c:1890 [inline] __se_sys_listen net/socket.c:1888 [inline] __x64_sys_listen+0x2e/0x40 net/socket.c:1888 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0x4f/0x110 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x46/0x4e value changed: 0x0000000000000000 -> 0xffff88807b5b1b40 Reported by Kernel Concurrency Sanitizer on: CPU: 1 PID: 13724 Comm: syz-executor.4 Not tainted 6.8.0-12822-gcd51db110a7e #12 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/2014 Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Reported-by: syzkaller <[email protected]> Signed-off-by: Kuniyuki Iwashima <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Paolo Abeni <[email protected]> Signed-off-by: Sasha Levin <[email protected]>

[ Upstream commit 51d1b25 ] syzkaller reported data-race of sk->sk_hash in unix_autobind() [0], and the same ones exist in unix_bind_bsd() and unix_bind_abstract(). The three bind() functions prefetch sk->sk_hash locklessly and use it later after validating that unix_sk(sk)->addr is NULL under unix_sk(sk)->bindlock. The prefetched sk->sk_hash is the hash value of unbound socket set in unix_create1() and does not change until bind() completes. There could be a chance that sk->sk_hash changes after the lockless read. However, in such a case, non-NULL unix_sk(sk)->addr is visible under unix_sk(sk)->bindlock, and bind() returns -EINVAL without using the prefetched value. The KCSAN splat is false-positive, but let's silence it by reading sk->sk_hash under unix_sk(sk)->bindlock. [0]: BUG: KCSAN: data-race in unix_autobind / unix_autobind write to 0xffff888034a9fb88 of 4 bytes by task 4468 on cpu 0: __unix_set_addr_hash net/unix/af_unix.c:331 [inline] unix_autobind+0x47a/0x7d0 net/unix/af_unix.c:1185 unix_dgram_connect+0x7e3/0x890 net/unix/af_unix.c:1373 __sys_connect_file+0xd7/0xe0 net/socket.c:2048 __sys_connect+0x114/0x140 net/socket.c:2065 __do_sys_connect net/socket.c:2075 [inline] __se_sys_connect net/socket.c:2072 [inline] __x64_sys_connect+0x40/0x50 net/socket.c:2072 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0x4f/0x110 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x46/0x4e read to 0xffff888034a9fb88 of 4 bytes by task 4465 on cpu 1: unix_autobind+0x28/0x7d0 net/unix/af_unix.c:1134 unix_dgram_connect+0x7e3/0x890 net/unix/af_unix.c:1373 __sys_connect_file+0xd7/0xe0 net/socket.c:2048 __sys_connect+0x114/0x140 net/socket.c:2065 __do_sys_connect net/socket.c:2075 [inline] __se_sys_connect net/socket.c:2072 [inline] __x64_sys_connect+0x40/0x50 net/socket.c:2072 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0x4f/0x110 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x46/0x4e value changed: 0x000000e4 -> 0x000001e3 Reported by Kernel Concurrency Sanitizer on: CPU: 1 PID: 4465 Comm: syz-executor.0 Not tainted 6.8.0-12822-gcd51db110a7e #12 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/2014 Fixes: afd20b9 ("af_unix: Replace the big lock with small locks.") Reported-by: syzkaller <[email protected]> Signed-off-by: Kuniyuki Iwashima <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Paolo Abeni <[email protected]> Signed-off-by: Sasha Levin <[email protected]>

commit 9d274c1 upstream. We have been seeing crashes on duplicate keys in btrfs_set_item_key_safe(): BTRFS critical (device vdb): slot 4 key (450 108 8192) new key (450 108 8192) ------------[ cut here ]------------ kernel BUG at fs/btrfs/ctree.c:2620! invalid opcode: 0000 [#1] PREEMPT SMP PTI CPU: 0 PID: 3139 Comm: xfs_io Kdump: loaded Not tainted 6.9.0 #6 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.3-2.fc40 04/01/2014 RIP: 0010:btrfs_set_item_key_safe+0x11f/0x290 [btrfs] With the following stack trace: #0 btrfs_set_item_key_safe (fs/btrfs/ctree.c:2620:4) #1 btrfs_drop_extents (fs/btrfs/file.c:411:4) #2 log_one_extent (fs/btrfs/tree-log.c:4732:9) #3 btrfs_log_changed_extents (fs/btrfs/tree-log.c:4955:9) #4 btrfs_log_inode (fs/btrfs/tree-log.c:6626:9) #5 btrfs_log_inode_parent (fs/btrfs/tree-log.c:7070:8) #6 btrfs_log_dentry_safe (fs/btrfs/tree-log.c:7171:8) #7 btrfs_sync_file (fs/btrfs/file.c:1933:8) #8 vfs_fsync_range (fs/sync.c:188:9) #9 vfs_fsync (fs/sync.c:202:9) #10 do_fsync (fs/sync.c:212:9) #11 __do_sys_fdatasync (fs/sync.c:225:9) #12 __se_sys_fdatasync (fs/sync.c:223:1) #13 __x64_sys_fdatasync (fs/sync.c:223:1) #14 do_syscall_x64 (arch/x86/entry/common.c:52:14) #15 do_syscall_64 (arch/x86/entry/common.c:83:7) #16 entry_SYSCALL_64+0xaf/0x14c (arch/x86/entry/entry_64.S:121) So we're logging a changed extent from fsync, which is splitting an extent in the log tree. But this split part already exists in the tree, triggering the BUG(). This is the state of the log tree at the time of the crash, dumped with drgn (https://github.com/osandov/drgn/blob/main/contrib/btrfs_tree.py) to get more details than btrfs_print_leaf() gives us: >>> print_extent_buffer(prog.crashed_thread().stack_trace()[0]["eb"]) leaf 33439744 level 0 items 72 generation 9 owner 18446744073709551610 leaf 33439744 flags 0x100000000000000 fs uuid e5bd3946-400c-4223-8923-190ef1f18677 chunk uuid d58cb17e-6d02-494a-829a-18b7d8a399da item 0 key (450 INODE_ITEM 0) itemoff 16123 itemsize 160 generation 7 transid 9 size 8192 nbytes 8473563889606862198 block group 0 mode 100600 links 1 uid 0 gid 0 rdev 0 sequence 204 flags 0x10(PREALLOC) atime 1716417703.220000000 (2024-05-22 15:41:43) ctime 1716417704.983333333 (2024-05-22 15:41:44) mtime 1716417704.983333333 (2024-05-22 15:41:44) otime 17592186044416.000000000 (559444-03-08 01:40:16) item 1 key (450 INODE_REF 256) itemoff 16110 itemsize 13 index 195 namelen 3 name: 193 item 2 key (450 XATTR_ITEM 1640047104) itemoff 16073 itemsize 37 location key (0 UNKNOWN.0 0) type XATTR transid 7 data_len 1 name_len 6 name: user.a data a item 3 key (450 EXTENT_DATA 0) itemoff 16020 itemsize 53 generation 9 type 1 (regular) extent data disk byte 303144960 nr 12288 extent data offset 0 nr 4096 ram 12288 extent compression 0 (none) item 4 key (450 EXTENT_DATA 4096) itemoff 15967 itemsize 53 generation 9 type 2 (prealloc) prealloc data disk byte 303144960 nr 12288 prealloc data offset 4096 nr 8192 item 5 key (450 EXTENT_DATA 8192) itemoff 15914 itemsize 53 generation 9 type 2 (prealloc) prealloc data disk byte 303144960 nr 12288 prealloc data offset 8192 nr 4096 ... So the real problem happened earlier: notice that items 4 (4k-12k) and 5 (8k-12k) overlap. Both are prealloc extents. Item 4 straddles i_size and item 5 starts at i_size. Here is the state of the filesystem tree at the time of the crash: >>> root = prog.crashed_thread().stack_trace()[2]["inode"].root >>> ret, nodes, slots = btrfs_search_slot(root, BtrfsKey(450, 0, 0)) >>> print_extent_buffer(nodes[0]) leaf 30425088 level 0 items 184 generation 9 owner 5 leaf 30425088 flags 0x100000000000000 fs uuid e5bd3946-400c-4223-8923-190ef1f18677 chunk uuid d58cb17e-6d02-494a-829a-18b7d8a399da ... item 179 key (450 INODE_ITEM 0) itemoff 4907 itemsize 160 generation 7 transid 7 size 4096 nbytes 12288 block group 0 mode 100600 links 1 uid 0 gid 0 rdev 0 sequence 6 flags 0x10(PREALLOC) atime 1716417703.220000000 (2024-05-22 15:41:43) ctime 1716417703.220000000 (2024-05-22 15:41:43) mtime 1716417703.220000000 (2024-05-22 15:41:43) otime 1716417703.220000000 (2024-05-22 15:41:43) item 180 key (450 INODE_REF 256) itemoff 4894 itemsize 13 index 195 namelen 3 name: 193 item 181 key (450 XATTR_ITEM 1640047104) itemoff 4857 itemsize 37 location key (0 UNKNOWN.0 0) type XATTR transid 7 data_len 1 name_len 6 name: user.a data a item 182 key (450 EXTENT_DATA 0) itemoff 4804 itemsize 53 generation 9 type 1 (regular) extent data disk byte 303144960 nr 12288 extent data offset 0 nr 8192 ram 12288 extent compression 0 (none) item 183 key (450 EXTENT_DATA 8192) itemoff 4751 itemsize 53 generation 9 type 2 (prealloc) prealloc data disk byte 303144960 nr 12288 prealloc data offset 8192 nr 4096 Item 5 in the log tree corresponds to item 183 in the filesystem tree, but nothing matches item 4. Furthermore, item 183 is the last item in the leaf. btrfs_log_prealloc_extents() is responsible for logging prealloc extents beyond i_size. It first truncates any previously logged prealloc extents that start beyond i_size. Then, it walks the filesystem tree and copies the prealloc extent items to the log tree. If it hits the end of a leaf, then it calls btrfs_next_leaf(), which unlocks the tree and does another search. However, while the filesystem tree is unlocked, an ordered extent completion may modify the tree. In particular, it may insert an extent item that overlaps with an extent item that was already copied to the log tree. This may manifest in several ways depending on the exact scenario, including an EEXIST error that is silently translated to a full sync, overlapping items in the log tree, or this crash. This particular crash is triggered by the following sequence of events: - Initially, the file has i_size=4k, a regular extent from 0-4k, and a prealloc extent beyond i_size from 4k-12k. The prealloc extent item is the last item in its B-tree leaf. - The file is fsync'd, which copies its inode item and both extent items to the log tree. - An xattr is set on the file, which sets the BTRFS_INODE_COPY_EVERYTHING flag. - The range 4k-8k in the file is written using direct I/O. i_size is extended to 8k, but the ordered extent is still in flight. - The file is fsync'd. Since BTRFS_INODE_COPY_EVERYTHING is set, this calls copy_inode_items_to_log(), which calls btrfs_log_prealloc_extents(). - btrfs_log_prealloc_extents() finds the 4k-12k prealloc extent in the filesystem tree. Since it starts before i_size, it skips it. Since it is the last item in its B-tree leaf, it calls btrfs_next_leaf(). - btrfs_next_leaf() unlocks the path. - The ordered extent completion runs, which converts the 4k-8k part of the prealloc extent to written and inserts the remaining prealloc part from 8k-12k. - btrfs_next_leaf() does a search and finds the new prealloc extent 8k-12k. - btrfs_log_prealloc_extents() copies the 8k-12k prealloc extent into the log tree. Note that it overlaps with the 4k-12k prealloc extent that was copied to the log tree by the first fsync. - fsync calls btrfs_log_changed_extents(), which tries to log the 4k-8k extent that was written. - This tries to drop the range 4k-8k in the log tree, which requires adjusting the start of the 4k-12k prealloc extent in the log tree to 8k. - btrfs_set_item_key_safe() sees that there is already an extent starting at 8k in the log tree and calls BUG(). Fix this by detecting when we're about to insert an overlapping file extent item in the log tree and truncating the part that would overlap. CC: [email protected] # 6.1+ Reviewed-by: Filipe Manana <[email protected]> Signed-off-by: Omar Sandoval <[email protected]> Signed-off-by: David Sterba <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit be346c1 upstream. The code in ocfs2_dio_end_io_write() estimates number of necessary transaction credits using ocfs2_calc_extend_credits(). This however does not take into account that the IO could be arbitrarily large and can contain arbitrary number of extents. Extent tree manipulations do often extend the current transaction but not in all of the cases. For example if we have only single block extents in the tree, ocfs2_mark_extent_written() will end up calling ocfs2_replace_extent_rec() all the time and we will never extend the current transaction and eventually exhaust all the transaction credits if the IO contains many single block extents. Once that happens a WARN_ON(jbd2_handle_buffer_credits(handle) <= 0) is triggered in jbd2_journal_dirty_metadata() and subsequently OCFS2 aborts in response to this error. This was actually triggered by one of our customers on a heavily fragmented OCFS2 filesystem. To fix the issue make sure the transaction always has enough credits for one extent insert before each call of ocfs2_mark_extent_written(). Heming Zhao said: ------ PANIC: "Kernel panic - not syncing: OCFS2: (device dm-1): panic forced after error" PID: xxx TASK: xxxx CPU: 5 COMMAND: "SubmitThread-CA" #0 machine_kexec at ffffffff8c069932 #1 __crash_kexec at ffffffff8c1338fa #2 panic at ffffffff8c1d69b9 #3 ocfs2_handle_error at ffffffffc0c86c0c [ocfs2] #4 __ocfs2_abort at ffffffffc0c88387 [ocfs2] #5 ocfs2_journal_dirty at ffffffffc0c51e98 [ocfs2] #6 ocfs2_split_extent at ffffffffc0c27ea3 [ocfs2] #7 ocfs2_change_extent_flag at ffffffffc0c28053 [ocfs2] #8 ocfs2_mark_extent_written at ffffffffc0c28347 [ocfs2] #9 ocfs2_dio_end_io_write at ffffffffc0c2bef9 [ocfs2] #10 ocfs2_dio_end_io at ffffffffc0c2c0f5 [ocfs2] #11 dio_complete at ffffffff8c2b9fa7 #12 do_blockdev_direct_IO at ffffffff8c2bc09f #13 ocfs2_direct_IO at ffffffffc0c2b653 [ocfs2] #14 generic_file_direct_write at ffffffff8c1dcf14 #15 __generic_file_write_iter at ffffffff8c1dd07b #16 ocfs2_file_write_iter at ffffffffc0c49f1f [ocfs2] #17 aio_write at ffffffff8c2cc72e #18 kmem_cache_alloc at ffffffff8c248dde #19 do_io_submit at ffffffff8c2ccada #20 do_syscall_64 at ffffffff8c004984 #21 entry_SYSCALL_64_after_hwframe at ffffffff8c8000ba Link: https://lkml.kernel.org/r/[email protected] Link: https://lkml.kernel.org/r/[email protected] Fixes: c15471f ("ocfs2: fix sparse file & data ordering issue in direct io") Signed-off-by: Jan Kara <[email protected]> Reviewed-by: Joseph Qi <[email protected]> Reviewed-by: Heming Zhao <[email protected]> Cc: Mark Fasheh <[email protected]> Cc: Joel Becker <[email protected]> Cc: Junxiao Bi <[email protected]> Cc: Changwei Ge <[email protected]> Cc: Gang He <[email protected]> Cc: Jun Piao <[email protected]> Cc: <[email protected]> Signed-off-by: Andrew Morton <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit 9eee533 upstream. KFENCE reports the following UAF: BUG: KFENCE: use-after-free read in __pci_enable_msi_range+0x2c0/0x488 Use-after-free read at 0x0000000024629571 (in kfence-#12): __pci_enable_msi_range+0x2c0/0x488 pci_alloc_irq_vectors_affinity+0xec/0x14c pci_alloc_irq_vectors+0x18/0x28 kfence-#12: 0x0000000008614900-0x00000000e06c228d, size=104, cache=kmalloc-128 allocated by task 81 on cpu 7 at 10.808142s: __kmem_cache_alloc_node+0x1f0/0x2bc kmalloc_trace+0x44/0x138 msi_alloc_desc+0x3c/0x9c msi_domain_insert_msi_desc+0x30/0x78 msi_setup_msi_desc+0x13c/0x184 __pci_enable_msi_range+0x258/0x488 pci_alloc_irq_vectors_affinity+0xec/0x14c pci_alloc_irq_vectors+0x18/0x28 freed by task 81 on cpu 7 at 10.811436s: msi_domain_free_descs+0xd4/0x10c msi_domain_free_locked.part.0+0xc0/0x1d8 msi_domain_alloc_irqs_all_locked+0xb4/0xbc pci_msi_setup_msi_irqs+0x30/0x4c __pci_enable_msi_range+0x2a8/0x488 pci_alloc_irq_vectors_affinity+0xec/0x14c pci_alloc_irq_vectors+0x18/0x28 Descriptor allocation done in: __pci_enable_msi_range msi_capability_init msi_setup_msi_desc msi_insert_msi_desc msi_domain_insert_msi_desc msi_alloc_desc ... Freed in case of failure in __msi_domain_alloc_locked() __pci_enable_msi_range msi_capability_init pci_msi_setup_msi_irqs msi_domain_alloc_irqs_all_locked msi_domain_alloc_locked __msi_domain_alloc_locked => fails msi_domain_free_locked ... That failure propagates back to pci_msi_setup_msi_irqs() in msi_capability_init() which accesses the descriptor for unmasking in the error exit path. Cure it by copying the descriptor and using the copy for the error exit path unmask operation. [ tglx: Massaged change log ] Fixes: bf6e054 ("genirq/msi: Provide msi_device_populate/destroy_sysfs()") Suggested-by: Thomas Gleixner <[email protected]> Signed-off-by: Mostafa Saleh <[email protected]> Signed-off-by: Thomas Gleixner <[email protected]> Cc: Bjorn Heelgas <[email protected]> Cc: [email protected] Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit be346c1 upstream. The code in ocfs2_dio_end_io_write() estimates number of necessary transaction credits using ocfs2_calc_extend_credits(). This however does not take into account that the IO could be arbitrarily large and can contain arbitrary number of extents. Extent tree manipulations do often extend the current transaction but not in all of the cases. For example if we have only single block extents in the tree, ocfs2_mark_extent_written() will end up calling ocfs2_replace_extent_rec() all the time and we will never extend the current transaction and eventually exhaust all the transaction credits if the IO contains many single block extents. Once that happens a WARN_ON(jbd2_handle_buffer_credits(handle) <= 0) is triggered in jbd2_journal_dirty_metadata() and subsequently OCFS2 aborts in response to this error. This was actually triggered by one of our customers on a heavily fragmented OCFS2 filesystem. To fix the issue make sure the transaction always has enough credits for one extent insert before each call of ocfs2_mark_extent_written(). Heming Zhao said: ------ PANIC: "Kernel panic - not syncing: OCFS2: (device dm-1): panic forced after error" PID: xxx TASK: xxxx CPU: 5 COMMAND: "SubmitThread-CA" #0 machine_kexec at ffffffff8c069932 #1 __crash_kexec at ffffffff8c1338fa #2 panic at ffffffff8c1d69b9 #3 ocfs2_handle_error at ffffffffc0c86c0c [ocfs2] #4 __ocfs2_abort at ffffffffc0c88387 [ocfs2] #5 ocfs2_journal_dirty at ffffffffc0c51e98 [ocfs2] #6 ocfs2_split_extent at ffffffffc0c27ea3 [ocfs2] #7 ocfs2_change_extent_flag at ffffffffc0c28053 [ocfs2] #8 ocfs2_mark_extent_written at ffffffffc0c28347 [ocfs2] #9 ocfs2_dio_end_io_write at ffffffffc0c2bef9 [ocfs2] #10 ocfs2_dio_end_io at ffffffffc0c2c0f5 [ocfs2] #11 dio_complete at ffffffff8c2b9fa7 #12 do_blockdev_direct_IO at ffffffff8c2bc09f #13 ocfs2_direct_IO at ffffffffc0c2b653 [ocfs2] #14 generic_file_direct_write at ffffffff8c1dcf14 #15 __generic_file_write_iter at ffffffff8c1dd07b #16 ocfs2_file_write_iter at ffffffffc0c49f1f [ocfs2] #17 aio_write at ffffffff8c2cc72e #18 kmem_cache_alloc at ffffffff8c248dde #19 do_io_submit at ffffffff8c2ccada #20 do_syscall_64 at ffffffff8c004984 #21 entry_SYSCALL_64_after_hwframe at ffffffff8c8000ba Link: https://lkml.kernel.org/r/[email protected] Link: https://lkml.kernel.org/r/[email protected] Fixes: c15471f ("ocfs2: fix sparse file & data ordering issue in direct io") Signed-off-by: Jan Kara <[email protected]> Reviewed-by: Joseph Qi <[email protected]> Reviewed-by: Heming Zhao <[email protected]> Cc: Mark Fasheh <[email protected]> Cc: Joel Becker <[email protected]> Cc: Junxiao Bi <[email protected]> Cc: Changwei Ge <[email protected]> Cc: Gang He <[email protected]> Cc: Jun Piao <[email protected]> Cc: <[email protected]> Signed-off-by: Andrew Morton <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit 099d906 upstream. Patch series "mm/filemap: Limit page cache size to that supported by xarray", v2. Currently, xarray can't support arbitrary page cache size. More details can be found from the WARN_ON() statement in xas_split_alloc(). In our test whose code is attached below, we hit the WARN_ON() on ARM64 system where the base page size is 64KB and huge page size is 512MB. The issue was reported long time ago and some discussions on it can be found here [1]. [1] https://www.spinics.net/lists/linux-xfs/msg75404.html In order to fix the issue, we need to adjust MAX_PAGECACHE_ORDER to one supported by xarray and avoid PMD-sized page cache if needed. The code changes are suggested by David Hildenbrand. PATCH[1] adjusts MAX_PAGECACHE_ORDER to that supported by xarray PATCH[2-3] avoids PMD-sized page cache in the synchronous readahead path PATCH[4] avoids PMD-sized page cache for shmem files if needed Test program ============ # cat test.c #define _GNU_SOURCE #include <stdio.h> #include <stdlib.h> #include <unistd.h> #include <string.h> #include <fcntl.h> #include <errno.h> #include <sys/syscall.h> #include <sys/mman.h> #define TEST_XFS_FILENAME "/tmp/data" #define TEST_SHMEM_FILENAME "/dev/shm/data" #define TEST_MEM_SIZE 0x20000000 int main(int argc, char **argv) { const char *filename; int fd = 0; void *buf = (void *)-1, *p; int pgsize = getpagesize(); int ret; if (pgsize != 0x10000) { fprintf(stderr, "64KB base page size is required\n"); return -EPERM; } system("echo force > /sys/kernel/mm/transparent_hugepage/shmem_enabled"); system("rm -fr /tmp/data"); system("rm -fr /dev/shm/data"); system("echo 1 > /proc/sys/vm/drop_caches"); /* Open xfs or shmem file */ filename = TEST_XFS_FILENAME; if (argc > 1 && !strcmp(argv[1], "shmem")) filename = TEST_SHMEM_FILENAME; fd = open(filename, O_CREAT | O_RDWR | O_TRUNC); if (fd < 0) { fprintf(stderr, "Unable to open <%s>\n", filename); return -EIO; } /* Extend file size */ ret = ftruncate(fd, TEST_MEM_SIZE); if (ret) { fprintf(stderr, "Error %d to ftruncate()\n", ret); goto cleanup; } /* Create VMA */ buf = mmap(NULL, TEST_MEM_SIZE, PROT_READ | PROT_WRITE, MAP_SHARED, fd, 0); if (buf == (void *)-1) { fprintf(stderr, "Unable to mmap <%s>\n", filename); goto cleanup; } fprintf(stdout, "mapped buffer at 0x%p\n", buf); ret = madvise(buf, TEST_MEM_SIZE, MADV_HUGEPAGE); if (ret) { fprintf(stderr, "Unable to madvise(MADV_HUGEPAGE)\n"); goto cleanup; } /* Populate VMA */ ret = madvise(buf, TEST_MEM_SIZE, MADV_POPULATE_WRITE); if (ret) { fprintf(stderr, "Error %d to madvise(MADV_POPULATE_WRITE)\n", ret); goto cleanup; } /* Punch the file to enforce xarray split */ ret = fallocate(fd, FALLOC_FL_KEEP_SIZE | FALLOC_FL_PUNCH_HOLE, TEST_MEM_SIZE - pgsize, pgsize); if (ret) fprintf(stderr, "Error %d to fallocate()\n", ret); cleanup: if (buf != (void *)-1) munmap(buf, TEST_MEM_SIZE); if (fd > 0) close(fd); return 0; } # gcc test.c -o test # cat /proc/1/smaps | grep KernelPageSize | head -n 1 KernelPageSize: 64 kB # ./test shmem : ------------[ cut here ]------------ WARNING: CPU: 17 PID: 5253 at lib/xarray.c:1025 xas_split_alloc+0xf8/0x128 Modules linked in: nft_fib_inet nft_fib_ipv4 nft_fib_ipv6 nft_fib \ nft_reject_inet nf_reject_ipv4 nf_reject_ipv6 nft_reject nft_ct \ nft_chain_nat nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 \ ip_set nf_tables rfkill nfnetlink vfat fat virtio_balloon \ drm fuse xfs libcrc32c crct10dif_ce ghash_ce sha2_ce sha256_arm64 \ virtio_net sha1_ce net_failover failover virtio_console virtio_blk \ dimlib virtio_mmio CPU: 17 PID: 5253 Comm: test Kdump: loaded Tainted: G W 6.10.0-rc5-gavin+ #12 Hardware name: QEMU KVM Virtual Machine, BIOS edk2-20240524-1.el9 05/24/2024 pstate: 83400005 (Nzcv daif +PAN -UAO +TCO +DIT -SSBS BTYPE=--) pc : xas_split_alloc+0xf8/0x128 lr : split_huge_page_to_list_to_order+0x1c4/0x720 sp : ffff80008a92f5b0 x29: ffff80008a92f5b0 x28: ffff80008a92f610 x27: ffff80008a92f728 x26: 0000000000000cc0 x25: 000000000000000d x24: ffff0000cf00c858 x23: ffff80008a92f610 x22: ffffffdfc0600000 x21: 0000000000000000 x20: 0000000000000000 x19: ffffffdfc0600000 x18: 0000000000000000 x17: 0000000000000000 x16: 0000018000000000 x15: 3374004000000000 x14: 0000e00000000000 x13: 0000000000002000 x12: 0000000000000020 x11: 3374000000000000 x10: 3374e1c0ffff6000 x9 : ffffb463a84c681c x8 : 0000000000000003 x7 : 0000000000000000 x6 : ffff00011c976ce0 x5 : ffffb463aa47e378 x4 : 0000000000000000 x3 : 0000000000000cc0 x2 : 000000000000000d x1 : 000000000000000c x0 : 0000000000000000 Call trace: xas_split_alloc+0xf8/0x128 split_huge_page_to_list_to_order+0x1c4/0x720 truncate_inode_partial_folio+0xdc/0x160 shmem_undo_range+0x2bc/0x6a8 shmem_fallocate+0x134/0x430 vfs_fallocate+0x124/0x2e8 ksys_fallocate+0x4c/0xa0 __arm64_sys_fallocate+0x24/0x38 invoke_syscall.constprop.0+0x7c/0xd8 do_el0_svc+0xb4/0xd0 el0_svc+0x44/0x1d8 el0t_64_sync_handler+0x134/0x150 el0t_64_sync+0x17c/0x180 This patch (of 4): The largest page cache order can be HPAGE_PMD_ORDER (13) on ARM64 with 64KB base page size. The xarray entry with this order can't be split as the following error messages indicate. ------------[ cut here ]------------ WARNING: CPU: 35 PID: 7484 at lib/xarray.c:1025 xas_split_alloc+0xf8/0x128 Modules linked in: nft_fib_inet nft_fib_ipv4 nft_fib_ipv6 nft_fib \ nft_reject_inet nf_reject_ipv4 nf_reject_ipv6 nft_reject nft_ct \ nft_chain_nat nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 \ ip_set rfkill nf_tables nfnetlink vfat fat virtio_balloon drm \ fuse xfs libcrc32c crct10dif_ce ghash_ce sha2_ce sha256_arm64 \ sha1_ce virtio_net net_failover virtio_console virtio_blk failover \ dimlib virtio_mmio CPU: 35 PID: 7484 Comm: test Kdump: loaded Tainted: G W 6.10.0-rc5-gavin+ #9 Hardware name: QEMU KVM Virtual Machine, BIOS edk2-20240524-1.el9 05/24/2024 pstate: 83400005 (Nzcv daif +PAN -UAO +TCO +DIT -SSBS BTYPE=--) pc : xas_split_alloc+0xf8/0x128 lr : split_huge_page_to_list_to_order+0x1c4/0x720 sp : ffff800087a4f6c0 x29: ffff800087a4f6c0 x28: ffff800087a4f720 x27: 000000001fffffff x26: 0000000000000c40 x25: 000000000000000d x24: ffff00010625b858 x23: ffff800087a4f720 x22: ffffffdfc0780000 x21: 0000000000000000 x20: 0000000000000000 x19: ffffffdfc0780000 x18: 000000001ff40000 x17: 00000000ffffffff x16: 0000018000000000 x15: 51ec004000000000 x14: 0000e00000000000 x13: 0000000000002000 x12: 0000000000000020 x11: 51ec000000000000 x10: 51ece1c0ffff8000 x9 : ffffbeb961a44d28 x8 : 0000000000000003 x7 : ffffffdfc0456420 x6 : ffff0000e1aa6eb8 x5 : 20bf08b4fe778fca x4 : ffffffdfc0456420 x3 : 0000000000000c40 x2 : 000000000000000d x1 : 000000000000000c x0 : 0000000000000000 Call trace: xas_split_alloc+0xf8/0x128 split_huge_page_to_list_to_order+0x1c4/0x720 truncate_inode_partial_folio+0xdc/0x160 truncate_inode_pages_range+0x1b4/0x4a8 truncate_pagecache_range+0x84/0xa0 xfs_flush_unmap_range+0x70/0x90 [xfs] xfs_file_fallocate+0xfc/0x4d8 [xfs] vfs_fallocate+0x124/0x2e8 ksys_fallocate+0x4c/0xa0 __arm64_sys_fallocate+0x24/0x38 invoke_syscall.constprop.0+0x7c/0xd8 do_el0_svc+0xb4/0xd0 el0_svc+0x44/0x1d8 el0t_64_sync_handler+0x134/0x150 el0t_64_sync+0x17c/0x180 Fix it by decreasing MAX_PAGECACHE_ORDER to the largest supported order by xarray. For this specific case, MAX_PAGECACHE_ORDER is dropped from 13 to 11 when CONFIG_BASE_SMALL is disabled. Link: https://lkml.kernel.org/r/[email protected] Link: https://lkml.kernel.org/r/[email protected] Fixes: 793917d ("mm/readahead: Add large folio readahead") Signed-off-by: Gavin Shan <[email protected]> Suggested-by: David Hildenbrand <[email protected]> Acked-by: David Hildenbrand <[email protected]> Cc: Darrick J. Wong <[email protected]> Cc: Don Dutile <[email protected]> Cc: Hugh Dickins <[email protected]> Cc: Linus Torvalds <[email protected]> Cc: Matthew Wilcox (Oracle) <[email protected]> Cc: Ryan Roberts <[email protected]> Cc: William Kucharski <[email protected]> Cc: Zhenyu Zhang <[email protected]> Cc: <[email protected]> [5.18+] Signed-off-by: Andrew Morton <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

[ Upstream commit f8cde98 ] We shouldn't set real_dev to NULL because packets can be in transit and xfrm might call xdo_dev_offload_ok() in parallel. All callbacks assume real_dev is set. Example trace: kernel: BUG: unable to handle page fault for address: 0000000000001030 kernel: bond0: (slave eni0np1): making interface the new active one kernel: #PF: supervisor write access in kernel mode kernel: #PF: error_code(0x0002) - not-present page kernel: PGD 0 P4D 0 kernel: Oops: 0002 [#1] PREEMPT SMP kernel: CPU: 4 PID: 2237 Comm: ping Not tainted 6.7.7+ #12 kernel: Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-2.fc40 04/01/2014 kernel: RIP: 0010:nsim_ipsec_offload_ok+0xc/0x20 [netdevsim] kernel: bond0: (slave eni0np1): bond_ipsec_add_sa_all: failed to add SA kernel: Code: e0 0f 0b 48 83 7f 38 00 74 de 0f 0b 48 8b 47 08 48 8b 37 48 8b 78 40 e9 b2 e5 9a d7 66 90 0f 1f 44 00 00 48 8b 86 80 02 00 00 <83> 80 30 10 00 00 01 b8 01 00 00 00 c3 0f 1f 80 00 00 00 00 0f 1f kernel: bond0: (slave eni0np1): making interface the new active one kernel: RSP: 0018:ffffabde81553b98 EFLAGS: 00010246 kernel: bond0: (slave eni0np1): bond_ipsec_add_sa_all: failed to add SA kernel: kernel: RAX: 0000000000000000 RBX: ffff9eb404e74900 RCX: ffff9eb403d97c60 kernel: RDX: ffffffffc090de10 RSI: ffff9eb404e74900 RDI: ffff9eb3c5de9e00 kernel: RBP: ffff9eb3c0a42000 R08: 0000000000000010 R09: 0000000000000014 kernel: R10: 7974203030303030 R11: 3030303030303030 R12: 0000000000000000 kernel: R13: ffff9eb3c5de9e00 R14: ffffabde81553cc8 R15: ffff9eb404c53000 kernel: FS: 00007f2a77a3ad00(0000) GS:ffff9eb43bd00000(0000) knlGS:0000000000000000 kernel: CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 kernel: CR2: 0000000000001030 CR3: 00000001122ab000 CR4: 0000000000350ef0 kernel: bond0: (slave eni0np1): making interface the new active one kernel: Call Trace: kernel: <TASK> kernel: ? __die+0x1f/0x60 kernel: bond0: (slave eni0np1): bond_ipsec_add_sa_all: failed to add SA kernel: ? page_fault_oops+0x142/0x4c0 kernel: ? do_user_addr_fault+0x65/0x670 kernel: ? kvm_read_and_reset_apf_flags+0x3b/0x50 kernel: bond0: (slave eni0np1): making interface the new active one kernel: ? exc_page_fault+0x7b/0x180 kernel: ? asm_exc_page_fault+0x22/0x30 kernel: ? nsim_bpf_uninit+0x50/0x50 [netdevsim] kernel: bond0: (slave eni0np1): bond_ipsec_add_sa_all: failed to add SA kernel: ? nsim_ipsec_offload_ok+0xc/0x20 [netdevsim] kernel: bond0: (slave eni0np1): making interface the new active one kernel: bond_ipsec_offload_ok+0x7b/0x90 [bonding] kernel: xfrm_output+0x61/0x3b0 kernel: bond0: (slave eni0np1): bond_ipsec_add_sa_all: failed to add SA kernel: ip_push_pending_frames+0x56/0x80 Fixes: 18cb261 ("bonding: support hardware encryption offload to slaves") Signed-off-by: Nikolay Aleksandrov <[email protected]> Reviewed-by: Hangbin Liu <[email protected]> Signed-off-by: Paolo Abeni <[email protected]> Signed-off-by: Sasha Levin <[email protected]>

[ Upstream commit a699781 ] A sysfs reader can race with a device reset or removal, attempting to read device state when the device is not actually present. eg: [exception RIP: qed_get_current_link+17] #8 [ffffb9e4f2907c48] qede_get_link_ksettings at ffffffffc07a994a [qede] #9 [ffffb9e4f2907cd8] __rh_call_get_link_ksettings at ffffffff992b01a3 #10 [ffffb9e4f2907d38] __ethtool_get_link_ksettings at ffffffff992b04e4 #11 [ffffb9e4f2907d90] duplex_show at ffffffff99260300 #12 [ffffb9e4f2907e38] dev_attr_show at ffffffff9905a01c #13 [ffffb9e4f2907e50] sysfs_kf_seq_show at ffffffff98e0145b #14 [ffffb9e4f2907e68] seq_read at ffffffff98d902e3 #15 [ffffb9e4f2907ec8] vfs_read at ffffffff98d657d1 #16 [ffffb9e4f2907f00] ksys_read at ffffffff98d65c3f #17 [ffffb9e4f2907f38] do_syscall_64 at ffffffff98a052fb crash> struct net_device.state ffff9a9d21336000 state = 5, state 5 is __LINK_STATE_START (0b1) and __LINK_STATE_NOCARRIER (0b100). The device is not present, note lack of __LINK_STATE_PRESENT (0b10). This is the same sort of panic as observed in commit 4224cfd ("net-sysfs: add check for netdevice being present to speed_show"). There are many other callers of __ethtool_get_link_ksettings() which don't have a device presence check. Move this check into ethtool to protect all callers. Fixes: d519e17 ("net: export device speed and duplex via sysfs") Fixes: 4224cfd ("net-sysfs: add check for netdevice being present to speed_show") Signed-off-by: Jamie Bainbridge <[email protected]> Link: https://patch.msgid.link/8bae218864beaa44ed01628140475b9bf641c5b0.1724393671.git.jamie.bainbridge@gmail.com Signed-off-by: Jakub Kicinski <[email protected]> Signed-off-by: Sasha Levin <[email protected]>

commit 9eee533 upstream. KFENCE reports the following UAF: BUG: KFENCE: use-after-free read in __pci_enable_msi_range+0x2c0/0x488 Use-after-free read at 0x0000000024629571 (in kfence-#12): __pci_enable_msi_range+0x2c0/0x488 pci_alloc_irq_vectors_affinity+0xec/0x14c pci_alloc_irq_vectors+0x18/0x28 kfence-#12: 0x0000000008614900-0x00000000e06c228d, size=104, cache=kmalloc-128 allocated by task 81 on cpu 7 at 10.808142s: __kmem_cache_alloc_node+0x1f0/0x2bc kmalloc_trace+0x44/0x138 msi_alloc_desc+0x3c/0x9c msi_domain_insert_msi_desc+0x30/0x78 msi_setup_msi_desc+0x13c/0x184 __pci_enable_msi_range+0x258/0x488 pci_alloc_irq_vectors_affinity+0xec/0x14c pci_alloc_irq_vectors+0x18/0x28 freed by task 81 on cpu 7 at 10.811436s: msi_domain_free_descs+0xd4/0x10c msi_domain_free_locked.part.0+0xc0/0x1d8 msi_domain_alloc_irqs_all_locked+0xb4/0xbc pci_msi_setup_msi_irqs+0x30/0x4c __pci_enable_msi_range+0x2a8/0x488 pci_alloc_irq_vectors_affinity+0xec/0x14c pci_alloc_irq_vectors+0x18/0x28 Descriptor allocation done in: __pci_enable_msi_range msi_capability_init msi_setup_msi_desc msi_insert_msi_desc msi_domain_insert_msi_desc msi_alloc_desc ... Freed in case of failure in __msi_domain_alloc_locked() __pci_enable_msi_range msi_capability_init pci_msi_setup_msi_irqs msi_domain_alloc_irqs_all_locked msi_domain_alloc_locked __msi_domain_alloc_locked => fails msi_domain_free_locked ... That failure propagates back to pci_msi_setup_msi_irqs() in msi_capability_init() which accesses the descriptor for unmasking in the error exit path. Cure it by copying the descriptor and using the copy for the error exit path unmask operation. [ tglx: Massaged change log ] Fixes: bf6e054 ("genirq/msi: Provide msi_device_populate/destroy_sysfs()") Suggested-by: Thomas Gleixner <[email protected]> Signed-off-by: Mostafa Saleh <[email protected]> Signed-off-by: Thomas Gleixner <[email protected]> Cc: Bjorn Heelgas <[email protected]> Cc: [email protected] Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Hugo SIMELIERE <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit ac01c8c upstream. AddressSanitizer found a use-after-free bug in the symbol code which manifested as 'perf top' segfaulting. ==1238389==ERROR: AddressSanitizer: heap-use-after-free on address 0x60b00c48844b at pc 0x5650d8035961 bp 0x7f751aaecc90 sp 0x7f751aaecc80 READ of size 1 at 0x60b00c48844b thread T193 #0 0x5650d8035960 in _sort__sym_cmp util/sort.c:310 #1 0x5650d8043744 in hist_entry__cmp util/hist.c:1286 #2 0x5650d8043951 in hists__findnew_entry util/hist.c:614 #3 0x5650d804568f in __hists__add_entry util/hist.c:754 #4 0x5650d8045bf9 in hists__add_entry util/hist.c:772 #5 0x5650d8045df1 in iter_add_single_normal_entry util/hist.c:997 #6 0x5650d8043326 in hist_entry_iter__add util/hist.c:1242 #7 0x5650d7ceeefe in perf_event__process_sample /home/matt/src/linux/tools/perf/builtin-top.c:845 #8 0x5650d7ceeefe in deliver_event /home/matt/src/linux/tools/perf/builtin-top.c:1208 #9 0x5650d7fdb51b in do_flush util/ordered-events.c:245 #10 0x5650d7fdb51b in __ordered_events__flush util/ordered-events.c:324 #11 0x5650d7ced743 in process_thread /home/matt/src/linux/tools/perf/builtin-top.c:1120 #12 0x7f757ef1f133 in start_thread nptl/pthread_create.c:442 #13 0x7f757ef9f7db in clone3 ../sysdeps/unix/sysv/linux/x86_64/clone3.S:81 When updating hist maps it's also necessary to update the hist symbol reference because the old one gets freed in map__put(). While this bug was probably introduced with 5c24b67 ("perf tools: Replace map->referenced & maps->removed_maps with map->refcnt"), the symbol objects were leaked until c087e94 ("perf machine: Fix refcount usage when processing PERF_RECORD_KSYMBOL") was merged so the bug was masked. Fixes: c087e94 ("perf machine: Fix refcount usage when processing PERF_RECORD_KSYMBOL") Reported-by: Yunzhao Li <[email protected]> Signed-off-by: Matt Fleming (Cloudflare) <[email protected]> Cc: Ian Rogers <[email protected]> Cc: [email protected] Cc: Namhyung Kim <[email protected]> Cc: Riccardo Mancini <[email protected]> Cc: [email protected] # v5.13+ Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Arnaldo Carvalho de Melo <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit 9af2efe upstream. The fields in the hist_entry are filled on-demand which means they only have meaningful values when relevant sort keys are used. So if neither of 'dso' nor 'sym' sort keys are used, the map/symbols in the hist entry can be garbage. So it shouldn't access it unconditionally. I got a segfault, when I wanted to see cgroup profiles. $ sudo perf record -a --all-cgroups --synth=cgroup true $ sudo perf report -s cgroup Program received signal SIGSEGV, Segmentation fault. 0x00005555557a8d90 in map__dso (map=0x0) at util/map.h:48 48 return RC_CHK_ACCESS(map)->dso; (gdb) bt #0 0x00005555557a8d90 in map__dso (map=0x0) at util/map.h:48 #1 0x00005555557aa39b in map__load (map=0x0) at util/map.c:344 #2 0x00005555557aa592 in map__find_symbol (map=0x0, addr=140736115941088) at util/map.c:385 #3 0x00005555557ef000 in hists__findnew_entry (hists=0x555556039d60, entry=0x7fffffffa4c0, al=0x7fffffffa8c0, sample_self=true) at util/hist.c:644 #4 0x00005555557ef61c in __hists__add_entry (hists=0x555556039d60, al=0x7fffffffa8c0, sym_parent=0x0, bi=0x0, mi=0x0, ki=0x0, block_info=0x0, sample=0x7fffffffaa90, sample_self=true, ops=0x0) at util/hist.c:761 #5 0x00005555557ef71f in hists__add_entry (hists=0x555556039d60, al=0x7fffffffa8c0, sym_parent=0x0, bi=0x0, mi=0x0, ki=0x0, sample=0x7fffffffaa90, sample_self=true) at util/hist.c:779 #6 0x00005555557f00fb in iter_add_single_normal_entry (iter=0x7fffffffa900, al=0x7fffffffa8c0) at util/hist.c:1015 #7 0x00005555557f09a7 in hist_entry_iter__add (iter=0x7fffffffa900, al=0x7fffffffa8c0, max_stack_depth=127, arg=0x7fffffffbce0) at util/hist.c:1260 #8 0x00005555555ba7ce in process_sample_event (tool=0x7fffffffbce0, event=0x7ffff7c14128, sample=0x7fffffffaa90, evsel=0x555556039ad0, machine=0x5555560388e8) at builtin-report.c:334 #9 0x00005555557b30c8 in evlist__deliver_sample (evlist=0x555556039010, tool=0x7fffffffbce0, event=0x7ffff7c14128, sample=0x7fffffffaa90, evsel=0x555556039ad0, machine=0x5555560388e8) at util/session.c:1232 #10 0x00005555557b32bc in machines__deliver_event (machines=0x5555560388e8, evlist=0x555556039010, event=0x7ffff7c14128, sample=0x7fffffffaa90, tool=0x7fffffffbce0, file_offset=110888, file_path=0x555556038ff0 "perf.data") at util/session.c:1271 #11 0x00005555557b3848 in perf_session__deliver_event (session=0x5555560386d0, event=0x7ffff7c14128, tool=0x7fffffffbce0, file_offset=110888, file_path=0x555556038ff0 "perf.data") at util/session.c:1354 #12 0x00005555557affaf in ordered_events__deliver_event (oe=0x555556038e60, event=0x555556135aa0) at util/session.c:132 #13 0x00005555557bb605 in do_flush (oe=0x555556038e60, show_progress=false) at util/ordered-events.c:245 #14 0x00005555557bb95c in __ordered_events__flush (oe=0x555556038e60, how=OE_FLUSH__ROUND, timestamp=0) at util/ordered-events.c:324 #15 0x00005555557bba46 in ordered_events__flush (oe=0x555556038e60, how=OE_FLUSH__ROUND) at util/ordered-events.c:342 #16 0x00005555557b1b3b in perf_event__process_finished_round (tool=0x7fffffffbce0, event=0x7ffff7c15bb8, oe=0x555556038e60) at util/session.c:780 #17 0x00005555557b3b27 in perf_session__process_user_event (session=0x5555560386d0, event=0x7ffff7c15bb8, file_offset=117688, file_path=0x555556038ff0 "perf.data") at util/session.c:1406 As you can see the entry->ms.map was NULL even if he->ms.map has a value. This is because 'sym' sort key is not given, so it cannot assume whether he->ms.sym and entry->ms.sym is the same. I only checked the 'sym' sort key here as it implies 'dso' behavior (so maps are the same). Fixes: ac01c8c ("perf hist: Update hist symbol when updating maps") Signed-off-by: Namhyung Kim <[email protected]> Cc: Adrian Hunter <[email protected]> Cc: Ian Rogers <[email protected]> Cc: Ingo Molnar <[email protected]> Cc: Jiri Olsa <[email protected]> Cc: Kan Liang <[email protected]> Cc: Matt Fleming <[email protected]> Cc: Peter Zijlstra <[email protected]> Cc: Stephane Eranian <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Arnaldo Carvalho de Melo <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit ac01c8c upstream. AddressSanitizer found a use-after-free bug in the symbol code which manifested as 'perf top' segfaulting. ==1238389==ERROR: AddressSanitizer: heap-use-after-free on address 0x60b00c48844b at pc 0x5650d8035961 bp 0x7f751aaecc90 sp 0x7f751aaecc80 READ of size 1 at 0x60b00c48844b thread T193 #0 0x5650d8035960 in _sort__sym_cmp util/sort.c:310 #1 0x5650d8043744 in hist_entry__cmp util/hist.c:1286 #2 0x5650d8043951 in hists__findnew_entry util/hist.c:614 #3 0x5650d804568f in __hists__add_entry util/hist.c:754 #4 0x5650d8045bf9 in hists__add_entry util/hist.c:772 #5 0x5650d8045df1 in iter_add_single_normal_entry util/hist.c:997 #6 0x5650d8043326 in hist_entry_iter__add util/hist.c:1242 #7 0x5650d7ceeefe in perf_event__process_sample /home/matt/src/linux/tools/perf/builtin-top.c:845 #8 0x5650d7ceeefe in deliver_event /home/matt/src/linux/tools/perf/builtin-top.c:1208 #9 0x5650d7fdb51b in do_flush util/ordered-events.c:245 #10 0x5650d7fdb51b in __ordered_events__flush util/ordered-events.c:324 #11 0x5650d7ced743 in process_thread /home/matt/src/linux/tools/perf/builtin-top.c:1120 #12 0x7f757ef1f133 in start_thread nptl/pthread_create.c:442 #13 0x7f757ef9f7db in clone3 ../sysdeps/unix/sysv/linux/x86_64/clone3.S:81 When updating hist maps it's also necessary to update the hist symbol reference because the old one gets freed in map__put(). While this bug was probably introduced with 5c24b67 ("perf tools: Replace map->referenced & maps->removed_maps with map->refcnt"), the symbol objects were leaked until c087e94 ("perf machine: Fix refcount usage when processing PERF_RECORD_KSYMBOL") was merged so the bug was masked. Fixes: c087e94 ("perf machine: Fix refcount usage when processing PERF_RECORD_KSYMBOL") Reported-by: Yunzhao Li <[email protected]> Signed-off-by: Matt Fleming (Cloudflare) <[email protected]> Cc: Ian Rogers <[email protected]> Cc: [email protected] Cc: Namhyung Kim <[email protected]> Cc: Riccardo Mancini <[email protected]> Cc: [email protected] # v5.13+ Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Arnaldo Carvalho de Melo <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit 9af2efe upstream. The fields in the hist_entry are filled on-demand which means they only have meaningful values when relevant sort keys are used. So if neither of 'dso' nor 'sym' sort keys are used, the map/symbols in the hist entry can be garbage. So it shouldn't access it unconditionally. I got a segfault, when I wanted to see cgroup profiles. $ sudo perf record -a --all-cgroups --synth=cgroup true $ sudo perf report -s cgroup Program received signal SIGSEGV, Segmentation fault. 0x00005555557a8d90 in map__dso (map=0x0) at util/map.h:48 48 return RC_CHK_ACCESS(map)->dso; (gdb) bt #0 0x00005555557a8d90 in map__dso (map=0x0) at util/map.h:48 #1 0x00005555557aa39b in map__load (map=0x0) at util/map.c:344 #2 0x00005555557aa592 in map__find_symbol (map=0x0, addr=140736115941088) at util/map.c:385 #3 0x00005555557ef000 in hists__findnew_entry (hists=0x555556039d60, entry=0x7fffffffa4c0, al=0x7fffffffa8c0, sample_self=true) at util/hist.c:644 #4 0x00005555557ef61c in __hists__add_entry (hists=0x555556039d60, al=0x7fffffffa8c0, sym_parent=0x0, bi=0x0, mi=0x0, ki=0x0, block_info=0x0, sample=0x7fffffffaa90, sample_self=true, ops=0x0) at util/hist.c:761 #5 0x00005555557ef71f in hists__add_entry (hists=0x555556039d60, al=0x7fffffffa8c0, sym_parent=0x0, bi=0x0, mi=0x0, ki=0x0, sample=0x7fffffffaa90, sample_self=true) at util/hist.c:779 #6 0x00005555557f00fb in iter_add_single_normal_entry (iter=0x7fffffffa900, al=0x7fffffffa8c0) at util/hist.c:1015 #7 0x00005555557f09a7 in hist_entry_iter__add (iter=0x7fffffffa900, al=0x7fffffffa8c0, max_stack_depth=127, arg=0x7fffffffbce0) at util/hist.c:1260 #8 0x00005555555ba7ce in process_sample_event (tool=0x7fffffffbce0, event=0x7ffff7c14128, sample=0x7fffffffaa90, evsel=0x555556039ad0, machine=0x5555560388e8) at builtin-report.c:334 #9 0x00005555557b30c8 in evlist__deliver_sample (evlist=0x555556039010, tool=0x7fffffffbce0, event=0x7ffff7c14128, sample=0x7fffffffaa90, evsel=0x555556039ad0, machine=0x5555560388e8) at util/session.c:1232 #10 0x00005555557b32bc in machines__deliver_event (machines=0x5555560388e8, evlist=0x555556039010, event=0x7ffff7c14128, sample=0x7fffffffaa90, tool=0x7fffffffbce0, file_offset=110888, file_path=0x555556038ff0 "perf.data") at util/session.c:1271 #11 0x00005555557b3848 in perf_session__deliver_event (session=0x5555560386d0, event=0x7ffff7c14128, tool=0x7fffffffbce0, file_offset=110888, file_path=0x555556038ff0 "perf.data") at util/session.c:1354 #12 0x00005555557affaf in ordered_events__deliver_event (oe=0x555556038e60, event=0x555556135aa0) at util/session.c:132 #13 0x00005555557bb605 in do_flush (oe=0x555556038e60, show_progress=false) at util/ordered-events.c:245 #14 0x00005555557bb95c in __ordered_events__flush (oe=0x555556038e60, how=OE_FLUSH__ROUND, timestamp=0) at util/ordered-events.c:324 #15 0x00005555557bba46 in ordered_events__flush (oe=0x555556038e60, how=OE_FLUSH__ROUND) at util/ordered-events.c:342 #16 0x00005555557b1b3b in perf_event__process_finished_round (tool=0x7fffffffbce0, event=0x7ffff7c15bb8, oe=0x555556038e60) at util/session.c:780 #17 0x00005555557b3b27 in perf_session__process_user_event (session=0x5555560386d0, event=0x7ffff7c15bb8, file_offset=117688, file_path=0x555556038ff0 "perf.data") at util/session.c:1406 As you can see the entry->ms.map was NULL even if he->ms.map has a value. This is because 'sym' sort key is not given, so it cannot assume whether he->ms.sym and entry->ms.sym is the same. I only checked the 'sym' sort key here as it implies 'dso' behavior (so maps are the same). Fixes: ac01c8c ("perf hist: Update hist symbol when updating maps") Signed-off-by: Namhyung Kim <[email protected]> Cc: Adrian Hunter <[email protected]> Cc: Ian Rogers <[email protected]> Cc: Ingo Molnar <[email protected]> Cc: Jiri Olsa <[email protected]> Cc: Kan Liang <[email protected]> Cc: Matt Fleming <[email protected]> Cc: Peter Zijlstra <[email protected]> Cc: Stephane Eranian <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Arnaldo Carvalho de Melo <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit ac01c8c upstream. AddressSanitizer found a use-after-free bug in the symbol code which manifested as 'perf top' segfaulting. ==1238389==ERROR: AddressSanitizer: heap-use-after-free on address 0x60b00c48844b at pc 0x5650d8035961 bp 0x7f751aaecc90 sp 0x7f751aaecc80 READ of size 1 at 0x60b00c48844b thread T193 #0 0x5650d8035960 in _sort__sym_cmp util/sort.c:310 #1 0x5650d8043744 in hist_entry__cmp util/hist.c:1286 #2 0x5650d8043951 in hists__findnew_entry util/hist.c:614 #3 0x5650d804568f in __hists__add_entry util/hist.c:754 #4 0x5650d8045bf9 in hists__add_entry util/hist.c:772 #5 0x5650d8045df1 in iter_add_single_normal_entry util/hist.c:997 #6 0x5650d8043326 in hist_entry_iter__add util/hist.c:1242 #7 0x5650d7ceeefe in perf_event__process_sample /home/matt/src/linux/tools/perf/builtin-top.c:845 #8 0x5650d7ceeefe in deliver_event /home/matt/src/linux/tools/perf/builtin-top.c:1208 #9 0x5650d7fdb51b in do_flush util/ordered-events.c:245 #10 0x5650d7fdb51b in __ordered_events__flush util/ordered-events.c:324 #11 0x5650d7ced743 in process_thread /home/matt/src/linux/tools/perf/builtin-top.c:1120 #12 0x7f757ef1f133 in start_thread nptl/pthread_create.c:442 #13 0x7f757ef9f7db in clone3 ../sysdeps/unix/sysv/linux/x86_64/clone3.S:81 When updating hist maps it's also necessary to update the hist symbol reference because the old one gets freed in map__put(). While this bug was probably introduced with 5c24b67 ("perf tools: Replace map->referenced & maps->removed_maps with map->refcnt"), the symbol objects were leaked until c087e94 ("perf machine: Fix refcount usage when processing PERF_RECORD_KSYMBOL") was merged so the bug was masked. Fixes: c087e94 ("perf machine: Fix refcount usage when processing PERF_RECORD_KSYMBOL") Reported-by: Yunzhao Li <[email protected]> Signed-off-by: Matt Fleming (Cloudflare) <[email protected]> Cc: Ian Rogers <[email protected]> Cc: [email protected] Cc: Namhyung Kim <[email protected]> Cc: Riccardo Mancini <[email protected]> Cc: [email protected] # v5.13+ Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Arnaldo Carvalho de Melo <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit 9af2efe upstream. The fields in the hist_entry are filled on-demand which means they only have meaningful values when relevant sort keys are used. So if neither of 'dso' nor 'sym' sort keys are used, the map/symbols in the hist entry can be garbage. So it shouldn't access it unconditionally. I got a segfault, when I wanted to see cgroup profiles. $ sudo perf record -a --all-cgroups --synth=cgroup true $ sudo perf report -s cgroup Program received signal SIGSEGV, Segmentation fault. 0x00005555557a8d90 in map__dso (map=0x0) at util/map.h:48 48 return RC_CHK_ACCESS(map)->dso; (gdb) bt #0 0x00005555557a8d90 in map__dso (map=0x0) at util/map.h:48 #1 0x00005555557aa39b in map__load (map=0x0) at util/map.c:344 #2 0x00005555557aa592 in map__find_symbol (map=0x0, addr=140736115941088) at util/map.c:385 #3 0x00005555557ef000 in hists__findnew_entry (hists=0x555556039d60, entry=0x7fffffffa4c0, al=0x7fffffffa8c0, sample_self=true) at util/hist.c:644 #4 0x00005555557ef61c in __hists__add_entry (hists=0x555556039d60, al=0x7fffffffa8c0, sym_parent=0x0, bi=0x0, mi=0x0, ki=0x0, block_info=0x0, sample=0x7fffffffaa90, sample_self=true, ops=0x0) at util/hist.c:761 #5 0x00005555557ef71f in hists__add_entry (hists=0x555556039d60, al=0x7fffffffa8c0, sym_parent=0x0, bi=0x0, mi=0x0, ki=0x0, sample=0x7fffffffaa90, sample_self=true) at util/hist.c:779 #6 0x00005555557f00fb in iter_add_single_normal_entry (iter=0x7fffffffa900, al=0x7fffffffa8c0) at util/hist.c:1015 #7 0x00005555557f09a7 in hist_entry_iter__add (iter=0x7fffffffa900, al=0x7fffffffa8c0, max_stack_depth=127, arg=0x7fffffffbce0) at util/hist.c:1260 #8 0x00005555555ba7ce in process_sample_event (tool=0x7fffffffbce0, event=0x7ffff7c14128, sample=0x7fffffffaa90, evsel=0x555556039ad0, machine=0x5555560388e8) at builtin-report.c:334 #9 0x00005555557b30c8 in evlist__deliver_sample (evlist=0x555556039010, tool=0x7fffffffbce0, event=0x7ffff7c14128, sample=0x7fffffffaa90, evsel=0x555556039ad0, machine=0x5555560388e8) at util/session.c:1232 #10 0x00005555557b32bc in machines__deliver_event (machines=0x5555560388e8, evlist=0x555556039010, event=0x7ffff7c14128, sample=0x7fffffffaa90, tool=0x7fffffffbce0, file_offset=110888, file_path=0x555556038ff0 "perf.data") at util/session.c:1271 #11 0x00005555557b3848 in perf_session__deliver_event (session=0x5555560386d0, event=0x7ffff7c14128, tool=0x7fffffffbce0, file_offset=110888, file_path=0x555556038ff0 "perf.data") at util/session.c:1354 #12 0x00005555557affaf in ordered_events__deliver_event (oe=0x555556038e60, event=0x555556135aa0) at util/session.c:132 #13 0x00005555557bb605 in do_flush (oe=0x555556038e60, show_progress=false) at util/ordered-events.c:245 #14 0x00005555557bb95c in __ordered_events__flush (oe=0x555556038e60, how=OE_FLUSH__ROUND, timestamp=0) at util/ordered-events.c:324 #15 0x00005555557bba46 in ordered_events__flush (oe=0x555556038e60, how=OE_FLUSH__ROUND) at util/ordered-events.c:342 #16 0x00005555557b1b3b in perf_event__process_finished_round (tool=0x7fffffffbce0, event=0x7ffff7c15bb8, oe=0x555556038e60) at util/session.c:780 #17 0x00005555557b3b27 in perf_session__process_user_event (session=0x5555560386d0, event=0x7ffff7c15bb8, file_offset=117688, file_path=0x555556038ff0 "perf.data") at util/session.c:1406 As you can see the entry->ms.map was NULL even if he->ms.map has a value. This is because 'sym' sort key is not given, so it cannot assume whether he->ms.sym and entry->ms.sym is the same. I only checked the 'sym' sort key here as it implies 'dso' behavior (so maps are the same). Fixes: ac01c8c ("perf hist: Update hist symbol when updating maps") Signed-off-by: Namhyung Kim <[email protected]> Cc: Adrian Hunter <[email protected]> Cc: Ian Rogers <[email protected]> Cc: Ingo Molnar <[email protected]> Cc: Jiri Olsa <[email protected]> Cc: Kan Liang <[email protected]> Cc: Matt Fleming <[email protected]> Cc: Peter Zijlstra <[email protected]> Cc: Stephane Eranian <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Arnaldo Carvalho de Melo <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit c7acef9 upstream. Dennis reports a boot crash on recent Lenovo laptops with a USB4 dock. Since commit 0fc7088 ("thunderbolt: Reset USB4 v2 host router") and commit 59a54c5 ("thunderbolt: Reset topology created by the boot firmware"), USB4 v2 and v1 Host Routers are reset on probe of the thunderbolt driver. The reset clears the Presence Detect State and Data Link Layer Link Active bits at the USB4 Host Router's Root Port and thus causes hot removal of the dock. The crash occurs when pciehp is unbound from one of the dock's Downstream Ports: pciehp creates a pci_slot on bind and destroys it on unbind. The pci_slot contains a pointer to the pci_bus below the Downstream Port, but a reference on that pci_bus is never acquired. The pci_bus is destroyed before the pci_slot, so a use-after-free ensues when pci_slot_release() accesses slot->bus. In principle this should not happen because pci_stop_bus_device() unbinds pciehp (and therefore destroys the pci_slot) before the pci_bus is destroyed by pci_remove_bus_device(). However the stacktrace provided by Dennis shows that pciehp is unbound from pci_remove_bus_device() instead of pci_stop_bus_device(). To understand the significance of this, one needs to know that the PCI core uses a two step process to remove a portion of the hierarchy: It first unbinds all drivers in the sub-hierarchy in pci_stop_bus_device() and then actually removes the devices in pci_remove_bus_device(). There is no precaution to prevent driver binding in-between pci_stop_bus_device() and pci_remove_bus_device(). In Dennis' case, it seems removal of the hierarchy by pciehp races with driver binding by pci_bus_add_devices(). pciehp is bound to the Downstream Port after pci_stop_bus_device() has run, so it is unbound by pci_remove_bus_device() instead of pci_stop_bus_device(). Because the pci_bus has already been destroyed at that point, accesses to it result in a use-after-free. One might conclude that driver binding needs to be prevented after pci_stop_bus_device() has run. However it seems risky that pci_slot points to pci_bus without holding a reference. Solely relying on correct ordering of driver unbind versus pci_bus destruction is certainly not defensive programming. If pci_slot has a need to access data in pci_bus, it ought to acquire a reference. Amend pci_create_slot() accordingly. Dennis reports that the crash is not reproducible with this change. Abridged stacktrace: pcieport 0000:00:07.0: PME: Signaling with IRQ 156 pcieport 0000:00:07.0: pciehp: Slot #12 AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surprise+ Interlock- NoCompl+ IbPresDis- LLActRep+ pci_bus 0000:20: dev 00, created physical slot 12 pcieport 0000:00:07.0: pciehp: Slot(12): Card not present ... pcieport 0000:21:02.0: pciehp: pcie_disable_notification: SLOTCTRL d8 write cmd 0 Oops: general protection fault, probably for non-canonical address 0x6b6b6b6b6b6b6b6b: 0000 [#1] PREEMPT SMP NOPTI CPU: 13 UID: 0 PID: 134 Comm: irq/156-pciehp Not tainted 6.11.0-devel+ #1 RIP: 0010:dev_driver_string+0x12/0x40 pci_destroy_slot pciehp_remove pcie_port_remove_service device_release_driver_internal bus_remove_device device_del device_unregister remove_iter device_for_each_child pcie_portdrv_remove pci_device_remove device_release_driver_internal bus_remove_device device_del pci_remove_bus_device (recursive invocation) pci_remove_bus_device pciehp_unconfigure_device pciehp_disable_slot pciehp_handle_presence_or_link_change pciehp_ist Link: https://lore.kernel.org/r/4bfd4c0e976c1776cd08e76603903b338cf25729.1728579288.git.lukas@wunner.de Reported-by: Dennis Wassenberg <[email protected]> Closes: https://lore.kernel.org/r/[email protected]/ Tested-by: Dennis Wassenberg <[email protected]> Signed-off-by: Lukas Wunner <[email protected]> Signed-off-by: Bjorn Helgaas <[email protected]> Reviewed-by: Mika Westerberg <[email protected]> Cc: [email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>

andy-shev and others added 16 commits September 8, 2016 23:35

ARM: dts: exynos5422-odroidxu3: Enable TMU at Exynos5422 base

c2e483c

This changes enables TMU IP block on the Exynos5422 Odroid-XU3 device. Signed-off-by: Anand Moon <[email protected]> Acked-by: Lukasz Majewski <[email protected]> Signed-off-by: Krzysztof Kozlowski <[email protected]>

ARM: dts: Add to enable SPI1 on ODROID-XU4

07409ca

Change-Id: I65e9f38395dddfbe14daf7300a34a955453b5cb4 Signed-off-by: Dongjin Kim <[email protected]>

staging: fbtft: Add new fbtft lcd for ODROID board

c8d9ff4

Signed-off-by: Dongjin Kim <[email protected]>

phy: exynos5-usbdrd: fixed the return value.

6fd46c9

Fixed the compilation warning. Change-Id: I4cab298773bd68eef9c1bc5972e23f627f5b691b

media/rc: fix path of header file 'gpio-ir-recv.h'

83a8dae

Change-Id: Ie2991f4d625c8e7bae9dcd07961fdb29bf6ebaff Signed-off-by: Dongjin Kim <[email protected]>

exynos5800: added higher freqs for XU4

efba67b

Added the missing freq changes for A15 and A7 Change-Id: I4f485d349393944cb8b5ae3f8177ef9c11e9290a Signed-off-by: Tom Briden <[email protected]>

ODROID-XU4 : mmc power control for UHS mode

29d5024

Change-Id: Ic65075b3167ed99d2df1adaa2eb2df7e2b59360f

ARM: dts: exynos: Add UHS-I bus speed support

21737ca

Added UHS-I bus speeds: SDR50 DDR50 SDR104 Change-Id: Iecbf6cea064b94edd71e3f60b35408ef75495815 Signed-off-by: Dongjin Kim <[email protected]>

ODROID-XU4: defconfig: add default kernel configration

5ffa33b

Change-Id: Ie34ce98fbc8a86c840673b68bf20efe9846f5404 Signed-off-by: Dongjin Kim <[email protected]>

odroidxu4_defconfig enable lvm and dm-crypt

dae522b

Merge remote-tracking branch 'remotes/kernel/linux-4.8.y' into odroid…

83d783d

…xu4-v4.8

tobetter force-pushed the odroidxu4-v4.8 branch from 5ffa33b to fa05948 Compare October 6, 2016 15:05

wildea01 and others added 12 commits October 7, 2016 15:03

USB: serial: cp210x: Add ID for a Juniper console

6bd1000

commit decc536 upstream. Signed-off-by: Kyle Jones <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

Linux 4.8.1

a7fac75

Merge remote-tracking branch 'remotes/kernel/linux-4.8.y' into odroid…

b80b4f9

…xu4-v4.8

Provide feedback

Saved searches

Use saved searches to filter your results more quickly

odroidxu4_defconfig enable lvm and dm-crypt #12

odroidxu4_defconfig enable lvm and dm-crypt #12

Dmole commented Oct 5, 2016

Dmole commented Oct 6, 2016

odroidxu4_defconfig enable lvm and dm-crypt #12

odroidxu4_defconfig enable lvm and dm-crypt #12

Conversation

Dmole commented Oct 5, 2016

Dmole commented Oct 6, 2016